ISO 877-2:2025
(Main)Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure behind window glass
Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure behind window glass
This document specifies a method for the direct exposure of plastics to solar radiation (method A) and a method for the exposure of plastics to glass-filtered solar radiation (exposure behind window glass) (method B). The purpose is to assess property changes produced after specified stages of such exposures. General guidance concerning the scope of the ISO 877 series[ REF Reference_ref_2 \r \h 1 08D0C9EA79F9BACE118C8200AA004BA90B0200000008000000100000005200650066006500720065006E00630065005F007200650066005F0032000000 ] is given in ISO 877-1.
Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 2: Exposition directe et exposition derrière une vitre en verre
Le présent document spécifie une méthode d’exposition directe des plastiques au rayonnement solaire (méthode A) et une méthode d’exposition des plastiques au rayonnement solaire sous filtre de verre (exposition derrière une vitre en verre) (méthode B). L’objectif consiste à évaluer les changements de propriété produits après des phases d’exposition spécifiées. Des lignes directrices générales relatives au domaine d’application de la série ISO 877 [ REF Reference_ref_2 \r \h 1 08D0C9EA79F9BACE118C8200AA004BA90B0200000008000000100000005200650066006500720065006E00630065005F007200650066005F0032000000 ] sont données dans l’ISO 877-1.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 877-2
Second edition
Plastics — Methods of exposure to
2025-07
solar radiation —
Part 2:
Direct weathering and exposure
behind window glass
Plastiques — Méthodes d'exposition au rayonnement solaire —
Partie 2: Exposition directe et exposition derrière une vitre en verre
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
5.1 General requirements .1
5.2 Test fixture for exposures using method A .2
5.3 Test fixture for exposures using method B .2
5.4 Apparatus for measurement of climatic factors .3
6 Test specimens . 3
7 Conditions of exposure of the test specimens . 4
7.1 Exposure aspect .4
7.2 Exposure site.4
8 Exposure stages . 4
8.1 General .4
8.2 Duration of exposure .4
8.3 Solar radiant exposure .5
9 Procedure . 5
9.1 Mounting of test specimens .5
9.1.1 General .5
9.1.2 Method A . . .5
9.1.3 Method B .5
9.2 Mounting of reference materials (if used) .5
9.3 Climatic observations .5
9.4 Exposure of test specimens .5
9.4.1 General .5
9.4.2 Method A . . .5
9.4.3 Method B . .5
9.5 Determination of changes in properties .6
10 Expression of results . 6
10.1 Determination of changes in properties .6
10.2 Climatic conditions .6
11 Test report . 6
Bibliography . 7
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee Technical Committee ISO/TC 61, Plastics, SC 6, Ageing,
chemical and environmental resistance, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 877-2:2009), which has been technically
revised.
The main changes are as follows:
— addition of a requirement for the area beneath and in the vicinity of racks in 5.1;
— clarification that no shadow of nearby objects shall fall on the specimens in 7.2;
— addition of Bibliography to include reference from 5.3, NOTE 2;
— deletion of NOTE in 5.4.
A list of all parts in the ISO 877 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 877-2:2025(en)
Plastics — Methods of exposure to solar radiation —
Part 2:
Direct weathering and exposure behind window glass
1 Scope
This document specifies a method for the direct exposure of plastics to solar radiation (method A) and a
method for the exposure of plastics to glass-filtered solar radiation (exposure behind window glass)
(method B). The purpose is to assess property changes produced after specified stages of such exposures.
[1]
General guidance concerning the scope of the ISO 877 series is given in ISO 877-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 877-1:2025, Plastics — Methods of exposure to solar radiation — Part 1: General guidance
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org
4 Principle
General guidance is given in ISO 877-1:2025, Clause 4.
5 Apparatus
5.1 General requirements
Refer to ISO 877-1:2025, 5.1, for general requirements.
