ISO 9838:2015

Alpine and touring ski-bindings — Test soles for ski-binding tests

ISO 9838:2015 defines test soles representing - an alpine ski-boot (form A) or at least the bottom part of it to be used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465, and - a touring ski-boot (form T) or at least the bottom part of it to be used for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465. NOTE Ski-boots have their own International Standards (ISO 5355 and ISO 9523) that allow relatively large tolerances in defining the test sole which are generally believed to be suitable for on-slope use by skiers, but too large for reproducible laboratory measurements.

Fixations de skis alpins et de randonnée — Semelles d'essai pour les essais de fixations de skis

L'ISO 9838:2015 définit des semelles d'essai représentant ? une chaussure de ski alpin (forme A) ou au moins la partie inférieure de celle-ci à utiliser pour les essais sur des fixations de skis alpins conformément à l'ISO 9462 et à l'ISO 9465, et ? une chaussure de ski de randonnée (forme T) ou au moins la partie inférieure de celle-ci à utiliser pour les essais sur des fixations de skis de randonnée conformément à l'ISO 13992 et à l'ISO 9465. NOTE Les chaussures de ski font l'objet de Normes internationales spécifiques (ISO 5355 et ISO 9523) qui admettent des tolérances relativement étendues pour la définition de la semelle d'essai. Ces tolérances sont généralement réputées appropriées pour une utilisation sur piste par les skieurs, mais elles sont considérées comme insuffisamment restrictives pour réaliser des mesurages en laboratoire reproductibles.

Varnostne vezi za alpske in turne smuči - Preskusni vložek za preskušanje varnostnih vezi

Ta mednarodni standard določa preskusne podplate, ki predstavljajo
– smučarski čevelj za alpsko smučanje (oblika A) ali vsaj njegov spodnji del, ki se uporablja za preskušanje smučarskih vezi za alpsko smučanje v skladu s standardoma ISO 9462 in ISO 9465, in
– turni smučarski čevelj (oblika T) ali vsaj njegov spodnji del, ki se uporablja za preskušanje smučarskih vezi za turno smučanje v skladu s standardoma ISO 13992 in ISO 9465.
OPOMBA Za smučarske čevlje veljajo drugi mednarodni standardi (ISO 5355 in ISO 9523), ki omogočajo sorazmerno velika odstopanja pri določanju preskusnih podplatov, za katere na splošno velja, da so primerni za smučanje na pobočjih, vendar preveliki za ponovljive laboratorijske meritve.

General Information

• Status: Withdrawn
• Publication Date: 07-Sep-2015
• Withdrawal Date: 07-Sep-2015
• ICS: 97.220.20 - Winter sports equipment
• Technical Committee: ISO/TC 83/SC 4 - Snowsports equipment
• Drafting Committee: ISO/TC 83/SC 4/WG 1 - Boots for ski and snowboard
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 13-Mar-2019
• Ref Project: SIST ISO 9838:2017 - Alpine and touring ski-bindings - Test soles for ski-binding tests

Relations

• Revised: ISO 9838:2019 - Alpine and touring ski-bindings — Test soles for ski-binding tests
• Effective Date: 11-Nov-2017
• Revises: ISO 9838:2008 - Alpine and touring ski-bindings — Test soles for ski-binding tests
• Effective Date: 01-Nov-2014

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 9838:2017
01-oktober-2017
1DGRPHãþD
SIST ISO 9838:2011
9DUQRVWQHYH]L]DDOSVNHLQWXUQHVPXþL3UHVNXVQLYORåHN]DSUHVNXãDQMH
YDUQRVWQLKYH]L
Alpine and touring ski-bindings - Test soles for ski-binding tests
Fixations de skis alpins et de randonnée -- Semelles d'essai pour les essais de fixations
de skis
Ta slovenski standard je istoveten z: ISO 9838:2015
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
SIST ISO 9838:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 9838:2017

---------------------- Page: 2 ----------------------

SIST ISO 9838:2017
INTERNATIONAL ISO
STANDARD 9838
Third edition
2015-09-01
Alpine and touring ski-bindings —
Test soles for ski-binding tests
Fixations de skis alpins et de randonnée — Semelles d’essai pour les
essais de fixations de skis
Reference number
ISO 9838:2015(E)
©
ISO 2015

---------------------- Page: 3 ----------------------

SIST ISO 9838:2017
ISO 9838:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 9838:2017
ISO 9838:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material and manufacture . 2
5 Dimensions . 2
6 Mechanical properties . 5
6.1 Flexional stiffness . 5
6.2 Compressional stiffness . 6
6.3 Hardness . 7
6.3.1 Form A types A and C . 7
6.3.2 Form T . 7
6.4 Coefficient of friction . 7
6.4.1 Form A types A and C . 7
6.4.2 Form T . 7
6.5 Coefficient of thermal expansion . 8
6.6 Requirements . 8
7 Long-term use . 8
Bibliography . 9
© ISO 2015 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 9838:2017
ISO 9838:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 83, Sports and other recreational facilities and
equipment, Subcommittee SC 4, Snowsports equipment.
This third edition cancels and replaces the second edition (ISO 9838:2008)
...

