Alpine skis and bindings — Binding mounting area — Requirements and test methods

ISO 8364:2007 specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding - retention device - boot". It contains data for the manufacturer of alpine skis, bindings and retention devices, concerning dimensions, tests and other specifications for the binding mounting area.

Skis et fixations de skis alpins — Zone de montage de la fixation — Exigences de tenue et méthodes d'essai

L'ISO 8364:2007 spécifie les exigences et les méthodes d'essai relatives à la zone libre et à la zone de montage de la fixation de skis alpins, aux fixations elles-mêmes et aux dispositifs de retenue du ski, en vue d'assurer la compatibilité de l'ensemble fonctionnel «ski - fixation - dispositif de retenue - chaussure». L'ISO 8364:2007 donne au fabricant de skis alpins, de fixations et de dispositifs de retenue, des indications concernant les dimensions, les essais et autres spécifications relatives à la zone de montage.

Alpske smuči in varnostne vezi - Področje montaže varnostnih vezi - Zahteve in preskusne metode

Ta mednarodni standard določa zahteve in preskusne metode za področje montaže varnostnih vezi in področje prostega prostora, varnostne vezi za smuči vezi in varnostne naprave alpskih smuči zato, da bi se optimizirala združljivost funkcijske enote »varnostne vezi-varnostne naprave-čevlji«. Vsebuje podatke za proizvajalce alpskih smuči, varnostne vezi in varnostne naprave glede dimenzij, preskusov in drugih specifikacij za področje montaže varnostnih vezi.

General Information

Status
Withdrawn
Publication Date
12-Mar-2007
Withdrawal Date
12-Mar-2007
Current Stage
9599 - Withdrawal of International Standard
Completion Date
08-Dec-2017

Relations

Buy Standard

Standard
ISO 8364:2011
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 8364:2007 - Alpine skis and bindings -- Binding mounting area -- Requirements and test methods
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 8364:2011
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 8364:2007 - Skis et fixations de skis alpins -- Zone de montage de la fixation -- Exigences de tenue et méthodes d'essai
French language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 8364:2011
01-marec-2011
$OSVNHVPXþLLQYDUQRVWQHYH]L3RGURþMHPRQWDåHYDUQRVWQLKYH]L=DKWHYHLQ
SUHVNXVQHPHWRGH
Alpine skis and bindings -- Binding mounting area -- Requirements and test methods
Skis et fixations de skis alpins -- Zone de montage de la fixation -- Exigences de tenue et
méthodes d'essai
Ta slovenski standard je istoveten z: ISO 8364:2007
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
SIST ISO 8364:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 8364:2011

---------------------- Page: 2 ----------------------

SIST ISO 8364:2011

INTERNATIONAL ISO
STANDARD 8364
Fourth edition
2007-04-01

Alpine skis and bindings — Binding
mounting area — Requirements and test
methods
Skis et fixations de skis alpins — Zone de montage de la fixation —
Exigences de tenue et méthodes d'essai





Reference number
ISO 8364:2007(E)
©
ISO 2007

---------------------- Page: 3 ----------------------

SIST ISO 8364:2011
ISO 8364:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 8364:2011
ISO 8364:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Specifications of free space area. 2
4.1 Length of free space area (l ) . 2
z
4.2 Width of the free space area (b ) . 3
z
5 Geometrical requirements of free space area . 3
5.1 Longitudinal profile of the ski surface within the free space area . 3
5.2 Transverse profile of the ski surface within the free space area. 4
6 Specifications of binding mounting area . 4
6.1 Length of binding mounting area (l ). 4
b
6.2 Width of binding mounting area. 4
6.3 Minimum thickness of binding mounting area . 5
7 Strength requirements of binding mounting area. 5
7.1 Screw retention strength (F ). 5
r
7.2 Stripping resistance (F ) . 5
s
8 Specifications of the binding. 5
8.1 Centre-to-centre distances for binding mounting screws. 6
8.2 Penetration depth of binding screws. 6
9 Side walls. 6
10 Marking . 6
10.1 Marking of the mounting point . 6
10.2 Marking of the ski properties. 6
11 Apparatus . 7
11.1 Retention strength. 7
11.2 Stripping resistance . 8
12 Test screws . 8
13 Test methods. 8
13.1 Sampling and conditioning. 8
13.2 General requirements. 8
13.3 Retention strength test. 10
13.4 Stripping resistance test. 11
14 Test report . 12
Annex A (informative) Synoptic tables. 13

