Mechanical pencils — Part 1: Classification, dimensions, performance requirements and testing

This part of ISO 9177 provides a classification for hand-held mechanical pencils used for technical drawings. It specifies dimensions, performance requirements and testing requirements.

Porte-mine — Partie 1: Classification, dimensions, caractéristiques de fonctionnement et essais

Tehnični svinčniki - 1. del: Razvrstitev, mere, zahtevane karakteristike in preskušanje

Ta del standarda ISO 9177 določa razvrstitev za ročne tehnične svinčnike, ki se uporabljajo za tehnične risbe. Določa mere, zahtevane karakteristike in preskušanje.

General Information

Status
Withdrawn
Publication Date
06-Nov-2011
Withdrawal Date
06-Nov-2011
Current Stage
9599 - Withdrawal of International Standard
Completion Date
23-Sep-2016

Relations

Buy Standard

Standard
ISO 9177-1:2011 - Mechanical pencils
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 9177-1:2012
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

INTERNATIONAL  ISO
STANDARD 9177-1
Second edition
2011-11-15
Mechanical pencils —
Part 1:
Classification, dimensions, performance
requirements and testing
Porte-mine — Partie 1: Classification, dimensions, caractéristiques de
fonctionnement et essais
Reference number
ISO 9177-1:2011(E)
©
 ISO 2011

---------------------- Page: 1 ----------------------
ISO 9177-1:2011(E)
COPYRIGHT PROTECTED DOCUMENT
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 9177-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9177-1 was prepared by Technical Committee ISO/TC 10, Technical product documentation.
This second edition cancels and replaces the first edition (ISO 9177-1:1989), of which it constitutes a minor
revision.
ISO 9177 consists of the following parts, under the general title Mechanical pencils:
—  Part 1: Classification, dimensions, performance requirements and testing
—  Part 2: Black leads — Classification and dimensions
—  Part 3: Black leads — Bending strengths of HB leads
© ISO 2011 – All rights reserved  iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 9177-1:2011(E)
Mechanical pencils —
Part 1:
Classification, dimensions, performance requirements and
testing
1 Scope
This part of ISO 9177 provides a classification for hand-held mechanical pencils used for technical drawings.
It specifies dimensions, performance requirements and testing requirements.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 128-20, Technical drawings — General principles of presentation — Part 20: Basic conventions for lines
ISO 9177-2, Mechanical pencils — Part 2: Black leads — Classification and dimensions
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
mechanical pencil
hand-held line-producing tool which holds and feeds out a lead, for technical drawings
4 Classification
Mechanical pencils shall be classified according to the type of mechanism (see Table 1) and to the nominal
diameter (see Table 2). For the classification and dimensions of the leads (diameter and length), see ISO 9177-2.
Table 1 — Classification according to type of mechanism
Type classification
Mechanism Description Relevant figure
letter
a
F 1
Mechanical pencil in which the lead, housed in a barrel,
Push-type
b
is fed out by actuating a push mechanism
L 2
Mechanical pencil in which the lead, housed in a barrel,
Screw-type S 3
is fed out by actuating a propelling screw mechanism
a
  Mainly polymer leads having a nominal diameter of 0,35 mm to 1 mm.
b
  Mainly ceramic leads having a nominal diameter of 2 mm (see ISO 9177-2).
© ISO 2011 – All rights reserved  1

---------------------- Page: 4 ----------------------
ISO 9177-1:2011(E)
a) Lead in working position
b) Lead in feeding position
Key
1  guide pipe   6  nipple 11  clip
2  lead retainer   7  spring 12  cleaning pin
3  metal tip   8  lead tube 13  eraser
4  chuck   9  lead 14  eraser ferrule
5  chuck ring 10  barrel 15  push button
Figure 1 — Mechanical pencil of push-type F
2 © ISO 2011 – All rights reserved

---------------------- Page: 5 ----------------------
ISO 9177-1:2011(E)
a) Lead in working position
b) Lead in feeding position
Key
1  metal tip 5  push button
2  chuck 6  spring
3  lead tube 7  clip
4  barrel 8  lead
Figure 2 — M
...

