iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 5600:2024

(Main)

Rubber — Determination of adhesion to rigid materials using conical shaped parts

Rubber — Determination of adhesion to rigid materials using conical shaped parts

This document specifies a method for the determination of the static vulcanized adhesion strength of rubber compounds to rigid materials. The test piece is composed of two conical ends of the rigid material, joined by a cylinder of rubber. The adhesion is obtained by a bonding system which can include not only the rigid material and the rubber compound, but other elements such as thin alloy coatings or chemical treatments of rigid parts and either a single cement or both primer and cover cements. The bonding system for preparing the test pieces should be adequately specified by the user, but a provision is made in this document for the evaluation of different types of failure related to a complex bonding system. The method is designed primarily for test pieces prepared in the laboratory under standard conditions in order to provide data for development and control of bonding systems and their components, such as cements or special rubber compounds, and of methods of manufacture. While intended to be applied where the rubber is bonded to rigid supporting pieces, it can be inapplicable such cases where the support, although of high-modulus material, has a low rigidity due to small transverse dimensions, as in the case of rubber bonded to metal wires, cords or thin sheets.

Caoutchouc — Détermination de l'adhérence aux matériaux rigides au moyen de pièces coniques

General Information

Status
Published
Publication Date
21-Apr-2024
ICS
83.060 - Rubber
Technical Committee
ISO/TC 45/SC 2 - Testing and analysis
Drafting Committee
ISO/TC 45/SC 2 - Testing and analysis
Current Stage
6060 - International Standard published
Start Date
22-Apr-2024
Due Date
04-May-2025
Completion Date
22-Apr-2024
Ref Project

Relations

Revises
ISO 5600:2017 - Rubber — Determination of adhesion to rigid materials using conical shaped parts
Effective Date
06-May-2023

Buy Standard

ISO 5600:2024 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:22. 04. 2024ISO 5600:2024 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:22. 04. 2024
PreviousNext
Standard
ISO 5600:2024 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:22. 04. 2024
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
ISO/PRF 5600 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:4. 03. 2024ISO/PRF 5600 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:4. 03. 2024
PreviousNext
Draft
ISO/PRF 5600 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:4. 03. 2024
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ISO/PRF 5600 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:4. 03. 2024REDLINE ISO/PRF 5600 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:4. 03. 2024
PreviousNext
Draft
REDLINE ISO/PRF 5600 - Rubber — Determination of adhesion to rigid materials using conical shaped parts Released:4. 03. 2024
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

International
Standard
ISO 5600
Sixth edition
Rubber — Determination of
2024-04
adhesion to rigid materials using
conical shaped parts
Caoutchouc — Détermination de l'adhérence aux matériaux
rigides au moyen de pièces coniques
Reference number
ISO 5600:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 5600:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland

© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 5600:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Calibration . 2
7 Test piece . 2
7.1 Form and dimensions .2
7.2 Materials .2
7.3 Preparation .3
7.4 Number of test pieces .3
7.5 Conditioning of test pieces .4
8 Procedure . 4
9 Expression of results . 4
9.1 Adhesion value.4
9.2 Type of adhesion failure .4
10 Salv
...

International
Standard
ISO 5600
Sixth edition
Rubber — Determination of
adhesion to rigid materials using
conical shaped parts
Caoutchouc — Détermination de l'adhérence aux matériaux
rigides au moyen de pièces coniques
PROOF/ÉPREUVE
Reference number
ISO 5600:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
ISO 5600:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO 5600:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Calibration . 2
7 Test piece . 2
7.1 Form and dimensions .2
7.2 Materials .2
7.3 Preparation .3
7.4 Number of test pieces .3
7.5 Conditioning of test pieces .4
8 Procedure . 4
9 Expression of results . 4
9.1 Adhesion value.4
9.2 Type of adhesion failure .
...

ISO/DIS PRF 5600:2023(E)
Date: 2023-XX-XX
ISO/TC 45/SC 2/WG 1
Secretariat: JISC
Date: 2024-03-01
Rubber — Determination of adhesion to rigid materials using conical
shaped parts
Caoutchouc — Détermination de l'adhérence aux matériaux rigides au moyen de pièces coniques
PROOF

---------------------- Page: 1 ----------------------
ISO/PRF 5600:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved

ii

---------------------- Page: 2 ----------------------
ISO/PRF 5600:2024(en)
Contents
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Calibration . 2
7 Test piece . 2
7.1 Form and dimensions . 2
7.2 Materials . 2
7.3 Preparation . 3
7.4 Number of test pieces . 4
7.5 Conditioning of test pieces . 4
8 Procedure . 4
9 Expression of results . 4
9.1 Adhesion value . 4
9.2 Type of adhesion failure . 4
10 Salvaging of bonded metal parts . 5
11 Test report . 5
Annex A (normative) Calibration schedule .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 1817(Main)
Rubber, vulcanized or thermoplastic — Determination of the effect of liquids

This document describes methods of evaluating the resistance of vulcanized and thermoplastic rubbers to the action of liquids by measurement of properties of the rubbers before and after immersion in test liquids. The liquids concerned include current service liquids, such as petroleum derivatives, organic solvents and chemical reagents, as well as reference test liquids.

