ISO 17599:2015
(Main)Technical product documentation (TPD) — General requirements of digital mock-up for mechanical products
Technical product documentation (TPD) — General requirements of digital mock-up for mechanical products
ISO 17599:2015 specifies the requirements for the classification, composition, modelling, review, application, and management of digital mock-up. This International Standard for mechanical products is applicable to the building, management, review, and application of digital mock-up.
Documentation technique de produits (TPD) — Exigences générales de maquettage numérique pour les produits mécaniques
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17599
First edition
2015-01-15
Technical product documentation
(TPD) — General requirements
of digital mock-up for mechanical
products
Documentation technique de produits (TPD) — Exigences générales
de Digital mock-up pour les produits mécaniques
Reference number
©
ISO 2015
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviations. 3
5 Classification of digital mock-up . 3
5.1 Development stage . 3
5.2 Purposes . 3
5.3 Data format . 3
6 Composition of digital mock-up . 4
6.1 Geometric information . 4
6.2 Constraint information . 4
6.3 Engineering attributes . 4
7 Requirements of a digital mock-up model . 4
7.1 General principles . 4
7.2 Relationship between all kinds of digital mock-up . 4
7.3 Requirements of complete digital mock-up . 5
7.4 Requirements of sub-system digital mock-up . 5
7.5 Requirements of scheme digital mock-up . 5
7.6 Requirements of detailed digital mock-up . 5
7.7 Requirements of manufacturing digital mock-up . 6
7.8 Requirements of geometry digital mock-up . 6
7.9 Requirements of function digital mock-up . 6
7.10 Requirements of performance digital mock-up . 6
7.11 Requirements of special-purpose digital mock-up . 7
7.12 Requirements of retrofit digital mock-up . 7
8 Requirements of DMU building . 7
8.1 General requirements . 7
8.1.1 General principles . 7
8.1.2 Fundamental requirements . 7
8.1.3 Identification of parts or components . 8
8.1.4 Definition and use of coordinate system . 8
8.1.5 Colouring and texture rendering requirements . 8
8.1.6 Model state . 8
8.2 Detailed requirements of model building . 8
8.2.1 Modelling of parts . 8
8.2.2 Assembly modelling . 9
8.2.3 Simulation modelling .12
9 Simplification and lightweight models of digital mock-up .13
9.1 Application .13
9.2 General requirements .13
10 Requirements of management .13
10.1 General requirements .13
10.2 Management of the whole DMU life cycle .14
10.2.1 General principles .14
10.2.2 Management of design stage .14
10.2.3 Management of manufacture stage.15
10.2.4 Management of marketing and aftermarket stages .15
10.3 Requirements of data management .15
10.4 Configuration management .16
11 Requirements of review .16
11.1 Purposes and aims of review .16
11.2 Foundations of reviewing .16
11.3 Materials of review .17
11.4 Contents to be reviewed .17
11.4.1 Review of scheme digital mock-up .19
11.4.2 Review of detailed digital mock-up .19
11.4.3 Review of manufacturing digital mock-up.20
11.5 Body of reviewers .20
11.6 Process of review .20
11.7 Summary of review .21
11.7.1 Report of review .21
11.7.2 Conclusion of review .21
11.8 Recheck after review.21
12 Application requirements.21
12.1 General requirements .21
12.2 Detailed requirements .21
12.2.1 Design stage .21
12.2.2 Manufacture stage .23
12.2.3 Marketing stage .24
12.2.4 Aftermarket stage .24
Bibliography .25
iv © ISO 2015 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.