ISO 4427-2:2019/Amd 1:2023

Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 2: Pipes — Amendment 1

Systèmes de canalisations en plastique destinés à l'alimentation en eau et aux branchements et collecteurs d'assainissement sous pression — Polyéthylène (PE) — Partie 2: Tubes — Amendement 1

General Information

• Status: Published
• Publication Date: 19-Feb-2023
• ICS: 23.040.20 - Plastics pipes
• ICS: 91.140.60 - Water supply systems
• ICS: 93.025 - External water conveyance systems
• Technical Committee: ISO/TC 138/SC 2 - Plastics pipes and fittings for water supplies
• Drafting Committee: ISO/TC 138/SC 2/WG 4 - PE piping systems for water supply
• Current Stage: 6060 - International Standard published
• Start Date: 20-Feb-2023
• Due Date: 04-Nov-2022
• Completion Date: 20-Feb-2023

Relations

• Amends: ISO 4427-2:2019 - Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 2: Pipes
• Effective Date: 25-Dec-2021

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 4427-2
Second edition
2019-08
AMENDMENT 1
2023-02
Plastics piping systems for water
supply, and for drainage and sewerage
under pressure — Polyethylene
(PE) —
Part 2:
Pipes
AMENDMENT 1
Systèmes de canalisations en plastique destinés à l'alimentation
en eau et aux branchements et collecteurs d'assainissement sous
pression — Polyéthylène (PE) —
Partie 2: Tubes
AMENDEMENT 1
Reference number
ISO 4427-2:2019/Amd.1:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 4427-2:2019/Amd.1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4427-2:2019/Amd.1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifyi
...