ISO 16032:2004
(Main)Acoustics — Measurement of sound pressure level from service equipment in buildings — Engineering method
Acoustics — Measurement of sound pressure level from service equipment in buildings — Engineering method
ISO 16032:2004 specifies methods for measuring the sound-pressure level produced by service equipment attached to or installed in buildings. It specifically covers measurements on sanitary installations, mechanical ventilation, heating and cooling service equipment, lifts, rubbish chutes, boilers, blowers, pumps and other auxiliary service equipment, and motor-driven car park doors, but can also be applied to other equipment attached to or installed in buildings. The methods are suitable for rooms with volumes of approximately 300 cubic metres or less in e.g. dwellings, hotels, schools, offices and hospitals. The standard is not in general intended for measurements in large auditoria such as concert halls. However, the operating conditions and operating cycles in Annex B can be used in such cases. The service equipment sound-pressure level is determined as the maximum A-weighted and optionally C-weighted sound-pressure level occurring during a specified operation cycle of the service equipment under test, or as the equivalent continuous sound-pressure level determined with a specified integration time. A-weighted and C-weighted values are calculated from octave-band measurements.
Acoustique — Mesurage du niveau de pression acoustique des équipements techniques dans les bâtiments — Méthode d'expertise
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 16032
First edition
2004-09-15
Acoustics — Measurement of sound
pressure level from service equipment in
buildings — Engineering method
Acoustique — Mesurage du niveau de pression acoustique des
équipements techniques dans les bâtiments — Méthode d'expertise
Reference number
ISO 16032:2004(E)
©
ISO 2004
---------------------- Page: 1 ----------------------
ISO 16032:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 16032:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16032 was prepared by the European Committee for Standardization (CEN) in collaboration with
Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 2, Building acoustics, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Throughout the text of this document, read “.this European Standard.” to mean “.this International
Standard.”.
© ISO 2004 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 16032:2004(E)
Contents page
Foreword.v
Introduction .vi
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Instrumentation.4
5 Test method – General .5
6 Measurement procedure.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.