© ISO 2007 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 8364:2011
ISO 8364:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8364 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment,
Subcommittee SC 4, Skis and snowboards.
This fourth edition cancels and replaces the third edition (ISO 8364:1999), which has been technically revised.

iv © ISO 2007 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 8364:2011
INTERNATIONAL STANDARD ISO 8364:2007(E)

Alpine skis and bindings — Binding mounting area —
Requirements and test methods
1 Scope
This International Standard specifies requirements and test methods for the binding mounting area and free
space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the
functional unit "ski binding — retention device — boot".
It contains data for the manufacturer of alpine skis, bindings and retention devices, concerning dimensions,
tests and other specifications for the binding mounting area.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
ISO 5355, Alpine ski-boots — Requirements and test methods
ISO 6004:1991, Alpine skis — Ski binding screws — Requirements
ISO 6289, Skis — Vocabulary
ISO 6506:2005 (all parts), Metallic materials — Brinell hardness test
ISO 10045, Alpine skis — Binding mounting area — Requirements for test screws
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6289 and the following apply.
3.1
mounting point
location on the ski that indicates the position of the boot along the length of the ski for the purpose of mounting
the binding, and which corresponds to the boot sole mark established by ISO 5355 for alpine ski-boots
3.2
free space area
area forward and backward from the mounting point, fulfilling minimum flatness requirements in accordance
with Clause 5
See Figure 1.
© ISO 2007 – All rights reserved 1

---------------------- Page: 7 ----------------------

SIST ISO 8364:2011
ISO 8364:2007(E)
3.3
binding mounting area
area forward and backward from the mounting point, fulfilling minimum strength requirements in accordance
with Clause 7
See Figure 1.

Key
l length of binding mounting area
b
l length of free space area
z
b width of the free space area
z
a
Mounting point.
b
Free space area.
c
Binding mounting area (width in accordance with 6.2).
Figure 1 — Free space and binding mounting areas
4 Specifications of free space area
4.1 Length of free space area (l )
z
The length of the free space area forward and backward from the mounting point shall be according to the
values given in Table 1.
Table 1 — Length of free space area
Length of free space area forward and backward
from the mounting point
Group
mm
1 300
2 270
3 210
4 190


2 © ISO 2007 – All rights reserved

---------------------- Page: 8 ----------------------

SIST ISO 8364:2011
ISO 8364:2007(E)
4.2 Width of the free space area (b )
z
The minimum width of the free space area shall be as follows:
⎯ For Groups 1 and 2:
48 mm within an area 100 mm forward and 100 mm backward from the mounting point;
53 mm in the remaining part of the free space area.
⎯ For Group 3:
48 mm within an area 100 mm forward and 100 mm backward from the mounting point;
53 mm in the remaining part of the free space area.
⎯ For Group 4:
46 mm within an area 100 mm forward and 100 mm backward from the mounting point;
50 mm in the remaining part of the free space area.
5 Geometrical requirements of free space area
5.1 Longitudinal profile of the ski surface within the free space area
Deviations from the straightness of the longitudinal profile from a flat profile are only permissible in the form of
a constant curve in the length of the free space area; the tolerance on straightness in this area, the ski base
being pre
...

