High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (usually called laminates) — Part 6: Classification and specifications for exterior-grade compact laminates of thickness 2 mm and greater

This document applies to exterior-grade compact laminates of thickness 2 mm and greater. It specifies requirements for standard and flame-retardant laminates intended for use under outdoor weather conditions such as direct sunlight, rain, and frost. Two levels of performance are specified; one for moderate exterior conditions, and the other for severe exterior conditions. ISO 4586‑2 specifies the methods of test relevant to this document.

Stratifiés décoratifs haute pression (HPL, HPDL) — Plaques à base de résines thermodurcissables (communément appelées stratifiés) — Partie 6: Classification et spécifications des stratifiés compacts pour usage en extérieur d'épaisseur égale ou supérieure à 2 mm

General Information

Status
Published
Publication Date
01-Jul-2018
Current Stage
9092 - International Standard to be revised
Start Date
25-Sep-2019
Completion Date
25-Sep-2019
Ref Project

RELATIONS

Buy Standard

Standard
REDLINE ISO 4586-6:2018 - High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (usually called laminates) — Part 6: Classification and specifications for exterior-grade compact laminates of thickness 2 mm and greater Released:7/2/2018
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4586-6:2018 - High-pressure decorative laminates (HPL, HPDL) -- Sheets based on thermosetting resins (usually called laminates)
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

ISO/TC 61/SC 11
Deleted: 06
Date: 2018‐07
Deleted: /PRF
ISO 4586-6:2018(E)
ISO/TC 61/SC 11/WG 2
Secretariat: JISC
High-pressure decorative laminates (HPL, HPDL) — Sheets based on
thermosetting resins (usually called laminates) — Part 6: Classification and
specifications for exterior-grade compact laminates of thickness 2 mm and
greater
Stratifiés décoratifs haute pression (HPL, HPDL) — Plaques à base de résines

thermodurcissables (communément appelées stratifiés) — Partie 6: Classification et

spécifications des stratifiés compacts pour usage en extérieur d’épaisseur égale ou

supérieure à 2 mm
Document type: Error! Reference source not found.
Document subtype: Error! Reference source not found.
Document stage: Error! Reference source not found.
Document language: Error! Reference source not found.

D:\temp\macroserver\DOC2PDFRGB\DOC2PDFRGB.lacroix@13422_76\C072964e_trackchanges.doc

Error! Reference source not found.
---------------------- Page: 1 ----------------------
Deleted: /PRF
ISO 4586-6:2018(E)
Contents Page

Foreword .......................................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 4

1  Scope .................................................................................................................................................................... 1

2  Normative references .................................................................................................................................... 1

3  Terms and definitions ................................................................................................................................... 1

4  Material types and classification system ................................................................................................ 2

Table 1 — Classification system ............................................................................................................................... 2

5  Requirements ................................................................................................................................................... 2

Table 2 — Dimensional tolerances ......................................................................................................................... 4

Table 3 — Physical property requirements ........................................................................................................ 4

Table 4 — Weather resistance requirements ..................................................................................................... 6

Annex A (informative) Addendum to 5.4.3, relating to fire performance ............................................... 8

Table A.1 — Typical EN 13501-1 classifications of exterior-grade compact laminates ...................... 8

Table A.2 — Examples of typical fire performance of exterior-grade compact laminates ................. 8

Table A.3 — Typical ASTM E-84 classifications of compact laminates ...................................................... 8

Annex B (informative) Assessment of conformity ........................................................................................ 10

Bibliography ................................................................................................................................................................. 11

© ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
Deleted: /PRF
ISO 4586‐6:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national

standards bodies (ISO member bodies). The work of preparing International Standards is normally

carried out through ISO technical committees. Each member body interested in a subject for which a

technical committee has been established has the right to be represented on that committee.

International organizations, governmental and non‐governmental, in liaison with ISO, also take part in

the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all

matters of electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,

Products.

This second edition cancels and replaces the first edition (ISO 4586‐6:2015), which has been technically

revised.
The main changes compared to the previous edition are as follows:
— correction of errors due to typographical, formatting, and omission issues.
A list of all parts in the ISO 4586 series can be found on the ISO website.
© ISO 2018 – All rights reserved
iii
---------------------- Page: 3 ----------------------
Deleted: /PRF
ISO 4586-6:2018(E)
Introduction

Exterior‐grade compact laminates are characterized by their high tensile strength, high impact

resistance, thermal shock resistance, and resistance to weather and corrosion. They are available in a

variety of decorative colours, with high resistance to colour change and aging in outdoor applications.