  • Standard
    31 pages
    English language
    sale 15% off
  • Standard
    32 pages
    French language
    sale 15% off
ISO
ISO 3384-1:2024(Main)
Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression — Part 1: Testing at constant temperature

This document specifies two procedures for determining the decrease in counterforce exerted by a test piece of vulcanized or thermoplastic rubber which has been compressed to a constant deformation and maintained thus at a predetermined test temperature. The counterforce can be determined either by means of a continuous-measurement system or by a discontinuous-measurement one. Two test methods are specified, method A and method B. In method A the compression and all measurements of counterforce are made at test temperature and in method B the compression and all measurements of counterforce are made at standard laboratory temperature. Method A and method B do not give the same results, as in method B the shrinkage of the material from the test temperature to standard laboratory temperature is included in the result. Two forms of test piece are specified in this document: cylindrical test pieces and rings. Comparison of results is valid only when made on test pieces of similar size and shape. The use of ring test pieces is particularly suitable for the determination of stress relaxation in liquid environments. This document deals only with testing at constant ambient or elevated temperature. Testing at temperatures below standard laboratory temperature is not specified. The methods have been used for low‑temperature testing, but their reliability under these conditions is not proven.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    15 pages
    French language
    sale 15% off
ISO
ISO 9924-3:2024(Main)
Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 3: Hydrocarbon rubbers, halogenated rubbers and polysiloxane rubbers

This document specifies a thermogravimetric method for the determination of the main constituents of rubber compounds such as elastomer(s), carbon black and mineral filler. It establishes the “fingerprint” of the tested material. However, the result does not always correspond exactly to the theoretical formula of the rubber. This method applies to raw or compounded rubbers, vulcanized and unvulcanised, with or without extraction. This method applies to rubbers with hydrocarbon backbones (NR, BR, SBR, IIR, EPDM, ACM, AEM, etc.) used alone or as mixtures. For the mixtures, the polymer content corresponds to the total rubber and it is not usually possible to identify individual polymers. This method applies to rubbers with halogenated hydrocarbon backbones (CR, CSM, FKM, CM, CO, ECO, etc.) or containing nitrogen (NBR, HNBR, NBR/PVC, etc.), as well as to their mixtures. However, these rubbers often form carbonaceous residues which interfere with the analysis. Application of an appropriate procedure minimizes these interferences. This method also applies to rubbers with a polysiloxane backbone (VMQ, etc.) and to rubbers not listed above.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    French language
    sale 15% off
ISO
ISO 813-2:2024(Main)
Rubber, vulcanized or thermoplastic — Determination of adhesion to a rigid substrate — Part 2: Adhesion of a soft thermoplastic elastomer layer

This document specifies a test method for assessing the peel strength of a thermoplastic elastomer (TPE) to a rigid substrate. It is mainly applicable to soft components in the Shore A hardness range. This document specifies a test piece but not the injection moulding tool for its manufacture. Hence, it is possible that different results are obtained for test pieces produced using different injection moulding tools.

  • Standard
    15 pages
    English language
    sale 15% off
ISO
ISO 23337:2024(Main)
Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using the Improved Lambourn test machine

This document specifies a method for the determination of the resistance of rubber to abrasion using the Improved Lambourn test machine. The abrasion loss resulting from the slip caused by the difference in circumferential speed between a disc-shaped rubber test piece and an abrasive wheel, which are driven to rotate independently with their circumferences pressed against each other by a specified load, is determined. The test result can be reported as a volume loss per abrasion test time or running distance, and/or as an abrasion resistance index compared with a reference compound. As the Improved Lambourn test machine is capable of setting various abrasive conditions, such as slip rate, sliding speed and load, independently, this method is suitable for the evaluation of compounds for a range of rubber products, especially tyres, under a wide range of severity conditions. An example of the testing of tyre tread rubber is given in Annex A.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    French language
    sale 15% off
ISO
ISO 13145:2023(Main)
Rubber — Determination of viscosity and stress relaxation using a rotorless sealed shear rheometer

This document describes a method for the determination of the viscosity and stress relaxation of raw or compounded rubber under specified conditions. The viscosity determination consists of a constant strain, temperature and frequency test in which the elastic and the loss components of the complex shear modulus can be determined. The determination of stress relaxation consists of a constant static strain and temperature test in which the torque decrease can be determined.