INTERNATIONAL ISO
STANDARD 8364
Fourth edition
2007-04-01

Alpine skis and bindings — Binding
mounting area — Requirements and test
methods
Skis et fixations de skis alpins — Zone de montage de la fixation —
Exigences de tenue et méthodes d'essai





Reference number
ISO 8364:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 8364:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8364:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Specifications of free space area. 2
4.1 Length of free space area (l ) . 2
z
4.2 Width of the free space area (b ) . 3
z
5 Geometrical requirements of free space area . 3
5.1 Longitudinal profile of the ski surface within the free space area . 3
5.2 Transverse profile of the ski surface within the free space area. 4
6 Specifications of binding mounting area . 4
6.1 Length of binding mounting area (l ). 4
b
6.2 Width of binding mounting area. 4
6.3 Minimum thickness of binding mounting area . 5
7 Strength requirements of binding mounting area. 5
7.1 Screw retention strength (F ). 5
r
7.2 Stripping resistance (F ) . 5
s
8 Specifications of the binding. 5
8.1 Centre-to-centre distances for binding mounting screws. 6
8.2 Penetration depth of binding screws. 6
9 Side walls. 6
10 Marking . 6
10.1 Marking of the mounting point . 6
10.2 Marking of the ski properties. 6
11 Apparatus . 7
11.1 Retention strength. 7
11.2 Stripping resistance . 8
12 Test screws . 8
13 Test methods. 8
13.1 Sampling and conditioning. 8
13.2 General requirements. 8
13.3 Retention strength test. 10
13.4 Stripping resistance test. 11
14 Test report . 12
Annex A (informative) Synoptic tables. 13

© ISO 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 8364:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8364 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment,
Subcommittee SC 4, Skis and snowboards.
This fourth edition cancels and replaces the third edition (ISO 8364:1999), which has been technically revised.

iv © ISO 2007 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 8364:2007(E)

Alpine skis and bindings — Binding mounting area —
Requirements and test methods
1 Scope
This International Standard specifies requirements and test methods for the binding mounting area and free
space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the
functional unit "ski binding — retention device — boot".
It contains data for the manufacturer of alpine skis, bindings and retention devices, concerning dimensions,
tests and other specifications for the binding mounting area.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
ISO 5355, Alpine ski-boots — Requirements and test methods
ISO 6004:1991, Alpine skis — Ski binding screws — Requirements
ISO 6289, Skis — Vocabulary
ISO 6506:2005 (all parts), Metallic materials — Brinell hardness test
ISO 10045, Alpine skis — Binding mounting area — Requirements for test screws
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6289 and the following apply.
3.1
mounting point
location on the ski that indicates the position of the boot along the length of the ski for the purpose of mounting
the binding, and which corresponds to the boot sole mark established by ISO 5355 for alpine ski-boots
3.2
free space area
area forward and backward from the mounting point, fulfilling minimum flatness requirements in accordance
with Clause 5
See Figure 1.
© ISO 2007 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 8364:2007(E)
3.3
binding mounting area
area forward and backward from the mounting point, fulfilling minimum strength requirements in accordance
with Clause 7
See Figure 1.

Key
l length of binding mounting area
b
l length of free space area
z
b width of the free space area
z
a
Mounting point.
b
Free space area.
c
Binding mounting area (width in accordance with 6.2).
Figure 1 — Free space and binding mounting areas
4 Specifications of free space area
4.1 Length of free space area (l )
z
The length of the free space area forward and backward from the mounting point shall be according to the
values given in Table 1.
Table 1 — Length of free space area
Length of free space area forward and backward
from the mounting point
Group
mm
1 300
2 270
3 210
4 190


2 © ISO 2007 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 8364:2007(E)
4.2 Width of the free space area (b )
z
The minimum width of the free space area shall be as follows:
⎯ For Groups 1 and 2:
48 mm within an area 100 mm forward and 100 mm backward from the mounting point;
53 mm in the remaining part of the free space area.
⎯ For Group 3:
48 mm within an area 100 mm forward and 100 mm backward from the mounting point;
53 mm in the remaining part of the free space area.
⎯ For Group 4:
46 mm within an area 100 mm forward and 100 mm backward from the mounting point;
50 mm in the remaining part of the free space area.
5 Geometrical requirements of free space area
5.1 Longitudinal profile of the ski surface within the free space area
Deviations from the straightness of the longitudinal profile from a flat profile are only permissible in the form of
a constant curve in the length of the free space area; the tolerance on straightness in this area, the ski base
being pressed against a flat surface, is as follows (see Figure 2):
⎯ Groups 1 and 2: 5 mm;
⎯ Groups 3 and 4: 4 mm.
Tolerance in millimetres

