ISO 13105-1:2014
(Main)Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 1: Terms and commercial specifications
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 1: Terms and commercial specifications
ISO 13105-1:2014 defines terms and commercial specifications for machines used for concrete surface floating and finishing (also known as power trowels). This includes pedestrian-controlled equipment and ride-on equipment. It does not address strike-off type machines, commonly known as screeds.
Machines et matériels pour la construction des bâtiments — Talocheuses-lisseuses de mortier — Partie 1: Terminologie et spécifications commerciales
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 13105-1
First edition
2014-12-01
Building construction machinery and
equipment — Machinery for concrete
surface floating and finishing —
Part 1:
Terms and commercial specifications
Machines et matériels pour la construction des bâtiments —
Talocheuses-lisseuses de mortier —
Partie 1: Terminologie et spécifications commerciales
Reference number
ISO 13105-1:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 13105-1:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 13105-1:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Terms and definitions . 1
3 Commercial specifications . 1
3.1 General . 1
3.2 Pedestrian-controlled power trowel . 2
3.3 Ride-on power trowel . 3
Annex A (informative) Power trowel dimensions in operating mode . 4
Bibliography . 6
© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 13105-1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
Fo
...
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13105-1
ISO/TC 195/SC 1 Secretariat: JISC
Voting begins on: Voting terminates on:
2014-01-14 2014-04-14
Building construction machinery and equipment —
Machinery for concrete surface floating and finishing —
Part 1:
Terms and commercial specifications
Machines et matériels pour la construction des bâtiments — Talocheuses-lisseuses de mortier —
Partie 1: Terminologie et spécifications commerciales
ICS: 01.040.91;91.220
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 13105-1:2013(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2013
---------------------- Page: 1 ----------------------
ISO/DIS 13105-1:2013(E)
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2013 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 13105-1
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Commercial specifications . 2
4.1 General . 2
4.2 Pedestrian controlled power trowel . 3
4.3 Ride-on power trowel . 3
Annex A (informative) Power Trowel Dimensions in Operating Mode . 4
Bibliography . 6
© ISO 2013 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/DIS 13105-1
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard r
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.