  • Standard
    15 pages
    English language
    sale 15% off
ISO
ISO 11346:2023(Main)
Rubber, vulcanized or thermoplastic — Estimation of life-time and maximum temperature of use

This document specifies the principles and procedures for estimating the thermal endurance of rubbers from the results of exposure to elevated temperatures for long periods. Two approaches are specified (see Introduction): — one using the Arrhenius equation; — the other using the WLF equation. In this document, the estimation of thermal endurance is based solely on the change in selected properties resulting from periods of exposure to elevated temperatures. The various properties of rubbers change at different rates on thermal ageing, hence comparison between different rubbers can only be made using the same properties.

  • Standard
    21 pages
    English language
    sale 15% off
  • Draft
    21 pages
    French language
    sale 15% off
ISO
ISO 24087:2023(Main)
Rubber, vulcanized — Determination of the glass transition temperature and enthalpy by differential scanning calorimetry

This document specifies a method of thermal analysis of vulcanized rubber by differential scanning calorimetry (DSC). This method is intended for the observation and measurement of various properties and phenomena associated, such as physical transitions (glass transition, melting and crystallization, polymorphic transitions, etc.).

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    French language
    sale 15% off
ISO
ISO 1407:2023(Main)
Rubber — Determination of solvent extract

This document specifies four methods for the quantitative determination of the material extractable from raw rubbers, both natural and synthetic; two of the methods are also applicable to the unvulcanized and vulcanized rubber compounds. Method A measures the mass of the solvent extract, after evaporation of the solvent, relative to the mass of the original test portion. Method B measures the difference in the mass of the test portion before and after extraction. Method C, which is for raw rubbers only, measures the difference in the mass of the test portion before and after extraction using boiling solvent. Method D, which is for raw rubbers only, measures the difference in the mass of the test portion before and after extraction relative to the mass of the original test portion. NOTE 1 Depending on the test method used, the conditioning of the test portion and the solvent used, the test result is not necessarily the same. NOTE 2 Method C generally gives results which are lower than those obtained with methods A and B due to an equilibrium which is set up, particularly if large test portions are used, depending on the content and the nature of the extractable matter. Method C is, however, a quicker method than method A or method B. NOTE 3 Methods C and D are not suitable if the test portion disintegrates during the extraction. NOTE 4 Method D is normally used for production controls. Recommendations as to the solvent most appropriate for each type of rubber are given in Annex A.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off
ISO
ISO 9924-1:2023(Main)
Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 1: Butadiene, ethylene-propylene copolymer and terpolymer, isobutene-isoprene, isoprene and styrene-butadiene rubbers

ISO 9924-1:2016 specifies a thermogravimetric method for the determination of the total organic content, carbon black content and ash in vulcanizates and uncured compounds. The loss in mass at 300 °C is an approximate guide to the volatile-matter content of the compound. The method is suitable for the analysis of rubber compounds and vulcanizates containing the following rubbers occurring alone or as mixtures: a) polyisoprene of natural or synthetic origin; b) polybutadiene; c) styrene-butadiene copolymers; d) isobutylene-isoprene copolymers; e) ethylene-propylene copolymers and related terpolymers. NOTE The field of application of the method may be extended to the analysis of compounds containing rubbers different from those given in this subclause, provided that the applicability of the method is tested beforehand using known compounds or vulcanizates having a similar composition. Other compounds are covered in ISO 9924‑2. The method is not suitable for rubbers containing polymers which form a carbonaceous residue during pyrolysis, such as many chlorine- or nitrogen-containing rubbers. The method is also not suitable for materials containing additives which cause the formation of carbonaceous residues during pyrolysis, such as cobalt and lead salts or phenolic resins. The method is not suitable for compounds containing mineral fillers, such as carbonates or hydrated aluminium oxides, which decompose in the temperature range from 25 °C to 650 °C, unless suitable corrections based on prior knowledge of filler behaviour can be made. The method is not suitable for the determination of the total polymer content of compounds or vulcanizates containing non-rubber organic ingredients that cannot be completely removed by solvent extraction carried out in accordance with ISO 1407.

  • Standard
    10 pages
    English language
    sale 15% off