Leather — Chemical tests — Preparation of chemical test samples

ISO 4044:2017 specifies how to prepare a test sample of leather for chemical analysis. The test sample can be either ground or cut into small pieces. Unless specified in this document, the method to be used depends on the size of leather sample available for testing.

Cuir — Essais chimiques - Préparation des échantillons pour essais chimiques

ISO 4044:2017 spécifie une méthode de préparation des échantillons pour essais destinés à l'analyse chimique d'un cuir. L'échantillon peut être broyé ou découpé en petits morceaux. Si elle n'est pas spécifiée dans le présent document, la méthode à utiliser dépend de la taille de l'échantillon de cuir dont on dispose pour l'essai.

General Information

Status
Published
Publication Date
02-Jan-2017
Current Stage
9093 - International Standard confirmed
Completion Date
14-Jun-2022
Ref Project

Relations

Buy Standard

Standard
ISO 4044:2017 - Leather -- Chemical tests -- Preparation of chemical test samples
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4044:2017 - Leather -- Chemical tests -- Preparation of chemical test samples
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4044:2017 - Cuir -- Essais chimiques - Préparation des échantillons pour essais chimiques
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4044:2017 - Cuir -- Essais chimiques - Préparation des échantillons pour essais chimiques
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 4044
IULTCS/IUC 3
Third edition
    2017-01
Leather — Chemical tests —
Preparation of chemical test samples
Cuir — Essais chimiques - Préparation des échantillons pour essais
chimiques
Reference numbers
ISO 4044:2017(E)
IULTCS/IUC 3:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 4044:2017(E)
IULTCS/IUC 3:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4044:2017(E)
IULTCS/IUC 3:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Preparation of test sample . 2
6.1 Sample preparation . 2
6.2 Grinding . 2
6.3 Cutting . 2
6.4 Choice of sample preparation method . 2
7 Storage of test sample . 2
Annex A (informative) Commercial sources for apparatus . 3
Bibliography . 4
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 4044:2017(E)
IULTCS/IUC 3:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html
ISO 4044 was prepared by the Chemical Test Commission of the International Union of Leather
Technologists and Chemists Societies (IUC Commission, IULTCS) in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, the secretariat of
which is held by UNI, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
It is based on IUC 3 originally published in J. Soc. Leather Trades Chemists, 49, pp. 8-10, 1965, and
declared an official method of the IULTCS in 1965.
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to
further the advancement of leather science and technology. IULTCS has three Commissions, which
are responsible for establishing international methods for the sampling and testing of leather. ISO
recognizes IULTCS as an international standardizing body for the preparation of test methods for
leather.
This third edition cancels and replaces the second edition (ISO 4044:2008), which has been technically
revised.
Experience has shown it can be difficult to find a suitable grinding (or cutter) mills for preparing ground
leather samples without considerable heating of the milling chamber or blocking of the sieve. Those
mills commercially available require reasonably large leather samples to prepare a representative
ground sample. But in many cas
...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 4044
IULTCS/IUC 3
IULTCS Secretariat:
Voting begins on: Voting terminates on:
2015-02-19 2015-05-19
Leather — Chemical tests — Preparation of chemical test
samples
Cuir — Essais chimiques - Préparation des échantillons pour essais chimiques
ICS: 59.140.30
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
�s�de��ned��n���e���enn�����ee�en��
This draft is hereby submitted to the ISO member bodies and to the CEN member
�od�es��o����������e�����e��on���en������
��o��d����s�d������e��cce��ed������n���d������es�����s�ed�on���e���s�s�o��co��en�s�
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
�o������o�e��n�����
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
co�����ee� sec�e�������� ���� �en����� �ec�e������� �o��� o�� ed���n�� �nd� �e���
BEING ACCEPTABLE FOR INDUSTRIAL,
co��os���on�������e��nde����en���������c���on�s���e�
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference numbers
NATIONAL REGULATIONS.
ISO/DIS 4044:2014(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
IULTCS/IUC 3:2014(E)
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2014

---------------------- Page: 1 ----------------------
ISO/DIS 4044:2014(E)
IULTCS/IUC 3:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 4044
Contents Page
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Preparation of test sample . 2
6.1 Sample preparation . 2
6.2 Grinding . 2
6.3 Cutting . 2
6.4 Choice of sample preparation method . 2
7 Storage of test sample . 2
Annex A (informative) Commercial sources for apparatus . 3
A.1 Grinding apparatus . 3


© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 4044
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to further the
advancement of leather science and technology. IULTCS has three Commissions, which are responsible for
establishing international methods for the sampling and testing of leather. ISO recognizes IULTCS as
an international standardizing body for the preparation of test methods for leather.
ISO 4044/IUC 3 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 289, Leather, in collaboration with the Chemical Tests Commission of the International Union of
Leather Technologists and Chemists Societies (IUC Commission, IULTCS), in accordance with the
Agreement on technical co-operation between ISO and CEN (Vienna Agreement). It is based on IUC 3
originally published in J. Soc. Leather Trades Chemists, 49, pp. 8-10, 1965, and declared an official method of
the IULTCS in 1965.
The second edition was a technical revision of the first edition (ISO 4044:1977).
This third edition (ISO 4044:
...

NORME ISO
INTERNATIONALE 4044
IULTCS/IUC 3
Troisième édition
2017-01
Cuir — Essais chimiques - Préparation
des échantillons pour essais
chimiques
Leather — Chemical tests — Preparation of chemical test samples
Numéros de référence
ISO 4044:2017(F)
IULTCS/IUC 3:2017(F)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 4044:2017(F)
IULTCS/IUC 3:2017(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 4044:2017(F)
IULTCS/IUC 3:2017(F)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe . 1
5 Appareillage . 1
6 Préparation de l’échantillon pour essai . 2
6.1 Préparation de l’échantillon . 2
6.2 Broyage . 2
6.3 Découpe. 2
6.4 Choix de la méthode de préparation des échantillons . 2
7 Conservation de l’échantillon pour essai . 2
Annexe A (informative) Sources d’approvisionnement en appareillage . 3
Bibliographie . 4
© ISO 2017 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 4044:2017(F)
IULTCS/IUC 3:2017(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation
de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’Organisation
mondiale du commerce (OMC) concernant les obstacles techniques au commerce (OTC), voir le lien
suivant: www.iso.org/iso/fr/avant-propos.html
L’ISO 4044 a été élaborée par la Commission des essais chimiques de l’Union internationale des sociétés
de techniciens et chimistes du cuir (commission IUC, IULTCS) en collaboration avec le comité technique
du Comité européen de normalisation (CEN) CEN/TC 289, Cuir, dont le secrétariat est tenu par l’UNI,
conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord de Vienne).
Elle est basée sur l’IUC 3, initialement publiée dans le J. Soc. Leather Trades Chemists, 49, pp. 8-10, 1965,
et déclarée méthode officielle de l’IULTCS en 1965.
L’IULTCS est une organisation mondiale de sociétés professionnelles des industries du cuir fondée en
1897 ayant pour mission de favoriser l’avancement des sciences et technologies du cuir. L’IULTCS a trois
commissions, qui sont responsables de l’établissement de méthodes internationales d’échantillonnage
et d’essai des cuirs. L’ISO reconnaît l’IULTCS en tant qu’organisme international à activités normatives
pour l’élaboration de méthodes d’essai relatives au cuir.
Cette troisième édition annule et remplace la seconde édition (ISO 4044:2008), qui a fait l’objet d’une
révision technique.
L’expérience montre qu’il peut être difficile de trouver un broyeur (ou moulin à couteaux) adéquat pour
préparer des échantillons de cuir broyé sans surchauffer le compartiment de broyage ou colmater le
tamis. Avec les broyeurs en vente dans le commerce, il faut des échantillons de cuir de taille suffisante
pour préparer un échantillon broyé représentatif. Cependant, dans un certain nombre de cas où les
essais portent sur des biens de consommation, on ne dispose que de pièces de cuir de petite taille.
Pour cette raison, le paragraphe 6.3 a été ajouté; il concerne la préparation des échantillons pour essai,
effectuée en découpant le cuir en petits morceaux à l’aide d’une lame effilée
...

