Extruded sheets of polyethylene (PE-HD) — Requirements and test methods

This document specifies the requirements and test methods for solid flat extruded sheets of polyethylene homopolymers (PE-HD) without fillers or reinforcing materials. This document is applicable only to thicknesses of 0,5 mm to 40 mm. It also applies to PE-HD sheet in rolled form.

Plaques extrudées en polyéthylène (PE-HD) — Exigences et méthodes d'essai

Le présent document spécifie les exigences et les méthodes d’essai pour les plaques massives et planes, extrudées en homopolymères de polyéthylène (PE-HD) sans adjonction de charges ou de renforts. Le présent document s’applique exclusivement aux plaques de 0,5 mm à 40 mm d’épaisseur. Il s’applique également aux feuilles de PE-HD enroulées sur rouleau.

General Information

Status
Published
Publication Date
20-May-2021
Current Stage
6060 - International Standard published
Start Date
21-May-2021
Due Date
25-Sep-2021
Completion Date
21-May-2021
Ref Project

Relations

Buy Standard

Standard
ISO 14632:2021 - Extruded sheets of polyethylene (PE-HD) -- Requirements and test methods
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 14632:2021 - Plaques extrudées en polyéthylène (PE-HD) -- Exigences et méthodes d'essai
French language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 14632:Version 05-feb-2021 - Extruded sheets of polyethylene (PE-HD) -- Requirements and test methods
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 14632:Version 06-mar-2021 - Plaques extrudées en polyéthylene (PE-HD) -- Exigences et méthodes d'essai
French language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 14632
Second edition
2021-05
Extruded sheets of polyethylene
(PE-HD) — Requirements and test
methods
Plaques extrudées en polyéthylène (PE-HD) — Exigences et méthodes
d'essai
Reference number
ISO 14632:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 14632:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 14632:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material . 2
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . 2
5.2.3 Rectangularity . 3
5.2.4 Bow of sheets in rolled form . 3
5.3 Properties . 3
5.3.1 Mechanical and thermal properties . 3
5.3.2 Behaviour after heating . 4
5.3.3 Physiological behaviour . . 4
6 Test methods . 4
6.1 Test specimens . 4
6.1.1 Preparation of test specimens . 4
6.1.2 Conditioning . 5
6.1.3 Testing . 5
6.2 Delivery condition . 5
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness (h) . 5
6.4.2 Length (l) and width (b) . . 5
6.4.3 Rectangularity . 5
6.4.4 Bow of sheets in rolled form . 6
6.5 Density . 6
6.6 Tensile stress at yield (σ ) and tensile strain at yield (ε ) . 6
y y
6.7 Modulus of elasticity in tension (E ) . 6
t
6.8 Charpy impact strength of notched specimens (a ) . 6
cn
6.9 Melt mass-flow rate (MFR) . 6
6.10 Determination of shrinkage after heating . 6
7 Designation . 7
7.1 Example for PE-HD sheets . 7
7.2 Example for PE- HD sheets in rolled form . 8
8 Marking . 8
Annex A (normative) Requirements for rectangularity . 9
© ISO 2021 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 14632:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 14632:1998), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the range of MFR values for PE HD sheet group 1 in Table 2 has been changed to cover the wider PE
100 grade of extruded PE HD sheets.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 14632:2021(E)
Extruded sheets of polyethylene (PE-HD) — Requirements
and test methods
1 Scope
This document specifies the requirements and test methods for solid flat extruded sheets of
polyethylene homopolymers (PE-HD) without fillers or reinforcing materials.
This document is applicable only to thicknesses of 0,5 mm to 40 mm. It also applies to PE-HD sheet in
rolled form.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 1: Standard method
ISO 1133-2, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pycnometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method
ISO 1183-3, Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas
pyknometer method
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 9080, Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of
thermoplastics materials in pipe form by extrapolati
...

