ISO 9022-3:2015/Amd 1:2020

Optics and photonics - Environmental test methods - Part 3: Mechanical stress - Amendment 1

Optique et photonique — Méthodes d'essais d'environnement — Partie 3: Contraintes mécaniques — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 22-Sep-2020
• ICS: 37.020 - Optical equipment
• Technical Committee: ISO/TC 172/SC 1 - Fundamental standards
• Drafting Committee: ISO/TC 172/SC 1/WG 3 - Environmental test methods
• Current Stage: 9599 - Withdrawal of International Standard
• Start Date: 26-Apr-2022
• Completion Date: 13-Dec-2025

Relations

• Amends: ISO 9022-3:2015 - Optics and photonics - Environmental test methods - Part 3: Mechanical stress
• Effective Date: 06-Jun-2022
• Revised: ISO 9022-3:2022 - Optics and photonics - Environmental test methods - Part 3: Mechanical stress
• Effective Date: 16-Jul-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 9022-3
Third edition
2015-03-01
AMENDMENT 1
2020-09
Optics and photonics —
Environmental test methods —
Part 3:
Mechanical stress
AMENDMENT 1
Optique et photonique — Méthodes d'essais d'environnement —
Partie 3: Contraintes mécaniques
AMENDEMENT 1
Reference number
ISO 9022-3:2015/Amd.1:2020(E)
©
ISO 2020
ISO 9022-3:2015/Amd.1:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 9022-3:2015/Amd.1:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/o
...

INTERNATIONAL ISO
STANDARD 9022-3
Third edition
2015-03-01
AMENDMENT 1
2020-09
Optics and photonics —
Environmental test methods —
Part 3:
Mechanical stress
AMENDMENT 1
Optique et photonique — Méthodes d'essais d'environnement —
Partie 3: Contraintes mécaniques
AMENDEMENT 1
Reference number
ISO 9022-3:2015/Amd.1:2020(E)
©
ISO 2020
ISO 9022-3:2015/Amd.1:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 9022-3:2015/Amd.1:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/o
...