ISO 374-6:2025
(Main)Protective gloves against dangerous chemicals and micro-organisms — Part 6: Protective gloves for hairdressers
Protective gloves against dangerous chemicals and micro-organisms — Part 6: Protective gloves for hairdressers
This document specifies the requirements for protective gloves to protect the hairdressers especially from the risk associated with micro-organisms and dangerous chemicals and defines terms to be used.
Gants de protection contre les produits chimiques dangereux et les micro-organismes — Partie 6: Gants de protection pour les coiffeurs
Le présent document spécifie les exigences relatives aux gants de protection destinés à protéger les coiffeurs, notamment contre les risques liés aux micro-organismes et aux produits chimiques dangereux, et définit les termes à utiliser.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 374-6
First edition
Protective gloves against dangerous
2025-07
chemicals and micro-organisms —
Part 6:
Protective gloves for hairdressers
Gants de protection contre les produits chimiques dangereux et
les micro-organismes —
Partie 6: Gants de protection pour les coiffeurs
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Performance requirement. 2
4.1 General requirements .2
4.2 Determination of removable surface powder .3
4.3 Glove length .3
4.4 Mechanical strength .3
4.5 Resistance to microorganisms .3
4.6 Permeation .3
5 Test methods . 4
5.1 Mechanical strength .4
5.1.1 Conditioning .4
5.1.2 Sampling .4
5.1.3 Test method for mechanical strength .6
5.2 Permeation test .6
5.2.1 Conditioning .6
5.2.2 Test procedure.6
6 Marking . . 7
7 Information supplied by the manufacturer . 8
Bibliography . 9
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had notreceived notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Personal protective
equipment, Subcommittee SC 13, Protective clothing, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 162, Protective clothing including hand and arm
protection and lifejackets, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 374-6:2025(en)
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6:
Protective gloves for hairdressers
Warning — Persons using this standard shall be familiar with normal laboratory practice. This
document does not purport to address all the safety problems, if any, associated with its use. It is the
responsibility of the user to apply established Health and Safety practices and to ensure compliance
with European or national regulatory conditions.
1 Scope
This document specifies the requirements for protective gloves to protect the hairdressers especially from
the risk associated with micro-organisms and dangerous chemicals and defines terms to be used.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 374-1:2024, Protective gloves against chemicals and micro-organisms — Part 1 terminology and
performance requirements for chemical risks
ISO 374-2:2019, Protective gloves against dangerous chemicals and micro-organisms — Part 2: Determination
of resistance to penetration
ISO 374-5:2024, Protective gloves against dangerous chemicals and micro-organisms — Part 5 terminology and
performance requirements for micro-organisms risks
ISO 6529:2013, Protective clothing — Protection against chemicals — Determination of resistance of protective
clothing materials to permeation by liquids and gases
ISO 7000:2019, Graphical symbols for use on equipment — Registered symbols
ISO 21171:2006, Medical gloves — Determination of removable surface powder
ISO 21420:2020, Protective gloves — General requirements and test methods
ISO 21420:2020+Amd 1:2022, Protective gloves — General requirements and test methods — Amendment 1
EN 16523-1:2015+Amd 1:2018, Determination of material resistance to permeation by chemicals — Part 1:
Permeation by liquid chemical under conditions of continuous contact
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 16523-1+Amd 1:2018,
ISO 374-1:2024 and ISO 374-5:2024 and the following apply.
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
protective gloves for hairdressers
gloves to protect the skin of the hairdresser during the handling of chemicals and the use of water during
their work (colouring, discolouring, curling, washing…)
3.2
protective glove material
any material or combination of materials used in a protective glove for the purpose of isolating the hands or
hands and arms from direct contact with a dangerous chemical
3.3
degradation
deleterious change in one or more properties of a protective glove material (3.2) due to contact with a
chemical
Note 1 to entry: Indications of degradation may include flaking, swelling, disintegration, embrittlement, colour change,
dimensional change, appearance, hardening, softening, etc.
3.4
permeation
process by which a chemical moves through a protective glove material (3.2) on a molecular level
Note 1 to entry: Permeation involves the following:
— absorption of molecules of the chemical into the contacted (outside) surface of a material;
— diffusion of the absorbed molecules in the material;
— desorption of the molecules from the opposite (inside) surface of the material.
