ISO 4586-2:2015
(Main)High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 2: Determination of properties
High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 2: Determination of properties
ISO 4586-2:2015 specifies the methods of test for determination of the properties of High-Pressure Decorative Laminates (HPL, HPDL). These methods are primarily intended for testing the sheets specified from ISO 4586‑3 to ISO 4586‑8.
Stratifiés décoratifs haute pression (HPL, HPDL) — Plaques à base de résines thermodurcissables (communément appelées stratifiés) — Partie 2: Détermination des caractéristiques
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 4586-2
Sixth edition
2015-11-01
High-pressure decorative laminates
(HPL, HPDL) — Sheets based on
thermosetting resins (Usually called
Laminates) —
Part 2:
Determination of properties
Stratifiés décoratifs haute pression (HPL, HPDL) — Plaques à base de
résines thermodurcissables (communément appelées stratifiés) —
Partie 2: Détermination des caractéristiques
Reference number
ISO 4586-2:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 4586-2:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 4586-2:2015(E)
Contents Page
Foreword .ix
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Assessment of appearance . 2
4.1 Principle . 2
4.2 Apparatus . 2
4.3 Test specimen . 2
4.4 Procedure . 2
4.5 Test report . 3
5 Determination of thickness . 3
5.1 Principle . 3
5.2 Apparatus . 3
5.3 Test specimen . 3
5.4 Procedure . 3
5.5 Test report . 3
6 Determination of length and width . 4
6.1 Principle . 4
6.2 Apparatus . 4
6.3 Test specimen . 4
6.4 Procedure . 4
6.5 Expression of results . 4
6.6 Test report . 4
7 Determination of edge straightness . 4
7.1 Principle . 4
7.2 Apparatus . 4
7.3 Test specimen . 4
7.4 Procedure . 5
7.5 Expression of results . 5
7.6 Test report . 5
8 Determination of edge squareness (Method A) . 6
8.1 Principle . 6
8.2 Apparatus . 6
8.3 Test specimen . 6
8.4 Procedure . 6
8.5 Expression of results . 6
8.6 Test report . 7
9 Determination of edge squareness (Method B) . 7
9.1 Principle . 7
9.2 Apparatus . 7
9.3 Test specimen . 7
9.4 Procedure . 7
9.5 Expression of results . 8
9.6 Test report . 8
10 Determination of flatness . 8
10.1 Principle . 8
10.2 Apparatus . 8
10.3 Test specimens . 8
10.4 Procedure . 8
10.5 Expression of results . 8
10.6 Test report . 8
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 4586-2:2015(E)
11 Resistance to surface wear . 9
11.1 Principle . 9
11.2 Materials . 9
11.3 Apparatus .10
11.4 Test specimens .10
11.5 Preparation of specimens and abrasive paper .10
11.6 Procedure .10
11.6.1 Preparation of abrasive wheels .10
11.6.2 Calibration of abrasive paper .10
11.6.3 Abrasion of specimen .11
11.7 Expression of results .11
11.8 Test report .11
12 Resistance to abrasion (flooring grade laminates) .12
12.1 Principle .12
12.2 Materials .12
12.3 Apparatus .12
12.4 Test specimens .12
12.5 Preparation of specimens and abrasive paper .13
12.6 Procedure .13
12.6.1 Preparation of abrasive wheels .13
12.6.2 Calibration of abrasive paper .13
12.6.3 Abrasion of specimen .13
12.7 Expression of results .14
12.8 Test report .14
13 Resistance to immersion in boiling water .14
13.1 Principle .14
13.2 Apparatus .14
13.3 Test specimens .15
13.4 Procedure .15
13.5 Expression of results .15
13.6 Test report .16
14 Substrate protection against water vapour .16
14.1 Principle .16
14.2 Apparatus .16
14.3 Test specimens .17
14.4 Procedure .17
14.5 Expression of results .17
14.6 Test report .18
15 Resistance to water vapour .18
15.1 Principle .18
15.2 Apparatus .18
15.3 Test specimen .18
15.4 Procedure .18
15.5 Expression of results .19
15.6 Test report .19
16 Resistance to wet conditions (Exterior grade laminates).20
16.1 Principle .20
16.2 Apparatus .21
16.3 Test specimens .21
16.4 Procedure .21
16.5 Expression of results .21
16.6 Test report .22
17 Resistance to dry heat (Method A) .22
17.1 Principle .22
17.2 Apparatus and materials .22
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 4586-2:2015(E)
17.3 Test specimen .24
17.4 Test procedure .24
17.5 Examination of the test specimen .24
17.6 Expression of results .25
17.7 Test report .25
18 Resistance to dry heat (Method B) .25
18.1 Principle .25
18.2 Materials .25
18.3 Apparatus .26
18.4 Test specimen .26
18.5 Procedure .28
18.6 Expression of results .28
18.7 Test report .28
19 Dimensional stability at elevated temperature (Method A) .28
19.1 Principle .28
19.2 Apparatus .28
19.3 Test specimens .29
19.4 Procedure .29
19.5 Expression of results .29
19.6 Test report .30
20 Dimensional stability at elevated temperature (Method B) .30
20.1 Principle .30
20.2 Apparatus .30
20.3 Test specimens .31
20.4 Procedure .31
20.4.1 General.31
20.5 Expression of results .32
20.6 Test report .33
21 Dimensional stability at ambient temperature (Method A) .33
21.1 Principle .33
21.2 Apparatus .33
21.3 Test specimens .33
21.4 Procedure .33
21.5 Expression of results .34
21.6 Test report .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.