When installed, the racks employed in test methods A and B shall be capable of providing the desired angle of
inclination (see 7.1) and shall be such that no portion of any test specimen is closer than 0,5 m to the ground
or to any other obstruction. Specimens may be mounted directly on the rack or in suitable holders which are
then affixed to the rack. Mounting fixtures shall be secure, but shall apply as little stress as possible to the
specimens and shall permit shrinkage, expansion or warping to occur without constraint, as far as possible.
The area beneath and in the vicinity of the racks shall be characterized by low reflectance and by ground
cover typical of that climatological area. In desert areas, the racks shall be located on gravel, in most
temperate areas on low-cut grass. Other ground covers may be used with the agreement of all parties and
shall be included in the test report.
NOTE The use of other ground covers can affect test results.
In some cases, the object to be exposed is intended to be in direct contact with the ground (e.g. when entire
vehicles are exposed). In these cases, the requirements for minimum distance between the specimens and
the ground do not apply.
5.2 Test fixture for exposures using method A
The design of the specimen rack shall be suited to the types of specimens being exposed, but for many
purposes a flat frame mounted on a support is suitable.
...
Norme
internationale
ISO 877-2
Deuxième édition
Plastiques — Méthodes d'exposition
2025-07
au rayonnement solaire —
Partie 2:
Exposition directe et exposition
derrière une vitre en verre
Plastics — Methods of exposure to solar radiation —
Part 2: Direct weathering and exposure behind window glass
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2025
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 1
5 Appareillage . 1
5.1 Exigences générales .1
5.2 Dispositif de fixation pour les essais d’exposition réalisés selon la méthode A .2
5.3 Dispositif de fixation pour les essais d’exposition réalisés selon la méthode B .2
5.4 Appareillage pour le mesurage des facteurs climatiques .3
6 Éprouvettes. 3
7 Conditions d’exposition des éprouvettes . 4
7.1 Aspect de l’exposition .4
7.2 Site d’exposition.4
8 Phases d’exposition . 4
8.1 Généralités .4
8.2 Durée de l’exposition.4
8.3 Exposition énergétique solaire .5
9 Mode opératoire . 5
9.1 Montage des éprouvettes .5
9.1.1 Généralités .5
9.1.2 Méthode A .5
9.1.3 Méthode B .5
9.2 Montage des matériaux de référence (s’ils sont utilisés) .5
9.3 Observations climatiques .5
9.4 Exposition des éprouvettes .5
9.4.1 Généralités .5
9.4.2 Méthode A .5
9.4.3 Méthode B .6
9.5 Détermination des modifications de propriétés .6
10 Expression des résultats . 6
10.1 Détermination des modifications de propriétés .6
10.2 Conditions climatiques .6
11 Rapport d’essai . 6
Bibliographie . 7
iii
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux
de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général
confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de brevet revendiqué à cet égard. À la date de publication du présent document, l’ISO n’avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l’adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de
l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 6,
Vieillissement et résistance aux agents chimiques et environnants, en collaboration avec le comité technique
CEN/TC 249, Plastiques, du Comité européen de normalisation (CEN), conformément à l’Accord de
coopération technique entre l’ISO et le CEN (Accord de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 877-2:2009), qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes:
— ajout d’une exigence concernant la zone sous et à proximité des supports en 5.1;
— indication que l’ombre des objets à proximité ne doit pas tomber sur les éprouvettes en 7.2;
— ajout de la Bibliographie pour inclure une référence citée en 5.3, NOTE 2;
— suppression de la NOTE en 5.4.
Une liste de toutes les parties de la série ISO 877 se trouve sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/fr/members.html.
iv
Norme internationale ISO 877-2:2025(fr)
Plastiques — Méthodes d'exposition au rayonnement
solaire —
Partie 2:
Exposition directe et exposition derrière une vitre en verre
1 Domaine d’application
Le présent document spécifie une méthode d’exposition directe des plastiques au rayonnement solaire
(méthode A) et une méthode d’exposition des plastiques au rayonnement solaire sous filtre de verre
(exposition derrière une vitre en verre) (méthode B). L’objectif consiste à évaluer les changements de
propriété produits après des phases d’exposition spécifiées.
