ISO/IEC 7816-1:2011
(Main)Identification cards — Integrated circuit cards — Part 1: Cards with contacts — Physical characteristics
Identification cards — Integrated circuit cards — Part 1: Cards with contacts — Physical characteristics
ISO/IEC 7816-1:2011 specifies the physical characteristics of integrated circuit cards with contacts. It applies to identification cards of the ID-1 card type, which can include embossing and/or a magnetic stripe and/or tactile identifier mark as specified in ISO/IEC 7811. Test methods are specified in ISO/IEC 10373-1. ISO/IEC 7816-1:2011 applies to cards which have a physical interface with electrical contacts. It does not, however, define the nature, number and position of the integrated circuits in the cards.
Cartes d'identification — Cartes à circuit intégré — Partie 1: Cartes à contacts — Caractéristiques physiques
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 7816-1
Second edition
2011-02-15
Identification cards — Integrated circuit
cards —
Part 1:
Cards with contacts — Physical
characteristics
Cartes d'identification — Cartes à circuit intégré —
Partie 1: Cartes à contacts — Caractéristiques physiques
Reference number
ISO/IEC 7816-1:2011(E)
©
ISO/IEC 2011
---------------------- Page: 1 ----------------------
ISO/IEC 7816-1:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 7816-1:2011(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 7816-1 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and personal identification.
This second edition cancels and replaces the first edition (ISO/IEC 7816-1:1998), which has been technically
revised. It also incorporates the Amendment ISO/IEC 7816-1:1998/Amd.1:2003.
ISO/IEC 7816 consists of the following parts, under the general title Identification cards — Integrated circuit
cards:
⎯ Part 1: Cards with contacts — Physical characteristics
⎯ Part 2: Cards with contacts — Dimensions and location of the contacts
⎯ Part 3: Cards with contacts — Electrical interface and transmission protocols
⎯ Part 4: Organization, security and commands for interchange
⎯ Part 5: Registration of application providers
⎯ Part 6: Interindustry data elements for interchange
⎯ Part 7: Interindustry commands for Structured Card Query Language (SCQL)
⎯ Part 8: Commands for security operations
⎯ Part 9: Commands for card management
⎯ Part 10: Electronic signals and answer to reset for synchronous cards
⎯ Part 11: Personal verification through biometric methods
⎯ Part 12: Cards with contacts — USB electrical interface and operating procedures
⎯ Part 13: Commands for application management in a multi-application environment
⎯ Part 15: Cryptographic information application
© ISO/IEC 2011 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 7816-1:2011(E)
Introduction
ISO/IEC 7816 is a series of International Standards specifying integrated circuit cards and the use of such
cards for interchange. These cards are identification cards intended for information exchange negotiated
between the outside world and the integrated circuit in the card. As a result of an information exchange, the
card delivers information (computation result, stored data) and/or modifies its content (data storage, event
memorization).
Five parts are specific to cards with galvanic contacts and three of them specify electrical interfaces.
⎯ ISO/IEC 7816-1 specifies physical characteristics for cards with contacts.
⎯ ISO/IEC 7816-2 specifies dimensions and location of the contacts.
⎯ ISO/IEC 7816-3 specifies electrical interface and transmission protocols for asynchronous cards.
⎯ ISO/IEC 7816-10 specifies electrical interface and answer to reset for synchronous cards.
⎯ ISO/IEC 7816-12 specifies electrica
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.