Key
l length of free space area
z
a
Groups 1 and 2.
b
Groups 3 and 4.
Figure 2 — Longitudinal profile of the surface

Outside the binding mounting area, within the length of the free space area, a maximum downward deviation
of 2 mm from the constant curve is
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Skis et fixations de skis alpins -- Zone de montage de la fixation -- Exigences de tenue et méthodes d'essaiAlpine skis and bindings -- Binding mounting area -- Requirements and test methods97.220.20Oprema za zimske športeWinter sports equipmentICS:Ta slovenski standard je istoveten z:ISO 8364:2007oSIST ISO 8364:2011en01-januar-2011oSIST ISO 8364:2011SLOVENSKI
STANDARD



oSIST ISO 8364:2011



Reference numberISO 8364:2007(E)© ISO 2007
INTERNATIONAL STANDARD ISO8364Fourth edition2007-04-01Alpine skis and bindings — Binding mounting area — Requirements and test methods Skis et fixations de skis alpins — Zone de montage de la fixation — Exigences de tenue et méthodes d'essai
oSIST ISO 8364:2011



ISO 8364:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2007 – All rights reserved
oSIST ISO 8364:2011



ISO 8364:2007(E) © ISO 2007 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Specifications of free space area.2 4.1 Length of free space area (lz).2 4.2 Width of the free space area (bz).3 5 Geometrical requirements of free space area.3 5.1 Longitudinal profile of the ski surface within the free space area.3 5.2 Transverse profile of the ski surface within the free space area.4 6 Specifications of binding mounting area.4 6.1 Length of binding mounting area (lb).4 6.2 Width of binding mounting area.4 6.3 Minimum thickness of binding mounting area.5 7 Strength requirements of binding mounting area.5 7.1 Screw retention strength (Fr).5 7.2 Stripping resistance (Fs).5 8 Specifications of the binding.5 8.1 Centre-to-centre distances for binding mounting screws.6 8.2 Penetration depth of binding screws.6 9 Side walls.6 10 Marking.6 10.1 Marking of the mounting point.6 10.2 Marking of the ski properties.6 11 Apparatus.7 11.1 Retention strength.7 11.2 Stripping resistance.8 12 Test screws.8 13 Test methods.8 13.1 Sampling and conditioning.8 13.2 General requirements.8 13.3 Retention strength test.10 13.4 Stripping resistance test.11 14 Test report.12 Annex A (informative)
Synoptic tables.13
oSIST ISO 8364:2011



ISO 8364:2007(E) iv © ISO 2007 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8364 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment, Subcommittee SC 4, Skis and snowboards. This fourth edition cancels and replaces the third edition (ISO 8364:1999), which has been technically revised.
oSIST ISO 8364:2011



INTERNATIONAL STANDARD ISO 8364:2007(E) © ISO 2007 – All rights reserved 1Alpine skis and bindings — Binding mounting area — Requirements and test methods 1 Scope This International Standard specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding — retention device — boot". It contains data for the manufacturer of alpine skis, bindings and retention devices, concerning dimensions, tests and other specifications for the binding mounting area. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters ISO 5355, Alpine ski-boots — Requirements and test methods ISO 6004:1991, Alpine skis — Ski binding screws — Requirements ISO 6289, Skis — Vocabulary ISO 6506:2005 (all parts), Metallic materials — Brinell hardness test ISO 10045, Alpine skis — Binding mounting area — Requirements for test screws 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6289 and the following apply. 3.1 mounting point location on the ski that indicates the position of the boot along the length of the ski for the purpose of mounting the binding, and which corresponds to the boot sole mark established by ISO 5355 for alpine ski-boots 3.2 free space area area forward and backward from the mounting point, fulfilling minimum flatness requirements in accordance with Clause 5 See Figure 1. oSIST ISO 8364:2011



