ISO 17288-1:2011
(Main)Passenger cars — Free-steer behaviour — Part 1: Steering-release open-loop test method
Passenger cars — Free-steer behaviour — Part 1: Steering-release open-loop test method
ISO 17288-1:2011 specifies an open-loop test method for determining the free control stability of a passenger car as defined in ISO 3833, by measurement of the transient behaviour following steering release, starting from a steady-state cornering status.
Voitures particulières — Comportement volant libre — Partie 1: Méthode d'essai en boucle ouverte avec relâchement du volant
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17288-1
Second edition
2011-02-15
Passenger cars — Free-steer
behaviour —
Part 1:
Steering-release open-loop test method
Voitures particulières — Comportement volant libre —
Partie 1: Méthode d'essai en boucle ouverte avec relâchement du
volant
Reference number
ISO 17288-1:2011(E)
©
ISO 2011
---------------------- Page: 1 ----------------------
ISO 17288-1:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 17288-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 17288 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17288-1 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 9, Vehicle
dynamics and road-holding ability.
This second edition cancels and replaces the first edition (ISO 17288-1:2002), of which it constitutes a minor
revision.
ISO 17288 consists of the following parts, under the general title Passenger cars — Free-steer behaviour :
⎯ Part 1: Steering-release open-loop test method
⎯ Part 2: Steering-pulse open-loop test method
© ISO 2011 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 17288-1:2011(E)
Introduction
The main purpose of this part of ISO 17288 is to provide repeatable and discriminatory test results.
The dynamic behaviour of a road vehicle is a very important aspect of active vehicle safety. Any given vehicle,
together with its driver and the prevailing environment, constitutes a closed-loop system that is unique. The
task of evaluating the dynamic behaviour is therefore very difficult since the significant interactions of these
driver-vehicle-environment elements are each complex in themselves. A complete and accurate description of
the behaviour of the road vehicle must necessarily involve information obtained from a number of different
tests.
Since this test method quantifies only one small part of the complete vehicle handling characteristics, the
results of these tests can only be considered significant for a correspondingly small part of the overall dynamic
behaviour.
Moreover, insufficient knowledge is available concerning the relationship between overall vehicle dynamic
properties and accident avoidance. A substantial amount of work is necessary to acquire sufficient and
reliable data on the correlation between accident avoidance and vehicle dynamic properties in general and the
results of these tests in particular. Consequently, any application of this test method for regulation purposes
will require proven correlation between test results and accident statistics.
iv © ISO 2011 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 17288-1:2011(E)
Passenger cars — Free-steer behaviour —
Part 1:
Steering-release open-loop test method
1 Scope
This part of ISO 17288 specifies an open-loop test method for determining the free control stability of a
passenger car as defined in ISO 3833, by measurement of the transient behaviour following steering release,
starting from a steady-state cornering status.
NOTE The open-loop manoeuvre specified in this part of ISO 17288 is not representative of normal driving
conditions, but is nonetheless useful for obtaining a measure of vehicle transient behaviour.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3833, Road vehicles — Types — Terms and definitions
ISO 8855, Road vehicles — Vehicle dynamics and road-holding ability — Vocabulary
ISO 15037-1:2006, Road vehicles — Vehicle dynamics test methods — Part 1: General conditions for
passenger cars
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3833 and ISO 8855 apply.
4 Principle
This test is intended for evaluating the ability of a vehicle to return to a straight path following steering-wheel
release from a steady-state turn.
The initial conditions are defined by a steady-state circular motion. During the test, the driver releases the
steering wheel. The steering-wheel angle and the vehicle response are measured and recorded. From the
recorded signals, characteristic values are calculated.
© ISO 2011 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 17288-1:2011(E)
5 Variables
5.1 Reference system
The provisions given in ISO 15037-1:2006, 3.1, apply.
5.2 Measurement
Measure the following variables (see ISO 8855):
⎯ longitudinal velocity (v );
X
⎯ lateral acceleration (a );
Y
⎯ yaw velocity (ψ );
⎯ steering-wheel angle (δ ).
H
6 Measuring e
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.