ISO 7823-3:2021
(Main)Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics — Part 3: Continuous cast sheets
Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics — Part 3: Continuous cast sheets
This document specifies requirements for non-modified flat poly(methyl methacrylate) (PMMA) continuous cast sheets for general-purpose use. The sheets can be colourless or coloured, and can be transparent, translucent or opaque. The thickness range of the sheets covered by document is 1 mm to 10 mm.
Plastiques — Plaques en poly(méthacrylate de méthyle) — Types, dimensions et caractéristiques — Partie 3: Plaques coulées continues
Le présent document spécifie des exigences relatives aux plaques coulées continues en poly(méthacrylate de méthyle) (PMMA), planes et non modifiées, pour usage général. Ces plaques peuvent être incolores ou colorées et peuvent être transparentes, translucides ou opaques. La plage de l'épaisseur des plaques relevant du présent document est comprise entre 1 mm et 10 mm.
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 7823-3
Third edition
2021-06
Plastics — Poly(methyl methacrylate)
sheets — Types, dimensions and
characteristics —
Part 3:
Continuous cast sheets
Plastiques — Plaques en poly(méthacrylate de méthyle) — Types,
dimensions et caractéristiques —
Partie 3: Plaques coulées continues
Reference number
©
ISO 2021
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Composition . 2
5 General requirements . 2
5.1 Protective coverings . 2
5.2 Appearance . 3
5.2.1 Surface defects . 3
5.2.2 Inclusion defects . 3
5.2.3 Classification of defects . 3
5.2.4 Distribution of defects. 3
5.3 Colour . 3
5.4 Dimensions . 3
5.4.1 Length and width . 3
5.4.2 Thickness . 4
5.4.3 Tolerances for other sheet sizes . 4
5.4.4 Conditions of measurement . 4
5.5 Basic and other properties . 4
5.5.1 Basic properties . 4
5.5.2 Other properties . 4
6 Test methods . 5
6.1 General . 5
6.1.1 Sampling. 5
6.1.2 Conditioning and testing atmospheres . 5
6.1.3 Preparation of test specimens . 5
6.1.4 Specimen thickness . 5
6.2 Appearance . 5
6.3 Colour . 6
6.4 Dimensions . 6
6.5 Mechanical properties . 6
6.6 Thermal properties . 6
6.7 Flammability . 6
6.8 Optical properties . 7
6.9 Other properties . 7
7 Retest and rejection . 7
Annex A (normative) Determination of dimensional change on heating (shrinkage) .8
Bibliography .10
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 7823-3:2007), of which it constitutes a
minor revision. The changes compared to the previous edition are as follows:
— the normative references clause has been updated.
A list of all parts in the ISO 7823 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
INTERNATIONAL STANDARD ISO 7823-3:2021(E)
Plastics — Poly(methyl methacrylate) sheets — Types,
dimensions and characteristics —
Part 3:
Continuous cast sheets
1 Scope
This document specifies requirements for non-modified flat poly(methyl methacrylate) (PMMA)
continuous cast sheets for general-purpose use. The sheets can be colourless or coloured, and can be
transparent, translucent or opaque.
The thickness range of the sheets covered by document is 1 mm to 10 mm.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-2:2013, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and
ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 306:2013, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 489:1999, Plastics — Determination of refractive index
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 877-1, Plastics — Methods of exposure to solar radiation — Part 1: General guidance
ISO 877-2, Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure
behind window glass
ISO 877-3, Plastics — Methods of exposure to solar radiation — Part 3: Intensified weathering using
concentrated solar radiation
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pycnometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method
ISO 2039-2, Plastics — Determination of hardness — Part 2: Rockwell hardness
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 4582, Plastics — Determination of changes in colour and variations in properties after exposure to
glass-filtered solar radiation, natural weathering or laboratory radiation sources
ISO 4892-2:2013, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 4892-4, Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc
lamps
ISO 11359-2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear
thermal expansion and glass transition temperature
ISO 13468-1, Plastics — Determination of the total luminous transmittance of transparent materials —
Part 1: Single-beam instrument
ISO 13468-2, Plastics — Determination of the total luminous transmittance of transparent materials —
Part 2: Double-beam instrument
ISO 14782, Plastics — Determination of haze for transparent materials
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain
...