3.5
test chemical
chemical substance, or mixture of chemical substances, potentially hazardous to health that is used under
laboratory test conditions to determine the breakthrough time
3.6
single use hairdressers’ glove
non-reusable glove designed to be used on one individual by a hairdresser during a single-term task
4 Performance requirement
4.1 General requirements
All tests required in this standard shall be performed on unused gloves unless otherwise specified.
Hairdresser’s protective gloves shall meet all the applicable requirements of ISO 21420:2020+Amd1:2022.
Special additional requirements are defined in this document (e.g., minimum length of the gloves).
The gloves for hairdressers are single use gloves:
— They shall not include seams or be welded.
— They shall be used for one task and on one client only and for a maximum time of 60 min.
The gloves for hairdressers shall be conform to the requirement specified in 4.2, 4.3, 4.4, 4.5 and 4.6.
4.2 Determination of removable surface powder
The gloves shall be powder-free, which means that the total quantity of powder residues determined
according to the test method B in ISO 21171:2006, 9.2, 9.3 and 9.4 shall not exceed 2 mg per glove.
Any glove containing more than 2 mg powder is categorised as a powdered glove and it fails the requirement.
4.3 Glove length
The glove length shall be measured according to ISO 21420:2020, 6.1.
The minimum length of the glove depends on the claimed protection area.
For type 240, hand protection only, the minimum glove length is 240 mm.
For type 300, hand and forearm protection only, the minimum glove length is 300 mm.
4.4 Mechanical strength
The glove shall have a sufficient robustness. Different glove materials require different force at break
requirements to ensure an acceptable performance. Absolute force at break values do not directly correlate
with the in-use performance. Selection of appropriate glove materials for the intended application shall be
part of the risk management process.
When tested according to 5.1, the gloves for hairdressers shall have a force at break in accordance with the
value given in Table 1.
Table 1 — Force at break re
...
Norme
internationale
ISO 374-6
Première édition
Gants de protection contre les
2025-07
produits chimiques dangereux et
les micro-organismes —
Partie 6:
Gants de protection pour les
coiffeurs
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6: Protective gloves for hairdressers
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2025
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Exigence de performance . 2
4.1 Exigences générales .2
4.2 Détermination de la poudre résiduelle en surface .3
4.3 Longueur du gant .3
4.4 Résistance mécanique.3
4.5 Résistance aux micro-organismes .4
4.6 Perméation .4
5 Méthodes d'essai . 5
5.1 Résistance mécanique.5
5.1.1 Conditionnement .5
5.1.2 Échantillonnage.5
5.1.3 Méthode d'essai pour la résistance mécanique .7
5.2 Essai de perméation .7
5.2.1 Conditionnement .7
5.2.2 Mode opératoire d'essai .7
6 Marquage . 8
7 Informations fournies par le fabricant . 9
Bibliographie .11
iii
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'ISO attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation
d'un ou de plusieurs brevets. L'ISO ne prend pas position quant à la preuve, à la validité et à l'applicabilité
de tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l'ISO
n'avait pas reçu notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application.
Toutefois, il y a lieu d'avertir les responsables de la mise en application du présent document que des
informations plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à
l'adresse www.iso.org/brevets. L'ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou
partie de tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 94, Sécurité individuelle — Equipement de
protection individuelle, sous-comité SC 13, Vêtements de protection, en collaboration avec le comité technique
CEN/TC 162, Vêtements de protection, y compris la protection de la main et du bras et y compris les gilets de
sauvetage, du Comité européen de normalisation (CEN), conformément à l'Accord de coopération technique
entre l'ISO et le CEN (Accord de Vienne).
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l'adresse www.iso.org/fr/members.html.
iv
Norme internationale ISO 374-6:2025(fr)
Gants de protection contre les produits chimiques dangereux
et les micro-organismes —
Partie 6:
Gants de protection pour les coiffeurs
AVERTISSEMENT — Les utilisateurs de la présente norme doivent bien connaître les pratiques
courantes de laboratoire. Le présent document n'a pas pour but de traiter tous les problèmes de
sécurité qui sont, le cas échéant, liés à son utilisation. Il est de la responsabilité de l'utilisateur
d'appliquer des méthodes d'hygiène et de sécurité appropriées et d'assurer leur conformité aux
règlements nationaux ou européens existants.
