ISO 6363-3:2012

Wrought aluminium and aluminium alloys - Cold-drawn rods/bars, tubes and wires - Part 3: Drawn round bars and wires - Tolerances on form and dimensions (symmetric plus and minus tolerances on diameter)

ISO 6363-3:2012 specifies tolerances on form and dimensions for wrought aluminium and aluminium alloy drawn round bars and wires having diameters in the range of from 1 mm to 100 mm inclusive. The tolerances on diameter specified in ISO 6363-3:2012 are symmetric plus and minus tolerances.

Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 3: Barres rondes et fils étirés — Tolérances sur forme et dimensions (tolérances de diamètre symétriques en plus et en moins)

General Information

• Status: Withdrawn
• Publication Date: 11-Jul-2012
• ICS: 77.150.10 - Aluminium products
• Technical Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Drafting Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Current Stage: 9599 - Withdrawal of International Standard
• Start Date: 01-Jul-2022
• Completion Date: 13-Dec-2025

Relations

• Revised: ISO 6363-3:2022 - Wrought aluminium and aluminium alloys - Cold-drawn rods/bars, tubes and wires - Part 3: Tolerances on form and dimensions for drawn rods/bars and wires
• Effective Date: 23-Apr-2020
• Revises: ISO 5193:1981 - Wrought aluminium and aluminium alloys - Drawn round bars - Tolerances on shape and dimensions (Symmetric plus and minus tolerances on diameter)
• Effective Date: 23-May-2009

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6363-3
First edition
2012-07-15
Wrought aluminium and aluminium
alloys — Cold-drawn rods/bars, tubes
and wires —
Part 3:
Drawn round bars and
wires — Tolerances on form and
dimensions (symmetric plus and minus
tolerances on diameter)
Aluminium et alliages d’aluminium corroyés — Barres, tubes et fils
étirés à froid —
Partie 3: Barres rondes et fils étirés — Tolérances sur forme et
dimensions (tolérances de diamètre symétriques en plus et en moins)
Reference number
©
ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Tolerances on shape and dimensions . 1
4.1 Diameter . 1
4.2 Circularity . 2
4.3 Straightness . 2
4.4 Fixed lengths . 2
4.5 Squareness of cut ends . 3
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6363-3 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee
SC 6, Wrought aluminium and aluminium alloys.
ISO 6363-3 cancels and replaces ISO 5193:1981 which has been technically revised.
ISO 6363 consists of the
...