When they are self‐supporting exterior‐grade compact laminates are ready for installation, and only

require cutting to size, drilling, etc. to suit the application.

In an effort to harmonize ISO 4586 with other high‐pressure decorative laminate standards, multiple

methods may be published that demonstrate similar properties. In these instances, the same test

method title is given and is annotated as either “Method A” or “Method B”. This is the case in the

following tests: Edge squareness — 8/9, Dry heat — 17/18 Dimensional stability at elevated

temperatures — 19/20, Dimensional stability at ambient temperature — 21/22, Staining — 30/31,

Lightfastness — 32/33, Formability — 38/39, and Blistering — 40/41. In these instances, either

method may be utilized in testing. Compliance to both methods is not required. While these tests are

similar they are by no means identical and results of one method do not necessarily correspond to the

results of the accompanying test. In these situations, it is intended that the documentation in specific

parts of ISO 4586 for performance requirements be consulted. Each specific method has performance

requirements particular to that method for individual grades of high‐pressure decorative laminate.

This document has been harmonized with EN 438‐6 whenever possible.
© ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
Deleted: /PRF
INTERNATIONAL STANDARD ISO 4586‐6:2018(E)
High-pressure decorative laminates (HPL, HPDL) — Sheets
based on thermosetting resins (usually called laminates) —
Part 6: Classification and specifications for exterior-grade
compact laminates of thickness 2 mm and greater
1 Scope

This document applies to exterior‐grade compact laminates of thickness 2 mm and greater. It specifies

requirements for standard and flame‐retardant laminates intended for use under outdoor weather

conditions such as direct sunlight, rain, and frost. Two levels of performance are specified; one for

moderate exterior conditions, and the other for severe exterior conditions.
ISO 4586‐2 specifies the methods of test relevant to this document.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 178, Plastics — Determination of flexural properties

ISO 527‐2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and

extrusion plastics

ISO 1183‐1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion

method, liquid pyknometer method and titration method

ISO 4586‐2:2018, High-pressure decorative laminates (HPL) — Sheets based on thermosetting resins

Deleted: Usually
(usually called laminates) — Part 2: Determination of properties
Deleted: Laminates
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
high-pressure decorative laminate
HPL
HPDL

sheet consisting of layers of cellulosic fibrous material (normally paper) impregnated with

thermosetting resins and bonded together by the high pressure process (3.2)
Deleted: 2017
© ISO 2018 – All rights reserved
---------------------- Page: 5 ----------------------
Deleted: /PRF
ISO 4586-6:2018(E)

Note 1 to entry: This is a general definition of high‐pressure decorative laminate(s). More specific product

definitions can be found in ISO 4586‐3 to ISO 4586‐8.

Note 2 to entry: The surface layer(s) on one or both sides, having decorative colours or designs, are typically

impregnated with melamine based resins. The core layers are typically impregnated with phenolic based resins.

Note 3 to entry: The back of the sheet(s) may be made suitable for adhesive bonding to a substrate.

3.2
high-pressure process

simultaneous application of heat (temperature ≥ 120 °C) and high specific pressure (≥ 5 MPa), to

provide flowing and subsequent curing of the thermosetting resins to obtain a homogeneous non‐

porous material with increased density (≥ 1,35 g/cm), and with the required surface finish

3.3
surface layer

upper decorative layer consisting in one or more sheets of fibrous material (usually paper)

impregnated with aminoplastic thermosetting resins (usually melamine based resins) or other curable

resins or other decorative design surfaces such as metal foils, wood‐veneers, and textiles, etc. which are

not necessarily treated with thermosetting resin
3.4
core layer

fibrous material (usually paper) impregnated with thermosetting resins (usually phenolic based resins)

or other curable resins, possibly reinforced by metal layer(s) or metal mesh(es) and others which are

not necessarily treated with thermosetting resin
4 Material types and classification system

Exterior‐grade compact laminates are defined using the three letter classification system shown in

Table 1.
Table 1 — Classification system
First letter Second letter Third letter
E (Exterior grade) G (Moderate use) S (Standard grade)
or D (Severe use) or F (Flame‐retardant grade)

For example an exterior‐grade flame‐retardant HPL for severe outdoor conditions is specified as

HPL/ISO 4586‐6/EDF.