ISO 8364:2007(E) 2 © ISO 2007 – All rights reserved 3.3 binding mounting area area forward and backward from the mounting point, fulfilling minimum strength requirements in accordance with Clause 7 See Figure 1.
Key lb length of binding mounting area lz length of free space area bz width of the free space area a Mounting point. b Free space area. c Binding mounting area (width in accordance with 6.2). Figure 1 — Free space and binding mounting areas 4 Specifications of free space area 4.1 Length of free space area (lz) The length of the free space area forward and backward from the mounting point shall be according to the values given in Table 1. Table 1 — Length of free space area Group Length of free space area forward and backward from the mounting point mm 1 300 2 270 3 210 4 190
oSIST ISO 8364:2011



ISO 8364:2007(E) © ISO 2007 – All rights reserved 34.2 Width of the free space area (bz) The minimum width of the free space area shall be as follows: ⎯ For Groups 1 and 2: 48 mm within an area 100 mm forward and 100 mm backward from the mounting point; 53 mm in the remaining part of the free space area. ⎯ For Group 3: 48 mm within an area 100 mm forward and 100 mm backward from the mounting point; 53 mm in the remaining part of the free space area. ⎯ For Group 4: 46 mm within an area 100 mm forward and 100 mm backward from the mounting point; 50 mm in the remaining part of the free space area. 5 Geometrical requirements of free space area 5.1 Longitudinal profile of the ski surface within the free space area Deviations from the straightness of the longitudinal profile from a flat profile are only permissible in the form of a constant curve in the length of the free
...

NORME ISO
INTERNATIONALE 8364
Quatrième édition
2007-04-01

Skis et fixations de skis alpins — Zone de
montage de la fixation — Exigences de
tenue et méthodes d'essai
Alpine skis and bindings — Binding mounting area — Requirements
and test methods





Numéro de référence
ISO 8364:2007(F)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 8364:2007(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


©  ISO 2007
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2007 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 8364:2007(F)
Sommaire Page
Avant-propos. iv
1 Domaine d'application. 1
2 Références normatives . 1
3 Termes et définitions. 1
4 Spécifications relatives à la zone libre. 2
4.1 Longueur de la zone libre (l ) . 2
z
4.2 Largeur de la zone libre (b ). 3
z
5 Exigences géométriques de la zone libre . 3
5.1 Profil longitudinal de la surface du ski dans la zone libre . 3
5.2 Profil transversal de la surface du ski dans la zone libre. 4
6 Spécifications relatives à la zone de montage de la fixation . 4
6.1 Longueur de la zone de montage de la fixation (l ) . 4
b
6.2 Largeur de la zone de montage de la fixation (l ). 4
b
6.3 Épaisseur minimale de la zone de montage de la fixation . 5
7 Exigences de résistance de la zone de montage de la fixation . 5
7.1 Résistance des vis à l'arrachement (F ) . 5
r
7.2 Résistance au foirage du ski (F ) . 5
s
8 Spécifications relatives à la fixation. 6
8.1 Entraxe des vis de fixation . 6
8.2 Profondeur de pénétration des vis de montage . 6
9 Chants du ski . 6
10 Marquage . 6
10.1 Marquage du point de montage . 6
10.2 Marquage des propriétés du ski. 7
11 Appareillage . 7
11.1 Résistance à l'arrachement . 7
11.2 Résistance au foirage. 8
12 Vis d'essai. 8
13 Méthodes d'essai . 8
13.1 Échantillonnage et conditionnement. 8
13.2 Exigences générales . 8
13.3 Essai de résistance à l'arrachement. 10
13.4 Essai de résistance au foirage . 11
14 Rapport d'essai . 12
Annexe A (informative) Tableaux synoptiques . 13

© ISO 2007 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 8364:2007(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 8364 a été élaborée par le comité technique ISO/TC 83, Matériel de sports et d'activités de plein air,
sous-comité SC 4, Skis et surfs.
Cette quatrième édition annule et remplace la troisième édition (ISO 8364:1999), qui a fait l'objet d'une
révision technique.

iv © ISO 2007 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 8364:2007(F)