NORME ISO
INTERNATIONALE 14632
Deuxième édition
2021-05
Plaques extrudées en polyéthylène
(PE-HD) — Exigences et méthodes
d'essai
Extruded sheets of polyethylene (PE-HD) — Requirements and test
methods
Numéro de référence
ISO 14632:2021(F)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 14632:2021(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 14632:2021(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Matière . 2
5 Exigences . 2
5.1 Aspect . . 2
5.2 Tolérances dimensionnelles . 2
5.2.1 Épaisseur . 2
5.2.2 Longueur et largeur . 2
5.2.3 Rectangularité . 3
5.2.4 Cambrage des plaques en rouleaux . 3
5.3 Propriétés . 3
5.3.1 Propriétés mécaniques et thermiques . 3
5.3.2 Comportement après traitement thermique . 4
5.3.3 Comportement physiologique . 4
6 Méthodes d’essai . 4
6.1 Éprouvettes . 4
6.1.1 Préparation des éprouvettes . 4
6.1.2 Conditionnement . 5
6.1.3 Essai . 5
6.2 État de livraison . 5
6.3 Aspect . . 5
6.4 Dimensions . 5
6.4.1 Épaisseur (h) . 5
6.4.2 Longueur (l) et largeur (b) . 5
6.4.3 Rectangularité . 6
6.4.4 Cambrage des plaques en rouleaux . 6
6.5 Masse volumique. 6
6.6 Contrainte en traction au seuil d’écoulement (σ ) et allongement au seuil
y
d’écoulement (ε ) . 6
y
6.7 Module d’élasticité en traction (E ) . 6
t
6.8 Résistance au choc Charpy sur éprouvette entaillée (a ) . 6
cn
6.9 Indice de fluidité à chaud en masse (MFR) . 6
6.10 Détermination du retrait après chauffage . 6
7 Désignation . 8
7.1 Exemple pour les plaques en PE-HD . 8
7.2 Exemple pour les plaques en PE-HD en rouleau . 8
8 Marquage . 8
Annexe A (normative) Exigences pour la rectangularité . 9
© ISO 2021 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 14632:2021(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 11,
Produits, en collaboration avec le comité technique CEN/TC 249, Plastiques, du Comité européen de
normalisation (CEN), conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord
de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 14632:1998), qui a fait l’objet d’une
révision technique.
Les principales modifications par rapport à l’édition antérieure sont les suivantes:
— la gamme des valeurs de MFR pour le groupe 1 des plaques en PE-HD dans le Tableau 2 a été modifiée
pour couvrir le grade plus large du PE 100 des plaques en PE-HD extrudées.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 14632:2021(F)
Plaques extrudées en polyéthylène (PE-HD) — Exigences et
méthodes d'essai
1 Domaine d’application
Le présent document spécifie les exigences et les méthodes d’essai pour les plaques massives et planes,
extrudées en homopolymères de polyéthylène (PE-HD) sans adjonction de charges ou de renforts.
Le présent document s’applique exclusivement aux plaques de 0,5 mm à 40 mm d’épaisseur. Il s’applique
également aux feuilles de PE-HD enroulées sur rouleau.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s’applique (y compris les
éventuels amendements).
ISO 179-1, Plastiques — Détermination des caractéristiques au choc Charpy — Partie 1: Essai de choc non
instrumenté
ISO 179-2, Plastiques — Détermination des caractéristiques au choc Charpy — Partie 2: Essai de choc
instrumenté
ISO 291, Plastiques — Atmosphères normales de conditionnement et d'essai
ISO 527-1, Plastiques — Détermination des propriétés en traction — Partie 1: Principes généraux
ISO 527-2, Plastiques — Détermination des propriétés en traction — Partie 2: Conditions d'essai des
plastiques pour moulage et extrusion
ISO 1133-1, Plastiques — Détermination de l'indice de fluidité à chaud des thermoplastiques, en masse
(MFR) et en volume (MVR) — Partie 1: Méthode normale
ISO 1133-2, Plastiques — Détermination de l'indice de fluidité à chaud des thermoplastiques, en masse
(MFR) et en volume (MVR) — Partie 2: Méthode pour les matériaux sensibles à l'historique temps-
température et/ou à l'humidité
ISO 1183-1, Plastiques — Méthodes de détermination de la masse volumique des plastiques non
alvéolaires — Partie 1: Méthode par immersion, méthode du pycnomètre en milieu liquide et méthode par
titrage
ISO 1183-2, Plastiques — Méthodes de détermination de la masse volumique des plastiques non
alvéolaires — Partie 2: Méthode de la colonne à gradient de masse volumique
ISO 1183-3, Plastiques — Méthodes pour déterminer la masse volumique des plastiques non alvéolaires —
Partie 3: Méthode utilisant un pycnomètre à gaz
ISO 2818, Plastiques — Préparation des éprouvettes par usinage
ISO 9080, Systèmes de canalisations et de gaines en matières plastiques — Détermination de la résistance
hydrostatique à long terme des matières thermoplastiques sous forme de tubes par extrapolation
ISO 17855-1, Plastiques — Polyéthylène (PE) pour moulage et extrusion — Partie 1: Système de désignation
et base de spécification
© ISO 2021 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 14632:2021(F)

