ISO 6469-2:2018

Electrically propelled road vehicles - Safety specifications - Part 2: Vehicle operational safety

ISO 6469-2:2018 specifies requirements for operational safety specific to electrically propelled road vehicles, for the protection of persons inside and outside the vehicle. NOTE 1 Relevant requirements for motorcycles and mopeds are described in ISO 13063. ISO 6469-2:2018 does not provide comprehensive safety information for manufacturing, maintenance and repair personnel. ISO 6469-2:2018 does not consider specific aspects of driving automation features. NOTE 2 For definition of the term "driving automation features", see SAE J3016.

Véhicules routiers électriques — Spécifications de sécurité — Partie 2: Sécurité fonctionelle du véhicule

General Information

• Status: Withdrawn
• Publication Date: 24-Jan-2018
• ICS: 43.120 - Electric road vehicles
• Technical Committee: ISO/TC 22/SC 37 - Electrically propelled vehicles
• Drafting Committee: ISO/TC 22/SC 37 - Electrically propelled vehicles
• Current Stage: 9599 - Withdrawal of International Standard
• Start Date: 16-May-2022
• Completion Date: 13-Dec-2025

Relations

• Revised: ISO 6469-2:2022 - Electrically propelled road vehicles - Safety specifications - Part 2: Vehicle operational safety
• Effective Date: 10-Jul-2021
• Revises: ISO 6469-2:2009 - Electrically propelled road vehicles - Safety specifications - Part 2: Vehicle operational safety means and protection against failures
• Effective Date: 05-Nov-2015

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6469-2
Third edition
2018-02
Electrically propelled road vehicles —
Safety specifications —
Part 2:
Vehicle operational safety
Véhicules routiers électriques — Spécifications de sécurité —
Partie 2: Sécurité fonctionelle du véhicule
Reference number
©
ISO 2018
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Environmental and operating conditions . 3
5 Operational safety . 3
5.1 General . 3
5.2 Driving-enabled mode . 3
5.3 Driving . 4
5.3.1 Indication of reduced propulsion power . 4
5.3.2 Low energy content of RESS . 4
5.3.3 Driving backwards . 4
5.4 Parking . 4
5.5 Connection of the vehicle to an external electric power supply. 4
5.6 Electromagnetic compatibility . 5
6 Owner's manual . 5
7 Information for first responders . 5
Bibliography . 6
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 37,
Electrically propelled vehicles.
This third edition cancels and replaces the second edition (ISO 6469-2:2009), which has been technically
revised. The main changes compared to the previous edition are as follows:
— clarification of the single-point failure definition and related measures;
— improvement of the operational safety requirements for the driving-enabled mode;
— elimination of marking requirements;
— clear requirements for connection of the vehicle to an external electric power supply;
— simplification of EMC requirements.
iv © ISO 2018 – All rights reserved

INTERNATIONAL STANDARD ISO 6469-2:2018(E)
Electrically propelled road vehicles — Safety
specifications —
Part 2:
Vehicle operational safety
1 Scope
This document specifies requirements for operational safety specific to electrically propelled road
vehicles, for the protection of persons inside and outside the vehicle.
NOTE 1 Relevant requirements for motorcycles and mopeds are described in ISO 13063.
This document does not provide comprehensive safety information for manufacturing, maintenance
and repair personnel.
This document does not consider specific aspects of driving automation features.
NOTE 2 For definition of the term “driving automation features”, see SAE J3016.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 11451 (all parts), Road vehicles — Vehicle test methods for electrical disturbances from narrowband
radiated electromagnetic energy
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
auxiliary electric system
vehicle system, other than for vehicle propulsion, that operates on electric energy
3.2
case A
connection of an EV (3.7) to the supply network with a plug and cable permanently attached to the EV
3.3
case B
connection of an EV (3.7) to the a.c. supply network with a cable assembly detachable at both ends
3.4
c
...