1 Domaine d'application
Le présent document spécifie les exigences relatives aux gants de protection destinés à protéger les coiffeurs,
notamment contre les risques liés aux micro-organismes et aux produits chimiques dangereux, et définit les
termes à utiliser.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu'ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l'édition citée s'applique. Pour
les références non datées, la dernière édition du document de référence s'applique (y compris les éventuels
amendements).
ISO 374-1:2024, Gants de protection contre les produits chimiques dangereux et les micro-organismes — Partie
1: Terminologie et exigences de performance pour les risques chimiques
ISO 374-2:2019, Gants de protection contre les produits chimiques dangereux et les micro-organismes — Partie
2: Détermination de la résistance à la pénétration
ISO 374-5:2024, Gants de protection contre les produits chimiques dangereux et les micro-organismes — Partie
5: Terminologie et exigences de performance pour les risques par les micro-organismes
ISO 6529:2013, Vêtements de protection — Protection contre les produits chimiques — Détermination de la
résistance des matériaux utilisés pour la confection des vêtements de protection à la perméation par des liquides
et des gaz
ISO 7000:2019, Symboles graphiques utilisables sur le matériel — Symboles enregistrés
ISO 21171:2006, Gants à usage médical — Détermination de la poudre résiduelle en surface
ISO 21420:2020, Gants de protection — Exigences générales et méthodes d’essai
ISO 21420:2020+Amd 1:2022, Gants de protection — Exigences générales et méthodes d’essai — Amendement 1
EN 16523-1:2015+Amd 1:2018, Détermination de la résistance des matériaux à la perméation par des produits
chimiques — Partie 1: Perméation par des produits chimiques liquides potentiellement dangereux dans des
conditions de contact continu
3 Termes et définitions
Pour les besoins du présent document, les termes et les définitions de l'EN 16523-1+Amd 1:2018,
l’ISO 374-1:2024 et l'ISO 374-5:2024 ainsi que les termes et définitions suivants s'appliquent.
Pour les besoins du présent document, les termes et définitions suivants s'appliquent.
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en normalisation,
consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l'adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l'adresse https:// www .electropedia .org/
3.1
gants de protection pour les coiffeurs
gants pour protéger la peau du coiffeur lors de la manipulation de produits chimiques et de l'utilisation d'eau
pendant son travail (coloration, décoloration, frisage, lavage…)
3.2
matériau d'un gant de protection
tout matériau ou combinaison de matériaux utilisés dans un gant de protection dans le but d'isoler les mains,
ou les mains et les bras, d'un contact direct avec un produit chimique dangereux
3.3
dégradation
transformation avec détérioration d'une ou de plusieurs propriétés du matériau d'un gant de protection (3.2),
suite au contact d'un produit chimique
Note 1 à l'article: Les signes de dégradation peuvent inclure l'écaillement, le gonflement, la désintégration, la
fragilisation, la variation de couleur, les variations dimensionnelles, l'aspect, le durcissement, le ramollissement, etc.
3.4
perméation
processus par lequel un produit chimique migre à travers le matériau d'un gant de protection (3.2) à l'échelle
moléculaire
Note 1 à l'article: La perméation implique:
— l'absorption des molécules du produit chimique dans la surface de contact (extérieure) d'un matériau;
— la diffusion des molécules absorbées dans le matériau;
— désorption des molécules de la surface opposée (intérieure) du matériau.
3.5
produit chimique d'essai
substance chimique ou mélange de substances chimiques potentiellement dangereuses pour la santé, qui est
utilisé, dans les conditions d'essai en laboratoire, pour déterminer le temps de passage
3.6
gant pour coiffeurs à usage unique
gant non réutilisable conçu pour être utilisé par un coiffeur sur une personne pendant une tâche à durée unique
4 Exigence de performance
4.1 Exigences générales
Tous les essais requis dans la présente norme doivent être effectués sur des gants non utilisés, sauf
spécification contraire.
Les gants de protection pour coiffeurs doivent satisfaire à toutes les exigences applicables de
l'ISO 21420:2020+Amd 1:2022.
