ISO/TS 23301:2023
(Main)STEP geometry visualization services
STEP geometry visualization services
This document defines a set of metadata to support the audit trail of the transformation of a geometry definition, while it is distributed and shared in supply-chains, to ensure the traceability of geometric model data. It also defines a set of web services based on the utilisation of these metadata. The following are within the scope of this document: — metadata definitions for geometry transformation audit trail: — syntax for storing these metadata in geometry data sets in various formats; — conformance level for implementers and business processes; — definitions of web services to query the geometric model data set and its associated metadata. The following are outside the scope of this document: — service specifications for CAD operations; — specifications of a cybersecurity infrastructure to enable web services; — the technical implementation of a STEP geometry services client or server; — any geometric model definition; — any product and manufacturing information (PMI) definition; — archiving.
Services de visualisation de la géométrie STEP
General Information
Relations
Buy Standard
Standards Content (Sample)
FINAL
TECHNICAL ISO/DTS
DRAFT
SPECIFICATION 23301
ISO/TC 184/SC 4
STEP geometry visualization services
Secretariat: ANSI
Voting begins on: Services de visualisation de la géométrie STEP
2023-08-03
Voting terminates on:
2023-09-28
This draft is submitted to a parallel vote in ISO and in IEC.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/DTS 23301:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 1 ----------------------
ISO/DTS 23301:2023(E)
FINAL
TECHNICAL ISO/DTS
DRAFT
SPECIFICATION 23301
ISO/TC 184/SC 4
STEP geometry visualization services
Secretariat: ANSI
Voting begins on: Services de visualisation de la géométrie STEP
Voting terminates on:
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
This draft is submitted to a parallel vote in ISO and in IEC.
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/DTS 23301:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 2 ----------------------
ISO/DTS 23301:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 High level business scenarios .4
4.1 General . 4
4.2 Check for updates . 4
4.3 Visualization number 1 . 4
4.4 Visualization number 2 . 5
4.5 Retrieve product lifecycle management (PLM) data of a product . 5
4.6 Archiving . 5
4.7 Spatial query
...
© ISO 2023 – All rights reserved
ISO/DTS 23301:2023(E)
ISO/TC 184/SC 4/JWG 16
Secretariat: ANSI
Date: 2023-05-1207-19
STEP geometry visualization services
Services de visualisation de la géométrie STEP
---------------------- Page: 1 ----------------------
ISO/DTS 23301:2023(E)
CD
FDIS stage
2 © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DTS 23301:2023(E)
Warning for WDs and CDs
This document is not an ISO International Standard. It is distributed for review and comment. It is subject to
change without notice and may not be referred to as an International Standard.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
---------------------- Page: 3 ----------------------
ISO/DTS 23301:(E)
iv © ISO 2023 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/DTS 23301:(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Field Code Changed
ISO draws attention to the possibility that the implementation of this document may involve the use of
(a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice
of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for
identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
Field Code Changed
This document was prepared jointly by Technical Committee ISO/TC 184, Automation systems and
integration, Subcommittee SC 4, Industrial data, in collaboration with Joint Technical Committee ISO/IEC
JTC 1, Information technology, Subcommittee SC 24, Computer graphics, image processing and
environmental data representation and ISO/TC 171, Document management applications, Subcommittee
SC 2, Document file formats, EDMS systems and authenticity of information.
This second edition cancels and replaces the first edition (ISO/TS 23301:2021), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— addition of a new high-level business scenario: spatial query;
— addition of a new requirement: large model presentation: bounding boxes;
— addition of a new requirement: large model presentation: occurrence tree;
— addition of a new metadata: this -URI defining the URI of the current data set;
— updates in the services definition;
— addition of a new service: get_available_formats.
Any feedback or questions on this document should be directed to the user’s national standards body. A
comp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.