Laminate grades EGS and EGF are intended for moderate outdoor conditions, for example applications

involving medium term exposure to average levels of sunlight and weathering.

Laminate grades EDS and EDF are intended for severe outdoor conditions, for example applications

involving long term exposure to strong sunlight and weather.
5 Requirements
5.1 Compliance

Exterior‐grade compact laminate types EGS, EGF, EDS and EDF shall meet all appropriate requirements

specified in 5.2, 5.3 and 5.4. This applies to both full‐size sheets and cut‐to‐size panels.

Deleted: 2017
© ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
Deleted: /PRF
ISO 4586‐6:2018(E)
5.2 Inspection requirements
5.2.1 General

Inspection shall be carried out in accordance with ISO 4586‐2:2018, Clause 4 at a distance of 0,75 m to

1,5 m.
5.2.2 Colour and pattern

When inspected in daylight or D65 standard illuminant and again under tungsten illuminant A, there

shall be no significant difference between the corresponding colour reference sample held by the

supplier and the specimen under test.

Where colour and surface finish are critical, it is recommended that sheets be checked for colour and

surface finish compatibility before fabrication or installation.
5.2.3 Surface finish
When inspected at different viewing an
...

INTERNATIONAL ISO
STANDARD 4586-6
Second edition
2018-07
High-pressure decorative laminates
(HPL, HPDL) — Sheets based on
thermosetting resins (usually called
laminates) —
Part 6:
Classification and specifications for
exterior-grade compact laminates of
thickness 2 mm and greater
Stratifiés décoratifs haute pression (HPL, HPDL) — Plaques à base de
résines thermodurcissables (communément appelées stratifiés) —
Partie 6: Classification et spécifications des stratifiés compacts pour
usage en extérieur d'épaisseur égale ou supérieure à 2 mm
Reference number
ISO 4586-6:2018(E)
ISO 2018
---------------------- Page: 1 ----------------------
ISO 4586-6:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 4586-6:2018(E)
Contents Page

Foreword ..........................................................................................................................................................................................................................................v

Introduction ................................................................................................................................................................................................................................vi

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ................................................................................................................................... 1

3 Terms and definitions ................................................................................................................................... 1

4 Material types and classification system ................................................................................................ 2

5 Requirements .......................................................................................................................................................................................................... 3

5.1 Compliance ................................................................................................................................................................................................. 3

5.2 Inspection requirements ...................................................................................................................................3

5.2.1 General...................................................................................................................................................................................... 3

5.2.2 Colour and pattern .............................................................................................................................3

5.2.3 Surface finish ......................................................... ................................................................................3

5.2.4 Visual inspection .................................................................................................................................3

5.3 Dimensional tolerance requirements ..........................................................................................................4

5.4 Test requirements ................................................................................................................................................4

5.4.1 Physical property requirements ...................................................................................................4

5.4.2 Weather resistance requirements................................................................................................6

5.4.3 Notes on requirements for reaction to fire (see Annex A) ........................................................... 7

Annex A (informative) Addendum to 5.4.3, relating to fire performance .................................................. 8

Annex B (informative) Assessment of conformity ............................................................................................10

Bibliography .............................................................................................................................................................................................................................11

© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 4586-6:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/iso/foreword .html.

This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,

Products.

This second edition cancels and replaces the first edition (ISO 4586-6:2015), which has been technically

revised.
The main changes compared to the previous edition are as follows:
— correction of errors due to typographical, formatting, and omission issues.
A list of all parts in the ISO 4586 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 4586-6:2018(E)
Introduction

Exterior-grade compact laminates are characterized by their high tensile strength, high impact

resistance, thermal shock resistance, and resistance to weather and corrosion. They are available in a

variety of decorative colours, with high resistance to colour change and aging in outdoor applications.

When they are self-supporting exterior-grade compact laminates are ready for installation, and only

require cutting to size, drilling, etc. to suit the application.