3 Termes et définitions
Aucun terme n’est défini dans le présent document.
L'ISO
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 14632
ISO/TC 61/SC 11
Extruded sheets of polyethylene (PE-
Secretariat: JISC
HD) — Requirements and test methods
Voting begins on:
2021­02­15
Plaques extrudées en polyéthylène (PE-HD) — Exigences et méthodes
d'essai
Voting terminates on:
2021­04­11
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 14632:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2021

---------------------- Page: 1 ----------------------
ISO/FDIS 14632:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH­1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 14632:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material . 2
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . 2
5.2.3 Rectangularity . 3
5.2.4 Bow of sheets in rolled form . 3
5.3 Properties . 3
5.3.1 Mechanical and thermal properties . 3
5.3.2 Behaviour after heating . 4
5.3.3 Physiological behaviour . . 4
6 Test methods . 4
6.1 Test specimens . 4
6.1.1 Preparation of test specimens . 4
6.1.2 Conditioning . 5
6.1.3 Testing . 5
6.2 Delivery condition . 5
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness (h) . 5
6.4.2 Length (l) and width (b) . . 5
6.4.3 Rectangularity . 5
6.4.4 Bow of sheets in rolled form . 6
6.5 Density . 6
6.6 Tensile stress at yield (σ ) and tensile strain at yield (ε ) . 6
y y
6.7 Modulus of elasticity in tension (E ) . 6
t
6.8 Charpy impact strength of notched specimens (a ) . 6
cn
6.9 Melt mass-flow rate (MFR) . 6
6.10 Determination of shrinkage after heating . 6
7 Designation . 7
7.1 Example for PE-HD sheets . 7
7.2 Example for PE- HD sheets in rolled form . 8
8 Marking . 8
Annex A (normative) Requirements for rectangularity . 9
© ISO 2021 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/FDIS 14632:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non­governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 14632:1998), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the range of MFR values for PE HD sheet group 1 in Table 2 has been changed to cover the wider PE
100 grade of extruded PE HD sheets.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 14632:2021(E)
Extruded sheets of polyethylene (PE-HD) — Requirements
and test methods
1 Scope
This document specifies the requirements and test methods for solid flat extruded sheets of
polyethylene homopolymers (PE-HD) without fillers or reinforcing materials.
This document is applicable only to thicknesses of 0,5 mm to 40 mm. It also applies to PE-HD sheet in
rolled form.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 179­1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179­2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 527­1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527­2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1133­1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 1: Standard method
ISO 1133­2, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 1183­1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pycnometer method and titration method
ISO 1183­2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method
ISO 1183­3, Plastics — Methods for determin
...

PROJET
NORME ISO/FDIS
FINAL
INTERNATIONALE 14632
ISO/TC 61/SC 11
Plaques extrudées en polyéthylène (PE-
Secrétariat: JISC
HD) — Exigences et méthodes d'essai
Début de vote:
2021-02-15
Extruded sheets of polyethylene (PE-HD) — Requirements and test
methods
Vote clos le:
2021-04-11
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSER-
VATIONS, NOTIFICATION DES DROITS DE PRO-
TRAITEMENT PARALLÈLE ISO/CEN
PRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT
CONNAISSANCE ET À FOURNIR UNE DOCUMEN-
TATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-
Numéro de référence
MERCIALES, AINSI QUE DU POINT DE VUE
ISO/FDIS 14632:2021(F)
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR POSSI-
BILITÉ DE DEVENIR DES NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTA-
©
TION NATIONALE. ISO 2021