Skis et fixations de skis alpins — Zone de montage de la
fixation — Exigences de tenue et méthodes d'essai
1 Domaine d'application
La présente Norme internationale spécifie les exigences et les méthodes d'essai relatives à la zone libre et à
la zone de montage de la fixation de skis alpins, aux fixations elles-mêmes et aux dispositifs de retenue du ski,
en vue d'assurer la compatibilité de l'ensemble fonctionnel «ski – fixation – dispositif de retenue – chaussure».
Elle donne au fabricant de skis alpins, de fixations et de dispositifs de retenue, des indications concernant les
dimensions, les essais et autres spécifications relatives à la zone de montage.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 4287:1997, Spécification géométrique des produits (GPS) — État de surface: Méthode du profil —
Termes, définitions et paramètres d'état de surface
ISO 5355, Chaussures de ski pour skis alpins — Exigences et méthodes d'essai
ISO 6004:1991, Skis alpins — Vis de fixation de skis — Spécifications
ISO 6289, Skis — Vocabulaire
ISO 6506:2005 (toutes les parties), Matériaux métalliques — Essai de dureté Brinell
ISO 10045, Skis alpins — Zone de montage de la fixation — Spécifications des vis d'essai
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 6289 ainsi que les
suivants s'appliquent.
3.1
point de montage
emplacement sur le ski qui indique la position de la chaussure sur la longueur du ski en vue du montage de la
fixation; le point de montage correspond à la marque de la semelle de chaussure établie dans l'ISO 5355 pour
les chaussures de skis alpins
3.2
zone libre
zone située à l'avant et à l'arrière du point de montage et répondant aux exigences minimales de planéité,
conformément à l'Article 5
Voir Figure 1.
© ISO 2007 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 8364:2007(F)
3.3
zone de montage de la fixation
zone située à l'avant et à l'arrière du point de montage et répondant aux exigences minimales en matière de
résistance et de géométrie conformément à l'Article 7
Voir Figure 1.

Légende
l longueur de la zone de montage de la fixation
b
l longueur de la zone libre
z
b largeur de la zone libre
z
a
Point de montage.
b
Zone libre.
c
Zone de montage de la fixation (largeur conforme à 6.2).
Figure 1 — Zone libre et zone de montage de la fixation
4 Spécifications relatives à la zone libre
4.1 Longueur de la zone libre (l )
z
La longueur de la zone libre à l'avant et à l'arrière du point de montage doit être conforme aux valeurs
données dans le Tableau 1.
Tableau 1 — Longueur de la zone libre
Longueur de la zone libre à l'avant et à l'arrière
du point de montage
Groupe
mm
1 300
2 270
3 210
4 190

2 © ISO 2007 – Tous droits réservés

---------------------- Page: 6 ----------------------
ISO 8364:2007(F)
4.2 Largeur de la zone libre (b )
z
La largeur minimale de la zone libre doit être la suivante:
⎯ Pour les Groupes 1 et 2:
48 mm dans une zone de 100 mm en avant et 100 mm en arrière du point de montage;
53 mm dans la partie restante de la zone libre.
⎯ Pour le Groupe 3:
48 mm dans une zone de 100 mm en avant et 100 mm en arrière du point de montage;
53 mm dans la partie restante de la zone libre.
⎯ Pour le Groupe 4:
46 mm dans une zone de 100 mm en avant et 100 mm en arrière du point de montage;
50 mm dans la partie restante de la zone libre.
5 Exigences géométriques de la zone libre
5.1 Profil longitudinal de la surface du ski dans la zone libre
Les écarts de rectitude du profil longitudinal par rapport à un profil plat ne sont admissibles que sous forme de
courbe constante dans la longueur de la zone libre; la base du ski étant appuyée sur une surface plane, la
tolérance de rectitude dans cette zone (voir Figure 2) est la suivante:
⎯ Groupes 1 et 2: 5 mm;
⎯ Groupes 3 et 4: 4 mm.
Tolérances en millimètres

Légende
l longueur de la zone libre
z
a
Groupes 1 et 2.
b
Groupes 3 et 4.
Figure 2 — Profil longitudinal de la surface

À l'extérieur de la zone de montage de la fixation, un écart maximal de 2 mm est admissible vers le bas par
rapport à la courbe constante sur la longueur de l'espace libre.
© ISO 2007 – Tous droits réservés 3

---------------------- Page: 7 ----------------------
ISO 8364:2007(F)
5.2
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.