[1]
Des lignes directrices générales relatives au domaine d’application de la série ISO 877 sont données dans
l’ISO 877-1.
2 Références normatives
Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu, des exigences du
présent document. Pour les références datées, seule l’édition citée s’applique. Pour les références non datées,
la dernière édition du document de référence s’applique (y compris les éventuels amendements).
ISO 877-1:2025, Plastiques — Méthodes d’exposition au rayonnement solaire — Partie 1: Lignes directrices
générales
3 Termes et définitions
Aucun terme n’est défini dans le présent document.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en normalisation,
consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse https:// www .electropedia .org
4 Principe
Des lignes directrices générales sont données à l'ISO 877-1:2025, l’Article 4.
5 Appareillage
5.1 Exigences générales
Pour les exigences générales, se référer au l'ISO 877-1:2025, 5.1.
Une fois installés, les supports utilisés pour les méthodes d’essai A et B doivent permettre d’obtenir l’angle
d’inclinaison voulu (voir 7.1) et doivent être conçus de sorte qu’aucune partie de l’éprouvette ne se trouve à
moins de 0,5 m du sol ou de tout autre obstacle. Les éprouvettes peuvent être montées directement sur le
support d’essai aux intempéries ou dans des porte-éprouvettes appropriés, eux-mêmes fixés au support. Les
dispositifs de fixation doivent être sûrs, mais doivent exercer une contrainte aussi faible que possible sur les
éprouvettes et doivent permettre autant que possible que des phénomènes éventuels de retrait, de dilatation
ou de gauchissement se produisent sans contrainte.
La zone sous et à proximité des supports doit être caractérisée par une faible réflexion et par une
couverture végétale caractéristique de la zone climatologique
...
FINAL DRAFT
International
Standard
ISO/FDIS 877-2
ISO/TC 61/SC 6
Plastics — Methods of exposure to
Secretariat: DIN
solar radiation —
Voting begins on:
2025-05-07
Part 2:
Direct weathering and exposure
Voting terminates on:
2025-07-02
behind window glass
Plastiques — Méthodes d'exposition au rayonnement solaire —
Partie 2: Exposition directe et exposition derrière une vitre en
verre
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 877-2:2025(en) © ISO 2025
FINAL DRAFT
ISO/FDIS 877-2:2025(en)
International
Standard
ISO/FDIS 877-2
ISO/TC 61/SC 6
Plastics — Methods of exposure to
Secretariat: DIN
solar radiation —
Voting begins on:
Part 2:
Direct weathering and exposure
Voting terminates on:
behind window glass
Plastiques — Méthodes d'exposition au rayonnement solaire —
Partie 2: Exposition directe et exposition derrière une vitre en verre
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 877-2:2025(en) © ISO 2025
ii
ISO/FDIS 877-2:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
5.1 General requirements .1
5.2 Test fixture for exposures using method A .2
5.3 Test fixture for exposures using method B .2
5.4 Apparatus for measurement of climatic factors .3
6 Test specimens . 3
7 Conditions of exposure of the test specimens . 4
7.1 Exposure aspect .4
7.2 Exposure site.4
8 Exposure stages . 4
8.1 General .4
8.2 Duration of exposure .4
8.3 Solar radiant exposure .5
9 Procedure . 5
9.1 Mounting of test specimens .5
9.1.1 General .5
9.1.2 Method A . . .5
9.1.3 Method B .5
9.2 Mounting of reference materials (if used) .5
9.3 Climatic observations .5
9.4 Exposure of test specimens .5
9.4.1 General .5
9.4.2 Method A . . .5
9.4.3 Method B . .5
9.5 Determination of changes in properties .6
10 Expression of results . 6
10.1 Determination of changes in properties .6
10.2 Climatic conditions .6
11 Test report . 6
Bibliography . 7
iii
ISO/FDIS 877-2:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee Technical Committee ISO/TC 61, Plastics, SC 6, Ageing,
chemical and environmental resistance, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 877-2:2009), which has been technically
revised.
