ISO 5676:2023

Tractors and machinery for agriculture and forestry — Hydraulic coupling — Braking circuit

This document specifies the conditions for interchangeability, and the operating characteristics and lays down the technical specifications for tests, for the hydraulic couplings on braking systems for towed agriculture and forestry machinery. This document applies solely to hydraulic brake couplings.

Tracteurs et matériels agricoles et forestiers — Coupleurs hydrauliques — Circuit de freinage

Le présent document spécifie les conditions d’interchangeabilité et les caractéristiques de fonctionnement des liaisons hydrauliques de freinage assisté des matériels agricoles et forestiers remorqués. Il fixe également les spécifications techniques pour les essais. Le présent document est applicable aux liaisons hydrauliques de freinage, uniquement.

General Information

• Status: Published
• Publication Date: 19-Jun-2023
• ICS: 65.060.01 - Agricultural machines and equipment in general
• Technical Committee: ISO/TC 23/SC 4 - Tractors
• Drafting Committee: ISO/TC 23/SC 4/WG 14 - Revision of ISO 17567
• Current Stage: 6060 - International Standard published
• Start Date: 20-Jun-2023
• Due Date: 05-May-2023
• Completion Date: 20-Jun-2023

Relations

• Revises: ISO 5676:1983 - Tractors and machinery for agriculture and forestry — Hydraulic coupling — Braking circuit
• Effective Date: 23-Apr-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 5676
Second edition
2023-06
Tractors and machinery for
agriculture and forestry — Hydraulic
coupling — Braking circuit
Tracteurs et matériels agricoles et forestiers — Coupleurs
hydrauliques — Circuit de freinage
Reference number
ISO 5676:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 5676:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 5676:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Characteristics and specifications .1
4.1 General . 1
4.2 Dimensional characteristics . 1
4.3 Operating characteristics and technical specifications . 2
4.3.1 Operating characteristics . 2
4.3.2 Technical specifications . 3
5 Fixing of the male half of the coupling . 3
iii
© ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO 5676:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committ
...