ISO 4113:2010
(Main)Road vehicles — Calibration fluids for diesel injection equipment
Road vehicles — Calibration fluids for diesel injection equipment
ISO 4113:2010 specifies the requirements for calibration fluids, i.e. a basic fluid and a closer value (CV) fluid, intended for testing and calibrating diesel fuel injection equipment in production, in service and in laboratories. The CV calibration fluid requires a closer tolerance range for kinematic viscosity and density, and can be specified to enhance the accuracy of the calibration setting. ISO 4113:2010 also allows the specification of an anti-wear (AW) requirement in order to aid the running-in of diesel fuel injection equipment.
Véhicules routiers — Fluides d'essai pour équipements d'injection à gazole
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 4113
Third edition
2010-06-01
Road vehicles — Calibration fluids for
diesel injection equipment
Véhicules routiers — Fluides d'essai pour équipements d'injection à
gazole
Reference number
ISO 4113:2010(E)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 4113:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 4113:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4113 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 7, Injection
equipment and filters for use on road vehicles.
This third edition cancels and replaces the second edition (ISO 4113:1988), which has been technically
revised.
© ISO 2010 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 4113:2010(E)
Road vehicles — Calibration fluids for diesel injection
equipment
1 Scope
This International Standard specifies the requirements for calibration fluids, i.e. a basic fluid and a closer value
(CV) fluid, intended for testing and calibrating diesel fuel injection equipment in production, in service, and in
laboratories. The CV calibration fluid requires a closer tolerance range for kinematic viscosity and density, and
can be specified to enhance the accuracy of the calibration setting.
This International Standard also allows the specification of an anti-wear (AW) requirement in order to aid the
running-in of diesel fuel injection equipment.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2049, Petroleum products — Determination of colour (ASTM scale)
ISO 2160, Petroleum products — Corrosiveness to copper — Copper strip test
ISO 2719, Determination of flash point — Pensky-Martens closed cup method
ISO 3015, Petroleum products — Determination of cloud point
ISO 3104, Petroleum products — Transparent and opaque liquids — Determination of kinematic viscosity and
calculation of dynamic viscosity
ISO 3405, Petroleum products — Determination of distillation characteristics at atmospheric pressure
ISO 3675, Crude petroleum and liquid petroleum products — Laboratory determination of density —
Hydrometer method
ISO 12937, Petroleum products — Determination of water — Coulometric Karl Fischer titration method
ASTM D665-06, Standard test method for rust-preventing characteristics of inhibited mineral oil in the
presence of water
ASTM D892-06, Standard test method for foaming characteristics of lubricating oils
ASTM D1748-02(2008), Standard test method for rust protection by metal preservatives in the humidity
cabinet
ASTM D2140-08, Standard practice for calculating carbon-type composition of insulating oils of petroleum
origin
© ISO 2010 – All rights reserved 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.