The main changes are as follows:
— addition of a requirement for the area beneath and in the vicinity of racks in 5.1;
— clarification that no shadow of nearby objects shall fall on the specimens in 7.2;
— addition of Bibliography to include reference from 5.3, NOTE 2;
— deletion of NOTE in 5.4.
A list of all parts in the ISO 877 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
FINAL DRAFT International Standard ISO/FDIS 877-2:2025(en)
Plastics — Methods of exposure to solar radiation —
Part 2:
Direct weathering and exposure behind window glass
1 Scope
This document specifies a method for the direct exposure of plastics to solar radiation (method A) and a
method for the exposure of plastics to glass-filtered solar radiation (exposure behind window glass)
(method B). The purpose is to assess property changes produced after specified stages of such exposures.
[1]
General guidance concerning the scope of the ISO 877 series is given in ISO 877-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
1)
ISO 877-1:— , Plastics — Methods of exposure to solar radiation — Part 1: General guidance
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org
4 Principle
General guidance is given in ISO 877-1:—, Clause 4.
5 Apparatus
5.1 General requirements
Refer to ISO 877-1:2025,
...
Style Definition: Heading 1: Indent: Left: 0 cm, First
ISO/FDIS 877-2
line: 0 cm
ISO/TC 61/SC 6
Style Definition: Heading 2: Indent: Left: 0 cm, First
line: 0 cm
Secretariat: DIN
Style Definition: Heading 3: Indent: Left: 0 cm, First
line: 0 cm
Date: 2025-01-2304-22
Style Definition: Heading 4: Indent: Left: 0 cm, First
line: 0 cm
Style Definition: Heading 5: Indent: Left: 0 cm, First
line: 0 cm
Style Definition: Heading 6
Style Definition: List Continue 1
Plastics — Methods of exposure to solar radiation —
Style Definition: p2: Font: 12 pt, Bold, (Asian) Japanese,
(Other) Dutch (Netherlands), Level 2, Indent: Left: 0 cm,
First line: 0 cm, Space Before: 3 pt, Line spacing:
Exactly 12.5 pt, Outline numbered + Level: 2 +
Numbering Style: 1, 2, 3, … + Start at: 1 + Alignment:
Left + Aligned at: 0 cm + Indent at: 1.02 cm, Don't
hyphenate, Tab stops: 1.23 cm, Left
Style Definition: p3: Font: Bold, (Asian) Japanese,
Part 2:
(Other) Dutch (Netherlands), Level 3, Indent: Left: 0 cm,
Direct weathering and exposure behind window glass
First line: 0 cm, Space Before: 3 pt, Line spacing:
Exactly 11.5 pt, Outline numbered + Level: 3 +
Plastiques — Méthodes d'exposition au rayonnement solaire —
Numbering Style: 1, 2, 3, … + Start at: 1 + Alignment:
Left + Aligned at: 0 cm + Indent at: 1.27 cm, Don't
Partie 2: Exposition directe et exposition derrière une vitre en verre
hyphenate, Tab stops: 1.55 cm, Left
Style Definition: p4: Font: Bold, (Asian) Japanese,
(Other) Dutch (Netherlands), Level 4, Indent: Left: 0 cm,
First line: 0 cm, Space Before: 3 pt, Line spacing:
Exactly 11.5 pt, Outline numbered + Level: 4 +
Numbering Style: 1, 2, 3, … + Start at: 1 + Alignment:
Left + Aligned at: 0 cm + Indent at: 1.52 cm, Don't
hyphenate, Tab stops: 1.66 cm, Left + 2.01 cm, Left +
2.4 cm, Left
Style Definition
...
