ISO 2974:2000

Diesel engines — High-pressure fuel injection pipe end-connections with 60 degree female cone

Moteurs diesels — Raccords finaux à cône femelle de 60 degrés pour lignes d'injection de carburant haute pression

General Information

• Status: Withdrawn
• Publication Date: 12-Apr-2000
• Withdrawal Date: 12-Apr-2000
• ICS: 43.060.40 - Fuel systems
• Technical Committee: ISO/TC 22 - Road vehicles
• Drafting Committee: ISO/TC 22 - Road vehicles
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 15-Mar-2005

Relations

• Revised: ISO 2974:2005 - Diesel engines — High-pressure fuel injection pipe end-connections with 60 degrees female cone
• Effective Date: 15-Apr-2008
• Revises: ISO 2974:1994 - Diesel engines — High-pressure fuel injection pipe end-connections with 60 degree female cone
• Effective Date: 15-Apr-2008
• Consolidated By: ISO 660:2009 - Animal and vegetable fats and oils — Determination of acid value and acidity
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2974
Fifth edition
2000-04-01
Diesel engines — High-pressure fuel
�
injection pipe end-connections with 60
female cone
Moteurs diesels — Raccords finaux à cône femelle de 60° pour lignes
d'injection de carburant haute pression
Reference number
ISO 2974:2000(E)
© ISO 2000

---------------------- Page: 1 ----------------------
ISO 2974:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-
tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem-
ber body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2000 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 2974:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commis-
sion (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 2974 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee
SC 7, Injection equipment and filters for use on road vehicles.
This fifth edition cancels and replaces the fourth edition (ISO 2974:1994), which has been technically revised.
©
ISO 2000 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 2974:2000(E)
Diesel engines — High-pressure fuel injection pipe end-
�
60
connections with female cone
1 Scope
This International Standard specifies the dimensional requirements of high-pressure pipe end-connections for diesel
(compression ignition) engine fuel injection equipment.
�
It is applicable to externally threaded end-connections of types 1 and 2 having a 60 female cone (see Figures 1 to
3), as well as to the pipe end assemblies of high-pressure fuel injection pipes with diameters of up to and including
12 mm (see Figure 4).
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publica-
tions do not apply. However, parties to agreements based on this International Standard are encouraged to investi-
gate the possibility of applying the most recent editions of the normative documents i
...