ISO 8665-2:2024

Small craft — Power measurements and declarations — Part 2: Electric marine propulsion

This document specifies the requirements for the determination of the power of electric marine propulsion systems when presented for documenting and checking of the declared (rated) power published by the manufacturer. This document is applicable to electric systems used for propulsion of recreational craft and other small craft of up to 24 m of hull length.

Petits navires — Mesurage et déclaration de la puissance — Partie 2: Propulsion électrique à usage marin

Le présent document spécifie les exigences liées à la détermination de la puissance des systèmes de propulsion électrique à usage marin lors de la documentation et de la vérification de la puissance (nominale) déclarée publiée par le fabricant. Le présent document s’applique aux systèmes électriques utilisés pour la propulsion de bateaux de plaisance et autres petits navires d’une longueur de coque maximale de 24 m.

General Information

• Status: Published
• Publication Date: 07-May-2024
• ICS: 47.080 - Small craft
• Technical Committee: ISO/TC 188 - Small craft
• Drafting Committee: ISO/TC 188 - Small craft
• Current Stage: 6060 - International Standard published
• Start Date: 08-May-2024
• Due Date: 01-Jun-2025
• Completion Date: 08-May-2024

Standards Content (Sample)

International
Standard
ISO 8665-2
First edition
Small craft — Power measurements
2024-05
and declarations —
Part 2:
Electric marine propulsion
Petits navires — Mesurage et déclaration de la puissance —
Partie 2: Propulsion électrique à usage marin
Reference number
ISO 8665-2:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 8665-2:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland

© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 8665-2:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Declaration of power . 2
4.1 General .2
4.2 Declaration of propeller shaft power .2
4.3 Declaration of motor power .2
5 Test methods . 2
5.1 Test conditions .2
5.2 Production conformity test/manufacturing tolerance .3
6 Test report . 3
Bibliography . 5

© ISO 2024 – All rights reserved
iii

---------------------- Page: 3 ----------------------
ISO 8665-2:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC
...

Norme
internationale
ISO 8665-2
Première édition
Petits navires — Mesurage et
2024-05
déclaration de la puissance —
Partie 2:
Propulsion électrique à usage marin
Small craft — Power measurements and declarations —
Part 2: Electric marine propulsion
Numéro de référence
ISO 8665-2:2024(fr) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 8665-2:2024(fr)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2024
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: [phone]
E-mail: [e-mail]
Web: www.iso.org
Publié en Suisse

© ISO 2024 – Tous droits réservés
ii

---------------------- Page: 2 ----------------------
ISO 8665-2:2024(fr)
Sommaire Page
Avant propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Déclaration de la puissance . 2
4.1 Généralités .2
4.2 Déclaration de la puissance de l’arbre d’hélice .2
4.3 Déclaration de la puissance du moteur .2
5 Méthodes d’essai . 2
5.1 Conditions d’essai . . .2
5.2 Essai de conformité de la production/tolérance de fabrication .3
6 Rapport d’essai . 3
Bibliographie . 5

© ISO 2024 – Tous droits réservés
iii

---------------------- Page: 3 ----------------------
ISO 8665-2:2024(fr)
Avant propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux
de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général
confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
L
...

FINAL DRAFT
International
Standard
ISO/FDIS 8665-2
ISO/TC 188
Small craft — Power measurements
Secretariat: SIS
and declarations —
Voting begins on:
2024-02-20
Part 2:
Electric marine propulsion
Voting terminates on:
2024-04-16
Petits navires — Mesurage et déclaration de la puissance —
Partie 2: Propulsion électrique à usage marin
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 8665-2:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO/FDIS 8665-2:2024(en)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 8665-2
ISO/TC 188
Small craft — Power measurements
Secretariat: SIS
and declarations —
Voting begins on:
Part 2:
Voting terminates on:
Electric marine propulsion
Petits navires — Mesurage et déclaration de la puissance —
Partie 2: Propulsion électrique à usage marin
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED TO
CP 401 • Ch. de Blandonnet 8
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
CH-1214 Vernier, Geneva
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
Phone: [phone]
DOCUMENTATION.
Email: [e-mail]
IN ADDITION TO THEIR EVALUATION AS
Website: www.iso.org Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 8665-2:2023(E)
Published in Switzerland
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON

OCCASION HAVE TO BE CONSIDERED IN THE
© ISO 2024 – All rights reserved
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023
ii

---------------------- Page: 2 ----------------------
ISO/FDIS 8665-2:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Declaration of power . 2
4.1 General . 2
4.2 Declaration of propeller shaft power . 2
4.3 Declaration of motor power . 2
5 Test methods . 2
5.1 Test conditions .
...

© ISO 2022 – All rights reserved
ISO/FDIS 8665--2:2023(E)
Date: 2023-09-26
ISO/TC 188/WG 5
Secretariat: SIS
Small craft — Power measurements and declarations — Part 2: Electric marine propulsion

FDIS stage

---------------------- Page: 1 ----------------------
© ISO 2022 – All rights reserved
First edition
Date: 2023-11-27

---------------------- Page: 2 ----------------------
ISO/FDIS 8665-2:2023(E)
© ISO 20222023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no
part of this publication may be reproduced or utilized otherwise in any form or by any means,
electronic or mechanical, including photocopying, or posting on the internet or an intranet, without
prior written permission. Permission can be requested from either ISO at the address below or
ISO’s member body in the country of the requester.
ISO Copyright Office
CP 401 • CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: [e-mail]
Website: www.iso.org
Published in Switzerland.
2 © ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/FDIS 8665-2:2023(E)
Contents
Foreword . 4
Introduction . 5
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Declaration of power . 2
4.1 General . 2
4.2 Declaration of propeller shaft power . 2
4.3 Declaration of motor power . 2
5 Test methods . 2
5.1 Test conditions . 2
5.2 Production conformity test/manufacturing tolerance . 3
6 Test report . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 5
Bibliography . 7
© ISO 2023 – All rights reserved iii

---------------------- Page: 4 ----------------------
ISO/FDIS 8665-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documentsdocument should be noted. This document was drafted in accordance
with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawnISO draws attention to the possibility that some of the elementsimplementation of this
document may beinvolve the subjectuse of (a) patent(s). ISO takes no position concerning the evidence,
validity or applicability of any claimed patent rights in respect thereof. As of the d
...