ISO 8116-5:2008
(Main)Textile machinery and accessories — Beams for winding — Part 5: Sectional beams for warp knitting machines
Textile machinery and accessories — Beams for winding — Part 5: Sectional beams for warp knitting machines
ISO 8116-5:2008 specifies the main dimensions, mechanical strength, designation and permissible values of tolerances of form and position for the main elements of sectional beams for warp knitting machines.
Matériel pour l'industrie textile — Ensouples pour enroulement — Partie 5: Ensouples sectionnelles pour métiers à mailles jetées
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 8116-5
Third edition
2008-12-15
Textile machinery and accessories —
Beams for winding —
Part 5:
Sectional beams for warp knitting
machines
Matériel pour l'industrie textile — Ensouples pour enroulement —
Partie 5: Ensouples sectionnelles pour métiers à mailles jetées
Reference number
ISO 8116-5:2008(E)
©
ISO 2008
---------------------- Page: 1 ----------------------
ISO 8116-5:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 8116-5:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8116-5 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories,
Subcommittee SC 3, Machinery for fabric manufacturing including preparatory machinery and accessories.
This third edition cancels and replaces the second edition (ISO 8116-5:1995), which has been technically
revised.
ISO 8116 consists of the following parts, under the general title Textile machinery and accessories — Beams
for winding:
⎯ Part 1: General vocabulary
⎯ Part 2: Warper’s beams
⎯ Part 3: Weaver’s beams
⎯ Part 4: Test methods and quality classification of flanges for weaver’s beams, warper’s beams and
sectional beams
⎯ Part 5: Sectional beams for warp knitting machines
⎯ Part 6: Beams for ribbon weaving and ribbon knitting
⎯ Part 7: Beams for dyeing slivers, rovings and yarns
⎯ Part 8: Definitions of run-out tolerances and methods of measurement
⎯ Part 9: Dyeing beams for textile fabrics
© ISO 2008 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 8116-5:2008(E)
Textile machinery and accessories — Beams for winding —
Part 5:
Sectional beams for warp knitting machines
1 Scope
This part of ISO 8116 specifies the main dimensions, mechanical strength, designation and permissible values
of tolerances of form and position for the main elements of sectional beams for warp knitting machines. For
cases where a limit must be fixed for the residual imbalance, a recommendation is made for the choice of
quality grade.
2 Normative references
The following referenced documents
...
INTERNATIONAL ISO
STANDARD 8116-5
Third edition
2008-##-##
Textile machinery and accessories —
Beams for winding —
Part 5:
Sectional beams for warp knitting
machines
Matériel pour l'industrie textile — Ensouples pour enroulement —
Partie 5: Ensouples sectionnelles pour métiers à mailles jetées
PROOF/ÉPREUVE
Reference number
ISO 8116-5:2008(E)
©
ISO 2008
---------------------- Page: 1 ----------------------
ISO 8116-5:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2008 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 8116-5:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8116-5 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories,
Subcommittee SC 3, Machinery for fabric manufacturing including preparatory machinery and accessories.
This third edition cancels and replaces the second edition (ISO 8116-5:1995), which has been technically
revised.
ISO 8116 consists of the following parts, under the general title Textile machinery and accessories — Beams
for winding:
⎯ Part 1: General vocabulary
⎯ Part 2: Warper’s beams
⎯ Part 3: Weaver’s beams
⎯ Part 4: Test methods and quality classification of flanges for weaver’s beams, warper’s beams and
sectional beams
⎯ Part 5: Sectional beams for warp knitting machines
⎯ Part 6: Beams for ribbon weaving and ribbon knitting
⎯ Part 7: Beams for dyeing slivers, rovings and yarns
⎯ Part 8: Definitions of run-out tolerances and methods of measurement
⎯ Part 9: Dyeing beams for textile fabrics
© ISO 2008 – All rights reserved PROOF/ÉPREUVE iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 8116-5:2008(E)
Textile machinery and accessories — Beams for winding —
Part 5:
Sectional beams for warp knitting machines
1 Scope
This part of ISO 8116 specifies the main dimensions, mechanical strength, designation and permissible values
of tolerances of form and position for the main elements of sectional beams for warp knitting machines. For
cases where a limit must be fixed for the residual imbalance, a recommendation is made for the choice of
quality grade.
2 Normative references
The following referenced documents are ind
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.