INTERNATIONAL ISO
STANDARD 9838
Third edition
2015-09-01
Alpine and touring ski-bindings —
Test soles for ski-binding tests
Fixations de skis alpins et de randonnée — Semelles d’essai pour les
essais de fixations de skis
Reference number
ISO 9838:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 9838:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 9838:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material and manufacture . 2
5 Dimensions . 2
6 Mechanical properties . 5
6.1 Flexional stiffness . 5
6.2 Compressional stiffness . 6
6.3 Hardness . 7
6.3.1 Form A types A and C . 7
6.3.2 Form T . 7
6.4 Coefficient of friction . 7
6.4.1 Form A types A and C . 7
6.4.2 Form T . 7
6.5 Coefficient of thermal expansion . 8
6.6 Requirements . 8
7 Long-term use . 8
Bibliography . 9
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 9838:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 83, Sports and other recreational facilities and
equipment, Subcommittee SC 4, Snowsports equipment.
This third edition cancels and replaces the second edition (ISO 9838:2008), of which it constitutes a
minor revision.
iv © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 9838:2015(E)
Alpine and touring ski-bindings — Test soles for ski-
binding tests
1 Scope
This International Standard defines test soles representing
— an alpine ski-boot (form A) or at least the bottom part of it
...

SLOVENSKI STANDARD
oSIST ISO 9838:2017
01-september-2017
9DUQRVWQHYH]L]DDOSVNHLQWXUQHVPXþL3UHVNXVQLYORåHN]DSUHVNXãDQMH
YDUQRVWQLKYH]L
Alpine and touring ski-bindings - Test soles for ski-binding tests
Fixations de skis alpins et de randonnée -- Semelles d'essai pour les essais de fixations
de skis
Ta slovenski standard je istoveten z: ISO 9838:2015
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
oSIST ISO 9838:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

oSIST ISO 9838:2017

---------------------- Page: 2 ----------------------

oSIST ISO 9838:2017
INTERNATIONAL ISO
STANDARD 9838
Third edition
2015-09-01
Alpine and touring ski-bindings —
Test soles for ski-binding tests
Fixations de skis alpins et de randonnée — Semelles d’essai pour les
essais de fixations de skis
Reference number
ISO 9838:2015(E)
©
ISO 2015

---------------------- Page: 3 ----------------------

oSIST ISO 9838:2017
ISO 9838:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------

oSIST ISO 9838:2017
ISO 9838:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material and manufacture . 2
5 Dimensions . 2
6 Mechanical properties . 5
6.1 Flexional stiffness . 5
6.2 Compressional stiffness . 6
6.3 Hardness . 7
6.3.1 Form A types A and C . 7
6.3.2 Form T . 7
6.4 Coefficient of friction . 7
6.4.1 Form A types A and C . 7
6.4.2 Form T . 7
6.5 Coefficient of thermal expansion . 8
6.6 Requirements . 8
7 Long-term use . 8
Bibliography . 9
© ISO 2015 – All rights reserved iii

---------------------- Page: 5 ----------------------

oSIST ISO 9838:2017
ISO 9838:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 83, Sports and other recreational facilities and
equipment, Subcommittee SC 4, Snowsports equipment.
This third edition cancels and replaces the second edition (ISO 9838:2008), of which it constitutes a
minor rev
...

NORME ISO
INTERNATIONALE 9838
Troisième édition
2015-09-01
Fixations de skis alpins et de
randonnée — Semelles d’essai pour
les essais de fixations de skis
Alpine and touring ski-bindings — Test soles for ski-binding tests
Numéro de référence
ISO 9838:2015(F)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 9838:2015(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 9838:2015(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Matériau et fabrication . 2
5 Dimensions . 2
6 Propriétés mécaniques . 5
6.1 Raideur en flexion . 5
6.2 Raideur en compression . 6
6.3 Dureté . 7
6.3.1 Forme A, types A et C . 7
6.3.2 Forme T . 7
6.4 Coefficient de frottement . 7
6.4.1 Forme A, types A et C . 7
6.4.2 Forme T . 7
6.5 Coefficient de dilatation thermique . 8
6.6 Exigences . 8
7 Durée d’utilisation . 8
Bibliographie . 9
© ISO 2015 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 9838:2015(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer
un engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à
l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes
de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos –
Informations supplémentaires.
Le comité chargé d’élaborer le présent document est l’ISO/TC 83, Matériel et équipements de sports et
autres activités de loisirs, sous-comité SC 4, Equipements de sport de neige.
Cette troisième édition annule et remplace la deuxième édition (ISO 9838:2008) dont elle constitue une
révision mineure.
iv © ISO 2015 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 9838:2015(F)
Fixations de skis alpins et de randonnée — Semelles
d’essai pour les essais de fixations de skis
1 Domaine d’application
La présente Norme internationale définit des semelles d’essai représentant
— une chaussure de ski alpin (forme A) ou au moins la partie inférieure de celle-ci à utiliser pour les
essais sur des fixations de skis alpins conformément à l’ISO 9462 et à l’ISO 9465, et
— une chaussure de ski de randonnée (forme T) ou au moins la partie inférieure de celle-ci à utiliser
pour les essais sur des fixations de skis de randonnée conformément à l’ISO 13992 et à l’ISO 9465.
NOTE Les chaussures de ski
...