Coke -- Determination of bulk density in a small container

This document specifies a method for the determination of the bulk density of coke in a cubical or cylindrical container of small capacity (0,2Â m3). It is applicable to coke with a nominal top size not greater than 125Â mm.

Coke -- Détermination de la masse volumique en vrac dans un récipient de petites dimensions

General Information

Status
Published
Publication Date
26-Aug-2021
Technical Committee
Drafting Committee
Current Stage
5060 - Close of voting Proof returned by Secretariat
Start Date
28-Jul-2021
Completion Date
28-Jul-2021
Ref Project

RELATIONS

Buy Standard

Standard
ISO 567:2021 - Coke -- Determination of bulk density in a small container
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/PRF 567:Version 10-jul-2021 - Coke -- Determination of bulk density in a small container
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 567
Third edition
2021-08
Coke — Determination of bulk density
in a small container
Coke — Détermination de la masse volumique en vrac dans un
récipient de petites dimensions
Reference number
ISO 567:2021(E)
ISO 2021
---------------------- Page: 1 ----------------------
ISO 567:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 567:2021(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Apparatus ..................................................................................................................................................................................................................... 1

6 Test sample ................................................................................................................................................................................................................. 2

7 Procedure..................................................................................................................................................................................................................... 2

8 Expression of results ........................................................................................................................................................................................ 2

9 Precision ....................................................................................................................................................................................................................... 3

9.1 Repeatability ............................................................................................................................................................................................. 3

9.2 Reproducibility ....................................................................................................................................................................................... 3

10 Test report ................................................................................................................................................................................................................... 3

Bibliography ................................................................................................................................................................................................................................ 4

© ISO 2021 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 567:2021(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 27, Coal and coke, Subcommittee SC 3,

Coke.

This third edition cancels and replaces the second edition (ISO 567:1995), which has been technically

revised.
The main changes compared to the previous edition are as follows:
— General and technical revision.

— The container to be used for determination of coke bulk density can either be cubical or cylindrical

in shape with a capacity 0,2 m .

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 567:2021(E)
Introduction

The bulk density of coke depends on its physical characteristics, e.g. apparent relative density, shape

and size of the coke particles, and on the dimensions of the container. The container specified in this

International Standard has a capacity of 0,2 m . The
...

INTERNATIONAL ISO
STANDARD 567
Third edition
Coke — Determination of bulk density
in a small container
Coke — Détermination de la masse volumique en vrac dans un
récipient de petites dimensions
PROOF/ÉPREUVE
Reference number
ISO 567:2021(E)
ISO 2021
---------------------- Page: 1 ----------------------
ISO 567:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 567:2021(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Apparatus ..................................................................................................................................................................................................................... 1

6 Test sample ................................................................................................................................................................................................................. 2

7 Procedure..................................................................................................................................................................................................................... 2

8 Expression of results ........................................................................................................................................................................................ 2

9 Precision ....................................................................................................................................................................................................................... 3

9.1 Repeatability limit ................................................................................................................................................................................ 3

9.2 Reproducibility ....................................................................................................................................................................................... 3

10 Test report ................................................................................................................................................................................................................... 3

Bibliography ................................................................................................................................................................................................................................ 4

© ISO 2021 – All rights reserved PROOF/ÉPREUVE iii
---------------------- Page: 3 ----------------------
ISO 567:2021(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 27, Coal and coke, Subcommittee SC 3,

Coke.

This third edition cancels and replaces the second edition (ISO 567:1995), which has been technically

revised.
The main changes compared to the previous edition are as follows:
— General and technical revision;

— The container to be used for determination of coke bulk density can either be cubical or cylindrical

in shape with a capacity 0,2 m .

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/ members .html.
iv PROOF/ÉPREUVE © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 567:2021(E)
Introduction

The bulk density of coke depends on its physical characteristics, e.g. apparent relative density, shape

and size of the coke particles, and on the dimensions of the container. The container specified in this

International Standard has a capacity of 0,2 m . The determination of bulk density of co

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.