Des exigences supplémentaires particulières sont définies dans le présent document (la longueur minimale
des gants, par exemple).
Les gants pour coiffeurs sont des gants à usage unique:
— ils ne doivent pas comporter de coutures ni être soudés;
— ils doivent être utilisés pour une seule tâche, pour un seul client et pour une durée maximale de
...
FINAL DRAFT
International
Standard
ISO/FDIS 374-6
ISO/TC 94/SC 13
Protective gloves against dangerous
Secretariat: SNV
chemicals and micro-organisms —
Voting begins on:
2025-05-07
Part 6:
Protective gloves for hairdressers
Voting terminates on:
2025-07-02
Gants de protection contre les produits chimiques dangereux et
les micro-organismes —
Partie 6: Gants de protection pour les coiffeurs
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 374-6:2025(en) © ISO 2025
FINAL DRAFT
ISO/FDIS 374-6:2025(en)
International
Standard
ISO/FDIS 374-6
ISO/TC 94/SC 13
Protective gloves against dangerous
Secretariat: SNV
chemicals and micro-organisms —
Voting begins on:
Part 6:
Protective gloves for hairdressers
Voting terminates on:
Gants de protection contre les produits chimiques dangereux et
les micro-organismes —
Partie 6: Gants de protection pour les coiffeurs
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 374-6:2025(en) © ISO 2025
ii
ISO/FDIS 374-6:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Performance requirement. 2
4.1 General requirements .2
4.2 Determination of removable surface powder .3
4.3 Glove length .3
4.4 Mechanical strength .3
4.5 Resistance to microorganisms .3
4.6 Permeation .3
5 Test methods . 4
5.1 Mechanical strength .4
5.1.1 Conditioning .4
5.1.2 Sampling .4
5.1.3 Test method for mechanical strength .6
5.2 Permeation test .6
5.2.1 Conditioning .6
5.2.2 Test procedure.6
6 Marking . . 7
7 Information supplied by the manufacturer . 8
Annex ZA (informative) Relationship between this European Standard and Essential
Requirements of Regulation 2016/425 aimed to be covered . 9
Bibliography .12
iii
ISO/FDIS 374-6:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had notreceived notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Protective clothing
and equipment, Subcommittee SC 13, Protective clothing, in collaboration with the European Committee
for Standardization (CEN) Technical Committee CEN/TC 162, Protective clothing including hand and arm
protection and lifejackets, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
FINAL DRAFT International Standard ISO/FDIS 374-6:2025(en)
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6:
Protective gloves for hairdressers
Warning — Persons using this standard shall be familiar with normal laboratory practice. This
document does not purport to address all the safety problems, if any, associated with its use. It is the
responsibility of the user to apply established Health and Safety practices and to ensure compliance
with European or national regulatory conditions.
1 Scope
This document specifies the requirements for protective gloves to protect the hairdressers especially from
the risk associated with micro-organisms and dangerous chemicals and defines terms to be used.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 374-1:2024, Protective gloves against chemicals and micro-organisms — Part 1 terminology and
performance requirements for chemical risks
ISO 374-2:2019, Protective gloves against dangerous chemicals and micro-organisms — Part 2: Determination
of resistance to penetration
ISO 374-5:2024, Protective gloves against dangerous chemicals and micro-organisms — Part 5 terminology and
performance requirements for micro-organisms risks
ISO 6529:2013, Protective clothing — Protection against chemicals — Determination of resistance of protective
clothing materials to permeation by liquids and gases
ISO 7000:2019, Graphical symbols for use on equipment — Registered symbols
ISO 21171:2006, Medical gloves — Determination of removable surface powder
ISO 21420:2020, Protective gloves — General requirements and test methods
ISO 21420:2020+Amd 1:2022, Protective gloves — General requirements and test methods — Amendment 1
EN 16523-1:2015+Amd 1:2018, Determination of material resistance to permeation by chemicals — Part 1:
Permeation by liquid chemical under conditions of continuous contact
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 16523-1+Amd 1:2018,
ISO 374-1:2024 and ISO 374-5:2024 and the following apply.
For the purposes of this document, the following terms and definitions apply.