---------------------- Page: 1 ----------------------
ISO/FDIS 14632:2021(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO/FDIS 14632:2021(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Matière . 2
5 Exigences . 2
5.1 Aspect . . 2
5.2 Tolérances dimensionnelles . 2
5.2.1 Épaisseur . 2
5.2.2 Longueur et largeur . 2
5.2.3 Rectangularité . 3
5.2.4 Cambrage des plaques en rouleaux . 3
5.3 Propriétés . 3
5.3.1 Propriétés mécaniques et thermiques . 3
5.3.2 Comportement après traitement thermique . 4
5.3.3 Comportement physiologique . 4
6 Méthodes d’essai . 4
6.1 Éprouvettes . 4
6.1.1 Préparation des éprouvettes . 4
6.1.2 Conditionnement . 5
6.1.3 Essai . 5
6.2 État de livraison . 5
6.3 Aspect . . 5
6.4 Dimensions . 5
6.4.1 Épaisseur (h) . 5
6.4.2 Longueur (l) et largeur (b) . 5
6.4.3 Rectangularité . 6
6.4.4 Cambrage des plaques en rouleaux . 6
6.5 Masse volumique. 6
6.6 Contrainte en traction au seuil d’écoulement (σ ) et allongement au seuil
y
d’écoulement (ε ) . 6
y
6.7 Module d’élasticité en traction (E ) . 6
t
6.8 Résistance au choc Charpy sur éprouvette entaillée (a ) . 6
cn
6.9 Indice de fluidité à chaud en masse (MFR) . 6
6.10 Détermination du retrait après chauffage . 6
7 Désignation . 8
7.1 Exemple pour les plaques en PE-HD . 8
7.2 Exemple pour les plaques en PE-HD en rouleau . 8
8 Marquage . 8
Annexe A (normative) Exigences pour la rectangularité . 9
© ISO 2021 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO/FDIS 14632:2021(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www .iso .org/ iso/ fr/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 11,
Produits, en collaboration avec le comité technique CEN/TC 249, Plastiques, du Comité européen de
normalisation (CEN), conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord
de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 14632:1998), qui a fait l’objet d’une
révision technique.
Les principales modifications par rapport à l’édition antérieure sont les suivantes:
— la gamme des valeurs de MFR pour le groupe 1 des plaques en PE-HD dans le Tableau 2 a été modifiée
pour couvrir le grade plus large du PE 100 des plaques en PE-HD extrudées.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés

---------------------- Page: 4 ----------------------
PROJET FINAL DE NORME INTERNATIONALE ISO/FDIS 14632:2021(F)
Plaques extrudées en polyéthylène (PE-HD) — Exigences et
méthodes d'essai
1 Domaine d’application
Le présent document spécifie les exigences et les méthodes d’essai pour les plaques massives et planes,
extrudées en homopolymères de polyéthylène (PE-HD) sans adjonction de charges ou de renforts.
Le présent document s’applique exclusivement aux plaques de 0,5 mm à 40 mm d’épaisseur. Il s’applique
également aux feuilles de PE-HD enroulées sur rouleau.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s’applique (y compris les
éventuels amendements).
ISO 179-1, Plastiques — Détermination des caractéristiques au choc Charpy — Partie 1: Essai de choc non
instrumenté
ISO 179-2, Plastiques — Détermination des caractéristiques au choc Charpy — Partie 2: Essai de choc
instrumenté
ISO 291, Plastiques — Atmosphères normales de conditionnement et d'essai
ISO 527-1, Plastiques — Détermination des propriétés en traction — Partie 1: Principes généraux
ISO 527-2, Plastiques — Détermination des propriétés en traction — Partie 2: Conditions d'essai des
plastiques pour moulage et extrusion
ISO 1133-1, Plastiques — Détermination de l'indice de fluidité à chaud des thermoplastiques, en masse
(MFR) et en volume (MVR) — Partie 1: Méthode normale
ISO 1133-2, Plastiques — Détermination de l'indice de fluidité à chaud des thermoplastiques, en masse
(MFR) et en volume (MVR) — Partie 2: Méthode pour les matériaux sensibles à l'historique temps-
température et/ou à l'humidité
ISO 1183-1, Plastiques — Méthodes de détermination de la masse volumique des plastiques non alvéolaires —
Partie 1: Méthode par immersion, méthode du pycnomètre en milieu liquide et méthode par titrage
ISO 1183-2, Plastiques — Méthodes de détermination de la masse volumique des plastiques non
alvéolaires — Partie 2: Méthode de la colonne à gradient de masse volumique
ISO 1183-3, Plastiques — Méthodes pour déterminer la masse volumique des plastiques non alvéolaires —
Partie 3: Méthode utilisant un pycnomètre à gaz
ISO 2818, Plastiques — Préparation des éprouvettes par usinage
ISO 9080, Systèmes de canalisations et de gaines en matières plastiques — Détermination de la résistance
hydrostatique à long terme des matières thermoplastiques sous forme de tube
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.