PROJET DE NORME INTERNATIONALE ISO/DIS 4044
IULTCS/IUC 3
Secrétariat: IULTCS
Début de vote Vote clos le

2015-02-19 2015-05-19
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION    МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ    ORGANISATION INTERNATIONALE DE NORMALISATION

Cuir — Essais chimiques — Préparation des échantillons
pour essais chimiques
Leather — Chemical tests — Preparation of chemical test samples

ICS 59.140.30


TRAITEMENT PARALLÈLE ISO/CEN
Le présent projet a été élaboré dans le cadre du Comité européen de normalisation (CEN) et soumis
selon le mode de collaboration sous la direction du CEN, tel que défini dans l'Accord de Vienne.
Le projet est par conséquent soumis en parallèle aux comités membres de l'ISO et aux comités
membres du CEN pour enquête de cinq mois.
En cas d'acceptation de ce projet, un projet final, établi sur la base des observations reçues, sera
soumis en parallèle à un vote d'approbation de deux mois au sein de l'ISO et à un vote formel au sein
du CEN.

Ce projet de Norme internationale est soumis à tous les comités membres de l'ISO pour vote
en tant que norme élaborée par un organisme international à activités normatives
conformément à la Résolution du Conseil 42/1999. L’Union internationale des sociétés de
techniciens et chimistes du cuir (Commission IUC 3, IULTCS), qui en est l'auteur, a été
reconnu par le Conseil de l'ISO en tant qu'organisme international à activités normatives
selon les dispositions de la Résolution du Conseil 42/1999.

Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.

CE DOCUMENT EST UN PROJET DIFFUSÉ POUR OBSERVATIONS ET APPROBATION. IL EST DONC SUSCEPTIBLE DE MODIFICATION ET NE PEUT
ETRE CITE COMME NORME INTERNATIONALE AVANT SA PUBLICATION EN TANT QUE TELLE.
OUTRE LE FAIT D'ETRE EXAMINES POUR ETABLIR S'ILS SONT ACCEPTABLES A DES FINS INDUSTRIELLES, TECHNOLOGIQUES ET COMMERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES PROJETS DE NORMES INTERNATIONALES DOIVENT PARFOIS ETRE CONSIDERES DU POINT
DE VUE DE LEUR POSSIBILITE DE DEVENIR DES NORMES POUVANT SERVIR DE REFERENCE DANS LA REGLEMENTATION NATIONALE.
LES DESTINATAIRES DU PRÉSENT PROJET SONT INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS, NOTIFICATION DES DROITS DE PROPRIÉTÉ
DONT ILS AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À FOURNIR UNE DOCUMENTATION EXPLICATIVE.
©  Organisation Internationale de Normalisation, 2015

---------------------- Page: 1 ----------------------
ISO/DIS 4044
IULTCS/IUC 3


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2015
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur l’internet ou sur un Intranet, sans
autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à l’adresse ci-après ou au comité membre de l’ISO
dans le pays du demandeur.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2015 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO/DIS 4044
Sommaire Page
Avant-propos . iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 1
5 Appareillage . 1
6 Préparation de l'échantillon pour essai . 2
6.1 Préparation de l’échantillon . 2
6.2 Broyage . 2
6.3 Découpe. 2
6.4 Choix de la méthode de préparation des échantillons . 2
7 Conservation de l'échantillon pour essai . 2
Annexe A (informative) Sources d’approvisionnement appropriées pour l'appareillage . 3
A.1 Broyeur . 3

© ISO 2015 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO/DIS 4044
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'IULTCS est une organisation mondiale de sociétés professionnelles des industries du cuir fondée en 1897
ayant pour mission de favoriser l'avancement des sciences et technologies du cuir. L’IULTCS a trois
commissions, qui sont responsables de l’établissement de méthodes internationales d’échantillonnage et
d’essai des cuirs. L’ISO reconnaît l’IULTCS en tant qu’organisme international à activités normatives pour
l’élaboration de méthodes d’essai relatives au cuir.
L'ISO 4044/IUC 3 a été élaborée par le comité technique CEN/TC 289, Cuir, du Comité européen de
normalisation (CEN), en collaboration avec la Commission des essais chimiques de l'Union internationale des
sociétés de techniciens et chimistes du cuir (commission IUC, IULTCS), conformément à l'Accord de
coopération technique entre l'ISO et le CEN (Accord de Vienne). Elle est basée sur l’IUC 3, initialement
publiée dans le J. Soc. Leather Trades Chemists, 49, pp. 8-10, 1965, et déclarée méthode officielle de
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.