Style Definition
...
FDIS stage
Style Definition: Body Text
Style Definition: boxedText
Style Definition: Boxed List Continue 1
Style Definition: boxedTitle
Style Definition: FooterCentered
Style Definition: FooterPageNumber
Style Definition: FooterPageRomanNumber
Style Definition: FooterCenteredContinued
Style Definition: TPS Markup Base
Formatted: French (Switzerland)
ISO/FDIS 877-2:2025(en)
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Formatted: French (Switzerland)
E-mail: copyright@iso.org
Website: www.iso.org
Formatted: English (United Kingdom)
Formatted: English (United Kingdom)
Published in Switzerland
Formatted: Hyperlink
Field Code Changed
Formatted: English (United Kingdom)
ii
ISO/FDIS 877-2:2025(en)
Contents
Foreword . iv
Part 2: Direct weathering and exposure behind window glass . 1
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
5.1 General requirements . 1
5.2 Test fixture for exposures using method A . 2
5.3 Test fixture for exposures using method B . 2
5.4 Apparatus for measurement of climatic factors . 3
6 Test specimens . 3
7 Conditions of exposure of the test specimens . 4
7.1 Exposure aspect . 4
7.2 Exposure site . 4
8 Exposure stages . 4
8.1 General . 4
8.2 Duration of exposure . 4
8.3 Solar radiant exposure . 5
9 Procedure . 5
9.1 Mounting of test specimens . 5
9.1.1 General . 5
9.1.2 Method A . 5
9.1.3 Method B . 5
9.2 Mounting of reference materials (if used) . 5
9.3 Climatic observations . 5
9.4 Exposure of test specimens . 5
9.4.1 General . 5
9.4.2 Method A . 5
9.4.3 Method B . 5
9.5 Determination of changes in properties . 6
10 Expression of results . 6
10.1 Determination of changes in properties . 6
10.2 Climatic conditions . 6
11 Test report . 6
Bibliography . 7
Foreword . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
iii
ISO/FDIS 877-2:2025(en)
6 Test specimens . 4
7 Conditions of exposure of the test specimens . 4
8 Exposure stages . 5
9 Procedure . 5
10 Expression of results . 6
11 Test report . 6
Bibliography . 7
iv
ISO/FDIS 877-2:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Formatted: English (United Kingdom)
Formatted: English (United Kingdom)
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for identifying any or all such
patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.htmlwww.iso.org/iso/foreword.html.
Formatted: English (United Kingdom)
This document was prepared by Technical Committee Technical Committee ISO/TC 61, Plastics, SC 6, Ageing,
chemical and environmental resistance, in collaboration with the European Committee for Standardization
Formatted: Font: Not Italic
(CEN) Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
Formatted: Font: Not Italic
between ISO and CEN (Vienna Agreement).
Formatted: Font: Not Italic
This second edition cancels and replaces the first edition (ISO 877-2:2009), which has been technically
revised.
The main changes are as follows:
— addition of a requirement for the area beneath and in the vicinity of racks in 5.1;5.1;
— clarification that no shadow of nearby objects shall fall on the specimens in 7.2;7.2;
— addition of Bibliography to include reference from 5.3,5.3, NOTE 2;
— deletion of NOTE in 5.4.5.4.
A list of all parts in the ISO 877 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
Formatted: English (United Kingdom)
complete listing of these bodies can be found at www.iso.org/members.htmlwww.iso.org/members.html.
...