SLOVENSKI STANDARD
SIST ISO 9177-1:2012
01-april-2012
1DGRPHãþD
SIST ISO 9177-1:1995
7HKQLþQLVYLQþQLNLGHO5D]YUVWLWHYPHUH]DKWHYDQHNDUDNWHULVWLNHLQ
SUHVNXãDQMH
Mechanical pencils - Part 1: Classification, dimensions, performance requirements and
testing
Porte-mine - Partie 1: Classification, dimensions, caractéristiques de fonctionnement et
essais
Ta slovenski standard je istoveten z: ISO 9177-1:2011
ICS:
01.100.40 Risalna oprema Drawing equipment
SIST ISO 9177-1:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 9177-1:2012

---------------------- Page: 2 ----------------------

SIST ISO 9177-1:2012
INTERNATIONAL  ISO
STANDARD 9177-1
Second edition
2011-11-15
Mechanical pencils —
Part 1:
Classification, dimensions, performance
requirements and testing
Porte-mine — Partie 1: Classification, dimensions, caractéristiques de
fonctionnement et essais
Reference number
ISO 9177-1:2011(E)
©
 ISO 2011

---------------------- Page: 3 ----------------------

SIST ISO 9177-1:2012
ISO 9177-1:2011(E)
COPYRIGHT PROTECTED DOCUMENT
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 9177-1:2012
ISO 9177-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9177-1 was prepared by Technical Committee ISO/TC 10, Technical product documentation.
This second edition cancels and replaces the first edition (ISO 9177-1:1989), of which it constitutes a minor
revision.
ISO 9177 consists of the following parts, under the general title Mechanical pencils:
—  Part 1: Classification, dimensions, performance requirements and testing
—  Part 2: Black leads — Classification and dimensions
—  Part 3: Black leads — Bending strengths of HB leads
© ISO 2011 – All rights reserved  iii

---------------------- Page: 5 ----------------------

SIST ISO 9177-1:2012

---------------------- Page: 6 ----------------------

SIST ISO 9177-1:2012
INTERNATIONAL STANDARD ISO 9177-1:2011(E)
Mechanical pencils —
Part 1:
Classification, dimensions, performance requirements and
testing
1 Scope
This part of ISO 9177 provides a classification for hand-held mechanical pencils used for technical drawings.
It specifies dimensions, performance requirements and testing requirements.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 128-20, Technical drawings — General principles of presentation — Part 20: Basic conventions for lines
ISO 9177-2, Mechanical pencils — Part 2: Black leads — Classification and dimensions
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
mechanical pencil
hand-held line-producing tool which holds and feeds out a lead, for technical drawings
4 Classification
Mechanical pencils shall be classified according to the type of mechanism (see Table 1) and to the nominal
diameter (see Table 2). For the classification and dimensions of the leads (diameter and length), see ISO 9177-2.
Table 1 — Classification according to type of mechanism
Type classification
Mechanism Description Relevant figure
letter
a
F 1
Mechanical pencil in which the lead, housed in a barrel,
Push-type
b
is fed out by actuating a push mechanism
L 2
Mechanical pencil in which the lead, housed in a barrel,
Screw-type S 3
is fed out by actuating a propelling screw mechanism
a
  Mainly polymer leads having a nominal diameter of 0,35 mm to 1 mm.
b
  Mainly ceramic leads having a nominal diameter of 2 mm (see ISO 9177-2).
© ISO 2011 – All rights reserved  1

---------------------- Page: 7 ----------------------

SIST ISO 9177-1:2012
ISO 9177-1:2011(E)
a) Lead in working position
b) Lead in feeding position
Key
1  guide pipe   6  nipple 11
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.