NORME ISO
INTERNATIONALE 7823-3
Troisième édition
2021-06
Plastiques — Plaques en
poly(méthacrylate de méthyle)
— Types, dimensions et
caractéristiques —
Partie 3:
Plaques coulées continues
Plastics — Poly(methyl methacrylate) sheets — Types, dimensions
and characteristics —
Part 3: Continuous cast sheets
Numéro de référence
©
ISO 2021
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Composition . 2
5 Exigences générales . 3
5.1 Protection des plaques . 3
5.2 Aspect . . 3
5.2.1 Défauts de surface . 3
5.2.2 Défauts d’inclusion . 3
5.2.3 Classification des défauts . 3
5.2.4 Répartition des défauts . 3
5.3 Couleur . 3
5.4 Dimensions . 3
5.4.1 Longueur et largeur . 3
5.4.2 Épaisseur . 4
5.4.3 Tolérances sur d'autres tailles de plaque . 4
5.4.4 Conditions de mesurage . 4
5.5 Propriétés fondamentales et autres propriétés . 4
5.5.1 Propriétés fondamentales. 4
5.5.2 Autres propriétés . 4
6 Méthodes d’essai . 5
6.1 Généralités . 5
6.1.1 Échantillonnage . 5
6.1.2 Atmosphères de conditionnement et d'essai . 5
6.1.3 Préparation des éprouvettes . 6
6.1.4 Épaisseur des éprouvettes. 6
6.2 Aspect . . 6
6.3 Couleur . 6
6.4 Dimensions . 6
6.5 Propriétés mécaniques . 6
6.6 Propriétés thermiques . 6
6.7 Inflammabilité . 7
6.8 Propriétés optiques. 7
6.9 Autres propriétés . 7
7 Contre-épreuve et rejets . 7
Annexe A (normative) Détermination des variations dimensionnelles (retrait) en chauffage .8
Bibliographie .10
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 11,
Produits, en collaboration avec le comité technique CEN/TC 249, Plastiques, du Comité européen de
normalisation (CEN), conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord
de Vienne).
Cette troisième édition annule et remplace la deuxième édition (ISO 7823-3:2007), dont elle constitue
une révision mineure. Les modifications par rapport à l’édition antérieure sont les suivantes :
— l’article sur les références normatives a été mis à jour.
Une liste de toutes les parties de la série ISO 7823 se trouve sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés
NORME INTERNATIONALE ISO 7823-3:2021(F)
Plastiques — Plaques en poly(méthacrylate de méthyle) —
Types, dimensions et caractéristiques —
Partie 3:
Plaques coulées continues
1 Domaine d’application
Le présent document spécifie des exigences relatives aux plaques coulées continues en poly(méthacrylate
de méthyle) (PMMA), planes et non modifiées, pour usage général. Ces plaques peuvent être incolores
ou colorées et peuvent être transparentes, translucides ou opaques.
La plage de l'épaisseur des plaques relevant du présent document est comprise entre 1 mm et 10 mm.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s’applique (y compris les
éventuels amendements).
ISO 62, Plastiques — Détermination de l'absorption d'eau
ISO 75-2:2013, Plastiques — Détermination de la température de fléchissement sous charge — Partie 2:
Plastiques et ébonite
ISO 178, Plastiques — Détermination des propriétés en flexion
ISO 179-1, Plastiques — Détermination des caractéristiques au choc Charpy — Partie 1: Essai de choc non
instrumenté
ISO 291, Plastiques — Atmosphères normales de conditionnement et d'essai
ISO 306:2013, Plastiques — Matières thermoplastiques — Détermination de la température de
ramollissement Vicat (VST)
ISO 489:1999, Plastiques — Détermination de l'indice de réfraction
ISO 527-2, Plastiques — Détermination des propriétés en traction — Partie 2: Conditions d'essai des
plastiques pour moulage et extrusion
ISO 877-1, Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 1: Lignes directrices
générales
ISO 877-2, Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 2: Exposition directe et
exposition derrière une vitre en verre
ISO 877-3, Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 3: Exposition intensifiée
par rayonnement solaire concentré
ISO 1183-1, Plastiques — Méthodes de détermination de la masse volumique des plastiques non
alvéolaires — Partie 1: Méthode par immersion, méthode du pycnomètre en milieu liquide et méthode par
titrage
ISO 1183-2, Plastiques — Méthodes de détermination de la masse volumique des plastiques non
alvéolaires — Partie 2: Méthode de la colonne à gradient de masse volumique
ISO 2039-2, Plastiques — Détermination de la dureté — Partie 2: Dureté Rockwell
ISO 2818, Plastiques — Préparation des éprouvettes par usinage
ISO 4582, Plastiques — Détermination des changements de coloration et des variations de propriétés après
exposition au rayonnement solaire sous verre, aux agents atmosphériques ou aux sources de rayonnement
de laboratoire
ISO 4892-2:2013, Plastiques — Méthodes d’exposition à des sourc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.