PROJET FINAL
Norme
internationale
ISO/FDIS 877-2
ISO/TC 61/SC 6
Plastiques — Méthodes d'exposition
Secrétariat: DIN
au rayonnement solaire —
Début de vote:
2025-05-07
Partie 2:
Exposition directe et exposition
Vote clos le:
2025-07-02
derrière une vitre en verre
Plastics — Methods of exposure to solar radiation —
Part 2: Direct weathering and exposure behind window glass
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
Numéro de référence
ISO/FDIS 877-2:2025(fr) © ISO 2025
PROJET FINAL
ISO/FDIS 877-2:2025(fr)
Norme
internationale
ISO/FDIS 877-2
ISO/TC 61/SC 6
Plastiques — Méthodes d'exposition
Secrétariat: DIN
au rayonnement solaire —
Début de vote:
Partie 2: 2025-05-07
Exposition directe et exposition
Vote clos le:
2025-07-02
derrière une vitre en verre
Plastics — Methods of exposure to solar radiation —
Part 2: Direct weathering and exposure behind window glass
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
© ISO 2025 INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
NORMES POUVANT
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse Numéro de référence
ISO/FDIS 877-2:2025(fr) © ISO 2025
ii
ISO/FDIS 877-2:2025(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 1
5 Appareillage . 1
5.1 Exigences générales .1
5.2 Dispositif de fixation pour les essais d’exposition réalisés selon la méthode A .2
5.3 Dispositif de fixation pour les essais d’exposition réalisés selon la méthode B .2
5.4 Appareillage pour le mesurage des facteurs climatiques .3
6 Éprouvettes. 3
7 Conditions d’exposition des éprouvettes . 4
7.1 Aspect de l’exposition .4
7.2 Site d’exposition.4
8 Phases d’exposition . 4
8.1 Généralités .4
8.2 Durée de l’exposition.4
8.3 Exposition énergétique solaire .5
9 Mode opératoire . 5
9.1 Montage des éprouvettes .5
9.1.1 Généralités .5
9.1.2 Méthode A .5
9.1.3 Méthode B .5
9.2 Montage des matériaux de référence (s’ils sont utilisés) .5
9.3 Observations climatiques .5
9.4 Exposition des éprouvettes .5
9.4.1 Généralités .5
9.4.2 Méthode A .5
9.4.3 Méthode B .6
9.5 Détermination des modifications de propriétés .6
10 Expression des résultats . 6
10.1 Détermination des modifications de propriétés .6
10.2 Conditions climatiques .6
11 Rapport d’essai . 6
Bibliographie . 7
iii
ISO/FDIS 877-2:2025(fr)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux
de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général
confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de brevet revendiqué à cet égard. À la date de publication du présent document, l’ISO n’avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l’adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de
l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 6,
Vieillissement et résistance aux agents chimiques et environnants, en collaboration avec le comité technique
CEN/TC 249, Plastiques, du Comité européen de normalisation (CEN), conformément à l’Accord de
coopération technique entre l’ISO et le CEN (Accord de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 877-2:2009), qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes:
— ajout d’une exigence concernant la zone sous et à proximité des supports en 5.1;
— indication que l’ombre des objets à proximité ne doit pas tomber sur les éprouvettes en 7.2;
— ajout de la Bibliographie pour inclure une référence citée en 5.3, NOTE 2;
— suppression de la NOTE en 5.4.
Une liste de toutes les parties de la série ISO 877 est disponible sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/fr/members.html.
iv
PROJET FINAL Norme internationale ISO/FDIS 877-2:2025(fr)
Plastiques — Méthodes d'exposition au rayonnement
solaire —
Partie 2:
Exposition directe et exposition derrière une vitre en verre
1 Domaine d’application
Le présent document spécifie une méthode d’exposition directe des plastiques au rayonnement solaire
(méthode A) et une méthode d’exposition des plastiques au rayonnement solaire sous filtre de verre
(exposition derrière une vitre en verre) (méthode B). L’objectif consiste à évaluer les changements de
propriété produits après des phases d’exposition spécifiées.
[1]
Des lignes directrices générales relatives au domaine d’application de la série ISO 877 sont données dans
l’ISO 877-1.
2 Références normatives
Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu, des exigences du
présent document. Pour les références datées, seule l’édition citée s’applique. Pour les référen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.