ISO/FDIS 374-6:2025(en)
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
protective gloves for hairdressers
gloves to protect the skin of the hairdresser during the handling of chemicals and the use of water during
their work (colouring, discolouring, curling, washing…)
3.2
protective glove material
any material or combination of materials used in a protective glove for the purpose of isolating the hands or
hands and arms from direct contact with a dangerous chemical
3.3
degradation
deleterious change in one or more properties of a protective glove material (3.2) due to contact with a
chemical
Note 1 to entry: Indications of degradation may include flaking, swelling, disintegration, embrittlement, colour change,
dimensional change, appearance, hardening, softening, etc.
3.4
permeation
process by which a chemical moves through a protective glove material (3.2) on a molecular level
Note 1 to entry: Permeation involves the following:
— absorption of molecules of the chemical into the contacted (outside) surface of a material;
— diffusion of the absorbed molecules in the material;
— desorption of the molecules from the opposite (inside) surface of the material.
3.5
test chemical
chemical substance, or mixture of chemical substances, potentially hazardous to health that is used under
laboratory test conditions to determine the breakthrough time
3.6
single use hairdressers’ glove
non-reusable glove designed to be used on one individual by a hairdresser during a single-term task
4 Performance requirement
4.1 General requirements
All tests required in this standard shall be performed on unused gloves unless otherwise specified.
Hairdress
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
ISO/FDIS 374-6
Style Definition
...
ISO/TC 94/SC 13
Style Definition
...
Style Definition
...
Date: 2024-05-02
Style Definition
...
ISO/FDIS 374-6:2024(en)
Style Definition
...
Style Definition
Secretariat: SNV
...
Style Definition
...
Date: 2025-xx
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Protective gloves against dangerous chemicals and micro-organisms
Style Definition
...
- —
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Part 6: —
Style Definition
...
Protective gloves for hairdressers
Style Definition
...
Style Definition
...
Gants de protection contre les produits chimiques dangereux et les micro-organismes – —
Style Definition
...
Partie 6: GantGants de protection pour les coiffeurs
Style Definition
...
Style Definition
...
CCMC will prepare and attach the official title page.
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
Formatted
...
FDIS stage
ISO/FDIS 374-6:2025(en)
Commented [eXtyles1]: The reference "ISO
2024" is to a withdrawn standard
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
Formatted: Default Paragraph Font
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
Formatted: Adjust space between Latin and
at the address below or ISO'sISO’s member body in the country of the requester.
Asian text, Adjust space between Asian text
and numbers
ISO Copyright Officecopyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Formatted: zzCopyright address, Adjust space
Phone: + 41 22 749 01 11
between Latin and Asian text, Adjust space
between Asian text and numbers
Email: copyright@iso.org
E-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Commented [eXtyles2]: The URL
https://www.iso.org/ has been redirected to
Published in Switzerland.
https://www.iso.org/home.html. Please verify the
URL.
Formatted: zzCopyright address, Adjust space
between Latin and Asian text, Adjust space
between Asian text and numbers
iii
ISO/FDIS 374-6:2025(en)
Contents Page Formatted: Adjust space between Latin and
Asian text, Adjust space between Asian text
and numbers, Tab stops: Not at 17.2 cm
Foreword . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Performance requirement . 3
4.1 General requirements . 3
4.2 Determination of removable surface powder . 3
4.3 Glove length . 3
4.4 Mechanical strength . 3
4.5 Resistance to microorganisms . 4
4.6 Permeation . 4
5 Test methods . 5
5.1 Mechanical strength . 5
5.2 Permeation test . 7
6 Marking . 8
7 Information supplied by the manufacturer . 10
Annex ZA (informative) Relationship between this European Standard and Essential
Requirements of Regulation 2016/425 aimed to be covered . 12
Bibliography . 15
iv
ISO/FDIS 374-6:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had notreceived notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Protective clothing and
equipment, Subcommittee SC 13, Protective clothing, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 162, Protective clothing including hand and arm
protection and lifejackets, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
ISO/DIS 374-6:2023(E)
