ISO/TS 18339:2015
(Main)Endotherapy devices — Eyepiece cap and light guide connector
Endotherapy devices — Eyepiece cap and light guide connector
ISO/TS 18339:2015 specifies the design of eyepiece cap and light guide connector of an endoscope to enable the combination of products from different manufacturers. The products intended only for limited combination are out of the scope. It is a mechanical connection; it might not generate best results, but it allows the user to be able to work. ISO/TS 18339:2015 supports manufacturers of components in the design of interfaces.
Dispositifs d'endothérapie — Bouchon d'oculaire et raccord de guide de lumière
General Information
Buy Standard
Standards Content (Sample)
© ISO 2015 – All rights reserved
ISO/TC 172/SC 5
Date: 2015-07-17
ISO/TS 18339:2015(E)
ISO/TC 172/SC 5/WG 6
Secretariat: DIN
Endoscopes — Eyepiece cap and light guide connector
Endoscopes — Bonnette d’oculaire et connecteur de fibres optiques
Document type: Technical Specification
Document subtype:
Document stage: (60) Publication
Document language: E
O:\Documents\TC172\SC005\062211 - ISO_NP TS 18339 (Ed
1)\60.00\300\C062211e_trackchanges.docx STD Version 2.5a
---------------------- Page: 1 ----------------------
ISO/TS 18339:2015(E)
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user's country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 18339:2015(E)
Contents Page
Foreword .4
Introduction .5
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Dimensions .2
4.1 Eyepiece cap .2
4.1.1 Eyepiece cap with straight edges .2
4.1.2 Eyepiece cap with curved edges .2
4.2 Light guide connector.4
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TS 18339:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 172, Optics and photonics, Subcommittee SC 5,
Microscopes and endoscopes.
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/TS 18339:2015(E)
Introduction
To carry out minim
...
TECHNICAL ISO/TS
SPECIFICATION 18339
First edition
2015-11-01
Endotherapy devices — Eyepiece cap
and light guide connector
Dispositifs d’endothérapie — Bouchon d’oculaire et raccord de
guide de lumière
Reference number
ISO/TS 18339:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO/TS 18339:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 18339:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
4.1 Eyepiece cap . 1
4.1.1 Eyepiece cap with straight edges . 1
4.1.2 Eyepiece cap with curved edges . 2
4.2 Light guide connector . 3
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TS 18339:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 172, Optics and photonics, Subcommittee SC 5,
Microscopes and endoscopes.
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/TS 18339:2015(E)
Introduction
To carry out minimal invasi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.