ISO 14824-2:2012
(Main)Grout for prestressing tendons — Part 2: Grouting procedures
Grout for prestressing tendons — Part 2: Grouting procedures
This part of ISO 14824 gives the procedures to be used for grouting of tendons in post-tensioned prestressed concrete. It is applicable to all types of structures, including bridges and buildings. This part of ISO 14824 also covers suitability testing and inspection testing for grouts and their component materials used on a project.
Coulis pour câbles de précontrainte — Partie 2: Modes opératoires de gobetage
Injekcijska masa za prednapete kable - 2. del: Postopki injektiranja
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 14824-2
First edition
2012-10-01
Grout for prestressing tendons —
Part 2:
Grouting procedures
Coulis pour câbles de précontrainte —
Partie 2: Modes opératoires de gobetage
Reference number
ISO 14824-2:2012(E)
©
ISO 2012
---------------------- Page: 1 ----------------------
ISO 14824-2:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14824-2:2012(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Documentation . 1
4.1 Execution specification . 1
4.2 Quality plan . 2
4.3 Execution documentation. 2
5 Materials . 2
6 Grout assessment . 3
6.1 Suitability testing . 3
6.2 Project specific grouting tests . 3
7 Equipment . 4
7.1 General . 4
7.2 Mixer . 4
7.3 Pump . 4
7.4 Hoses . 4
7.5 Inlet connections .
...
SLOVENSKI STANDARD
oSIST ISO/DIS 14824-2:2012
01-junij-2012
Injekcijska masa za prednapete kable - 2. del: Postopki injektiranja
Grout for prestressing tendons - Part 2: Grouting procedures
Coulis pour câbles de précontrainte - Partie 2: Modes opératoires de gobetage
Ta slovenski standard je istoveten z: ISO/FDIS 14824-2
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
oSIST ISO/DIS 14824-2:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST ISO/DIS 14824-2:2012
---------------------- Page: 2 ----------------------
oSIST ISO/DIS 14824-2:2012
DRAFT INTERNATIONAL STANDARD ISO/DIS 14824-2
ISO/TC 71/SC 3 Secretariat: SN
Voting begins on Voting terminates on
2011-06-29 2011-11-29
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Grout for prestressing tendons —
Part 2:
Grouting procedures
Coulis pour câbles de précontrainte —
Partie 2: Modes opératoires de gobetage
ICS 91.100.30
In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est
distribué en version anglaise seulement.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2011
---------------------- Page: 3 ----------------------
oSIST ISO/DIS 14824-2:2012
ISO/DIS 14824-2
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2011 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST ISO/DIS 14824-2:2012
---------------------- Page: 5 ----------------------
oSIST ISO/DIS 14824-2:2012
ISO/CD 14824-2 (E)
Contents Page
Foreword� . 3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Documentation .5
4.1 Execution specification .5
4.2 Quality plan .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.