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Performance requirement . 5
4.1 General requirements . 5
4.2 Glove's length. 5
4.3 Mechanical strength . 5
Table 1 — Force at break requirements . 6
4.4 Resistance to microorganisms . 6
4.5 Permeation . 6
Table 2 — List of test chemicals . 6
5 Test methods . 7
5.1 Mechanical strength . 7
5.1.1 Conditioning . 7
5.1.2 Sampling . 7
5.1.3 Test method for mechanical strength . 8
5.2 Permeation test. 9
5.2.1 Conditioning . 9
5.2.2 Test procedure . 9
6 Marking .10
7 Information supplied by the manufacturer .11
Annex ZA (informative) Relationship between this European Standard and Essential
Requirements of Regulation 2016/425 aimed to be covered .12
Table ZA.1 — Correspondence between this European Standard and Annex II of
Regulation 2016/425.12
ii
ISO/FDIS 374-6:2024(en)
European foreword
iii
FINAL DRAFT International Standard ISO/FDIS 374-6:2024(en)
Formatted: Main Title 2
Protective gloves against dangerous chemicals and micro-organisms
Formatted: Adjust space between Latin and
- —
Asian text, Adjust space between Asian text
and numbers
Part 6: — Formatted: Default Paragraph Font
Protective gloves for hairdressers
Formatted: Default Paragraph Font
Formatted: Default Paragraph Font, Font:
Warning: — Persons using this standard shall be familiar with normal laboratory practice. This
Formatted: Adjust space between Latin and
document does not purport to address all the safety problems, if any, associated with its use. It is the
Asian text, Adjust space between Asian text
responsibility of the user to apply established Health and Safety practices and to ensure compliance
and numbers, Tab stops: Not at 0.7 cm + 1.4
with European or national regulatory conditions.
cm + 2.1 cm + 2.8 cm + 3.5 cm + 4.2 cm + 4.9
cm + 5.6 cm + 6.3 cm + 7 cm
1 Scope
Commented [eXtyles3]: Not found, but similar
This document specifies the requirements for protective gloves to protect the hairdressers especially from the
references exist
risk associated with micro-organisms and dangerous chemicals and defines terms to be used.
ISO 374-1:2016, Protective gloves against
2 Normative references
dangerous chemicals and micro-organisms — Part
1: Terminology and performance requirements for
The following documents are referred to in the text in such a way that some or all of their content constitutes
chemical risks
requirements of this document. For dated references, only the edition cited applies. For undated references,
Formatte
...
PROJET FINAL
Norme
internationale
ISO/FDIS 374-6
ISO/TC 94/SC 13
Gants de protection contre les
Secrétariat: SNV
produits chimiques dangereux et
Début de vote:
les micro-organismes —
2025-05-07
Partie 6:
Vote clos le:
2025-07-02
Gants de protection pour les
coiffeurs
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6: Protective gloves for hairdressers
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
Numéro de référence
ISO/FDIS 374-6:2025(fr) © ISO 2025
PROJET FINAL
ISO/FDIS 374-6:2025(fr)
Norme
internationale
ISO/FDIS 374-6
ISO/TC 94/SC 13
Gants de protection contre les
Secrétariat: SNV
produits chimiques dangereux et
Début de vote:
les micro-organismes —
2025-05-07
Partie 6:
Vote clos le:
2025-07-02
Gants de protection pour les
coiffeurs
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6: Protective gloves for hairdressers
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
© ISO 2025 INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
NORMES POUVANT
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse Numéro de référence
ISO/FDIS 374-6:2025(fr) © ISO 2025
ii
ISO/FDIS 374-6:2025(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Exigence de performance . 2
4.1 Exigences générales .2
4.2 Détermination de la poudre résiduelle en surface .3
4.3 Longueur du gant .3
4.4 Résistance mécanique.3
4.5 Résistance aux micro-organismes .4
4.6 Perméation .4
5 Méthodes d'essai . 5
5.1 Résistance mécanique.5
5.1.1 Conditionnement .5
5.1.2 Échantillonnage.5
5.1.3 Méthode d'essai pour la résistance mécanique .6
5.2 Essai de perméation .7
5.2.1 Conditionnement .7
5.2.2 Mode opératoire d'essai .7
6 Marquage . 7
7 Informations fournies par le fabricant . 8
Annexe ZA (informative) Relation entre la présente Norme européenne et les exigences
essentielles concernées du Règlement (UE) 2016/425 .10
Bibliographie .13
iii
ISO/FDIS 374-6:2025(fr)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'ISO attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation
d'un ou de plusieurs brevets. L'ISO ne prend pas position quant à la preuve, à la validité et à l'applicabilité
de tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l'ISO
n'avait pas reçu notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application.
