ISO 11114-1:2020/Amd 1:2023
(Amendment)Gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 1: Metallic materials — Amendment 1
Gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 1: Metallic materials — Amendment 1
Bouteilles à gaz — Compatibilité des matériaux des bouteilles et des robinets avec les contenus gazeux — Partie 1: Matériaux métalliques — Amendement 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 11114-1
Third edition
2020-05
AMENDMENT 1
2023-07
Gas cylinders — Compatibility of
cylinder and valve materials with gas
contents —
Part 1:
Metallic materials
AMENDMENT 1
Bouteilles à gaz — Compatibilité des matériaux des bouteilles et des
robinets avec les contenus gazeux —
Partie 1: Matériaux métalliques
AMENDEMENT 1
Reference number
ISO 11114-1:2020/Amd.1:2023(E)
ISO 11114-1:2020/Amd.1:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 11114-1:2020/Amd.1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 23, Transportable gas
cylinders, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
A list of all parts in the ISO 11114 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iii
ISO 11114-1:2020/Amd.1:2023(E)
Gas cylinders — Compatibility of cylinder and valve
materials with gas contents —
Part 1:
Metallic materials
AMENDMENT 1
6.3.2, Table 1
Replace the rows corresponding to Gas numbers 5, 6, 49, 58, 59, 61, 62, 63 with the following:
ISO 11114-1:2020/Amd.1:2023(E)
Table 1 — Gas/material compatibility
No. Gas number Name Formula Key compatibility characteristics Material
UN number
Cylinder Valve (body and
components)
A N A N
5 (UN 1741) BORON TRICHLORIDE BCl Hydrolyses to hydrogen chloride in contact with NS AA CS AA
moisture. In wet conditions, see specific risk of
QTS SS B
hydrogen chloride compatibility, i.e. severe corro-
SS Ni
sion of most of the materials and risk of hydrogen
embrittlement.
Ni ASB
Mixtures of dry gas not exceeding 0,1 % of this gas
may be filled into AA cylinders.
6 (UN 1008) BORON TRIFLUORIDE BF Hydrolyses to hydrogen fluoride in contact with NS AA CS AA
moisture. In wet conditions, see specific risk of
QTS SS B
hydrogen fluoride compatibility, i.e. severe corro-
SS Ni
sion of most of the materials and risk of hydrogen
embrittlement.
Ni ASB
Mixtures containing less than 0,1 % BF may be
filled into AA cylinders.
49 (UN 1045) FLUORINE F Hydrolyses to hydrogen fluoride in contact with QTS AA CS AA
moisture. In wet conditions, see specific risk of
a
NS SS B
hydrogen fluoride compatibility, i.e. severe corro-
SS Ni
sion of most of the materials and risk of hydrogen
embrittlement.
Ni ASB
Risk of violent reaction with AA.
Recommended materials are also Ni alloy and re-
fined nickel.
Mixtures containing less than 0,1 % of this gas may
be filled into AA cylinders.
NOTE Incoloy© and Hastelloy© are examples of suitable products available commercially. This information is given for the convenience of users of this document and does not
constitute an endorsement by ISO of these products.
a
Brass is only acceptable as a valve body but not as a general valve component material.
b
For mixtures containing up to 1 000 ppm of dry NO, brass valves can be used.
ISO 11114-1:2020/Amd.1:2023(E)
Table 1 (continued)
No. Gas number Name Formula Key compatibility characteristics Material
UN number
Cylinder Valve (body and
components)
A N A N
58 (UN 1048) HYDROGEN BROMIDE HBr This compound is highly hygroscopic and corrosive NS AA CS B
in wet conditions with most of the materials except
QTS SS AA
some high corrosion resistant nickel alloys (e.g.
SS Ni
Hastelloy©). QTS are limited to a maximum ulti-
mate tensile strength of 950 MPa. This limitation
Ni ASB
also applies to mixtures containing the gas stored
at a total pressure at 15 °C greater than half the
normal service pressure of the cylinder.
However, experience shows that a cylinder can be
safely used without any specific strength limitation
requirements, providing the maximum working
pressure at 15 °C in the cylinder is less than one-
fifth of the test pressure (TP/5), in order to main-
tain a low stress level in the cylinder material.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.