In an effort to harmonize ISO 4586 with other high-pressure decorative laminate standards,

multiple methods may be published that demonstrate similar properties. In these instances, the

same test method title is given and is annotated as either “Method A” or “Method B”. This is the case

in the following tests: Edge squareness — 8/9, Dry heat — 17/18 Dimensional stability at elevated

temperatures — 19/20, Dimensional stability at ambient temperature — 21/22, Staining — 30/31,

Lightfastness — 32/33, Formability — 38/39, and Blistering — 40/41. In these instances, either

method may be utilized in testing. Compliance to both methods is not required. While these tests are

similar they are by no means identical and results of one method do not necessarily correspond to the

results of the accompanying test. In these situations, it is intended that the documentation in specific

parts of ISO 4586 for performance requirements be consulted. Each specific method has performance

requirements particular to that method for individual grades of high-pressure decorative laminate.

This document has been harmonized with EN 438-6 whenever possible.
© ISO 2018 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 4586-6:2018(E)
High-pressure decorative laminates (HPL, HPDL) —
Sheets based on thermosetting resins (usually called
laminates) —
Part 6:
Classification and specifications for exterior-grade
compact laminates of thickness 2 mm and greater
1 Scope

This document applies to exterior-grade compact laminates of thickness 2 mm and greater. It specifies

requirements for standard and flame-retardant laminates intended for use under outdoor weather

conditions such as direct sunlight, rain, and frost. Two levels of performance are specified; one for

moderate exterior conditions, and the other for severe exterior conditions.
ISO 4586-2 specifies the methods of test relevant to this document.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 178, Plastics — Determination of flexural properties

ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and

extrusion plastics

ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion

method, liquid pyknometer method and titration method

ISO 4586-2:2018, High-pressure decorative laminates (HPL) — Sheets based on thermosetting resins

(usually called laminates) — Part 2: Determination of properties
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at https: //www .electropedia .org/
— ISO Online browsing platform: available at https: //www .iso .org/obp
© ISO 2018 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 4586-6:2018(E)
3.1
high-pressure decorative laminate
HPL
HPDL

sheet consisting of layers of cellulosic fibrous material (normally paper) impregnated with

thermosetting resins and bonded together by the high pressure process (3.2)

Note 1 to entry: This is a general definition of high-pressure decorative laminate(s). More specific product

definitions can be found in ISO 4586-3 to ISO 4586-8.

Note 2 to entry: The surface layer(s) on one or both sides, having decorative colours or designs, are typically

impregnated with melamine based resins. The core layers are typically impregnated with phenolic based resins.

Note 3 to entry: The back of the sheet(s) may be made suitable for adhesive bonding to a substrate.

3.2
high-pressure process

simultaneous application of heat (temperature ≥ 120 °C) and high specific pressure (≥ 5 MPa), to

provide flowing and subsequent curing of the thermosetting resins to obtain a homogeneous non-

porous material with increased density (≥ 1,35 g/cm ), and with the required surface finish

3.3
surface layer

upper decorative layer consisting in one or more sheets of fibrous material (usually paper) impregnated

with aminoplastic thermosetting resins (usually melamine based resins) or other curable resins or

other decorative design surfaces such as metal foils, wood-veneers, and textiles, etc. which are not

necessarily treated with thermosetting resin
3.4
core layer

fibrous material (usually paper) impregnated with thermosetting resins (usually phenolic based resins)

or other curable resins, possibly reinforced by metal layer(s) or metal mesh(es) and others which are

not necessarily treated with thermosetting resin
4 Material types and classification system

Exterior-grade compact laminates are defined using the three letter classification system shown in

Table 1.
Table 1 — Classification system
First letter Second letter Third letter
E (Exterior grade) G (Moderate use) S (Standard grade)
or D (Severe use) or F (Flame-retardant grade)

For example an exterior-grade flame-retardant HPL for severe outdoor conditions is specified as HPL/

ISO 4586-6/EDF.

Laminate grades EGS and EGF are intended for moderate outdoor conditions, for example applications

involving medium term exposure to average levels of sunlight and weathering.

Laminate grades EDS and EDF are intended for severe outdoor conditions, for example applications

involving long term exposure to strong sunlight and weather.
2 © ISO 2018 – All rights reserved
---------------------- Page: 7 ----------------------
ISO 4586-6:2018(E)
5 Requirements
5.1 Compliance
Exterior-grade compact laminate types EGS, EGF, EDS and EDF sha
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.