Toutefois, il y a lieu d'avertir les responsables de la mise en application du présent document que des
informations plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à
l'adresse www.iso.org/brevets. L'ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou
partie de tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 94, Sécurité individuelle — Vêtements
et équipements de protection, sous-comité SC 13, Vêtements de protection, en collaboration avec le comité
technique CEN/TC 162 Vêtements de protection, y compris la protection de la main et du bras et y compris les
gilets de sauvetage, du Comité européen de normalisation (CEN), conformément à l'Accord de coopération
technique entre l'ISO et le CEN (Accord de Vienne).
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l'adresse www.iso.org/fr/members.html.
iv
PROJET FINAL Norme internationale ISO/FDIS 374-6:2025(fr)
Gants de protection contre les produits chimiques dangereux
et les micro-organismes —
Partie 6:
Gants de protection pour les coiffeurs
AVERTISSEMENT — Les utilisateurs de la présente norme doivent bien connaître les pratiques
courantes de laboratoire. Le présent document n'a pas pour but de traiter tous les problèmes de
sécurité qui sont, le cas échéant, liés à son utilisation. Il est de la responsabilité de l'utilisateur
d'appliquer des méthodes d'hygiène et de sécurité appropriées et d'assurer leur conformité aux
règlements nationaux ou européens existants.
1 Domaine d'application
Le présent document spécifie les exigences relatives aux gants de protection destinés à protéger les coiffeurs,
notamment contre les risques liés aux micro-organismes et aux produits chimiques dangereux, et définit les
termes à utiliser.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu'ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l'édition citée s'applique. Pour
les références non datées, la dernière édition du document de référence s'applique (y compris les éventuels
amendements).
ISO 374-1:2024, Gants de protection contre les produits chimiques dangereux et les micro-organismes — Partie
1: Terminologie et exigences de performance pour les risques chimiques
ISO 374-2:2019, Gants de protection contre les produits chimiques dangereux et les micro-organismes — Partie
2: Détermination de la résistance à la pénétration
ISO 374-5:2024, Gants de protection contre les produits chimiques dangereux et les micro-organismes — Partie
5: Terminologie et exigences de performance pour les risques par les micro-organismes
ISO 6529:2013, Vêtements de protection — Protection contre les produits chimiques — Détermination de la
résistance des matériaux utilisés pour la confection des vêtements de protection à la perméation par des liquides
et des gaz
ISO 7000:2019, Symboles graphiques utilisables sur le matériel — Symboles enregistrés
ISO 21171:2006, Gants à usage médical — Détermination de la poudre résiduelle en surface
ISO 21420:2020, Gants de protection — Exigences générales et méthodes d’essai
ISO 21420:2020+Amd 1:2022, Gants de protection — Exigences générales et méthodes d’essai — Amendement 1
EN 16523-1:2015+Amd 1:2018, Détermination de la résistance des matériaux à la perméation par des produits
chimiques — Partie 1: Perméation par des produits chimiques liquides potentiellement dangereux dans des
conditions de contact continu
ISO/FDIS 374-6:2025(fr)
3 Termes et définitions
Pour les besoins du présent document, les termes et les définitions de l'EN 16523-1+Amd 1:2018,
l’ISO 374-1:2024 et l'ISO 374-5:2024 ainsi que les termes et définitions suivants s'appliquent.
Pour les besoins du présent document, les termes et définitions suivants s'appliquent.
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en normalisation,
consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l'adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l'adresse https:// www .electropedia .org/
3.1
gants de protection pour les coiffeurs
gants pour protéger la peau du coiffeur lors de la manipulation de produits chimiques et de l'utilisation d'eau
pendant son travail (coloration, décoloration, frisage, lavage…)
3.2
matériau d'un gant de protection
tout matériau ou combinaison de matériaux utilisés dans un gant de protection dans le but d'isoler les m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.