Alpine ski/binding/boot (S-B-B) system -- Assembly, adjustment and inspection

This document specifies assembly, adjustment and inspection procedures for the binding mechanisms of skis, integrating, in a practical way, the requirements of those International Standards which are related to skis, bindings and boots. It is intended for all individuals and institutions concerned with those procedures, and especially for sports retailers. It is applicable to a ski-binding-boot system (S-B-B) for alpine skiing, of which at least one component is owned by the user. This document is applicable for complete and incomplete alpine ski-binding-boot systems which are owned by the user or rented for 15 days or more. NOTE ISO 13993 gives a method of measurement for equipment which is rented for less than 15 days.

Ensemble ski/fixation/chaussure (SFC) pour skis alpins -- Montage, réglage et contrôle

Le présent document spécifie des modes opératoires de montage, de réglage et de contrôle des mécanismes de fixation des skis, en intégrant de maničre pratique les exigences des Normes internationales relatives aux skis, aux fixations de ski et aux chaussures de ski. Il s'adresse ŕ tous les individus et organismes concernés par ces modes opératoires, et notamment aux détaillants d'articles de sport. Il est applicable ŕ l'ensemble ski-fixation-chaussure (SFC) des skis alpins, dont au moins un des composants appartient ŕ l'utilisateur. Le présent document est applicable aux ensembles ski-fixation-chaussure, complets ou incomplets, qui appartiennent ŕ l'utilisateur ou qui sont loués pendant au moins 15 jours, pour la pratique du ski alpin. NOTE L'ISO 13993 indique une méthode de mesure des équipements qui sont loués pendant moins de 15 jours.

Sistem smuči/vezi/čevlji (S-B-B) za alpsko smučanje - Sestavljanje, nastavitev in nadzor

Ta dokument določa postopke sestavljanja, nastavitev in nadzora za mehanizme zapenjanja pri smučeh, ki na praktičen način vključujejo zahteve mednarodnih standardov, ki so povezani s smučmi, vezmi in čevlji.
Namenjen je vsem posameznikom in institucijam, ki se ukvarjajo s temi postopki, še zlasti prodajalcem športne opreme.
Uporablja se za sistem smuči/vezi/čevlji (S-B-B) za alpsko smučanje, pri čemer je uporabnik lastnik vsaj ene komponente.
Ta dokument se uporablja za popolne in nepopolne sisteme smuči/vezi/čevlji (S-B-B) za alpsko smučanje, ki so v lasti uporabnika ali so najeti za 15 dni ali več.
OPOMBA ISO 13993 podaja metodo merjenja opreme, ki je najeta za manj kot 15 dni.

General Information

Status
Published
Publication Date
29-May-2018
Current Stage
6060 - International Standard published
Start Date
16-Mar-2018
Completion Date
30-May-2018

RELATIONS

Buy Standard

Standard
ISO 11088:2018 - Alpine ski/binding/boot (S-B-B) system -- Assembly, adjustment and inspection
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11088:2018
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ISO 11088:2018
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ISO 11088:2018 - Ensemble ski/fixation/chaussure (SFC) pour skis alpins -- Montage, réglage et contrôle
French language
15 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 11088
Sixth edition
2018-05
Alpine ski/binding/boot (S-B-B)
system — Assembly, adjustment and
inspection
Ensemble ski/fixation/chaussure (SFC) pour skis alpins — Montage,
réglage et contrôle
Reference number
ISO 11088:2018(E)
ISO 2018
---------------------- Page: 1 ----------------------
ISO 11088:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 11088:2018(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 3

5 Skier's parameters ............................................................................................................................................................................................. 3

5.1 General ........................................................................................................................................................................................................... 3

5.2 Weight method ........................................................................................................................................................................................ 3

6 Equipment parameters .................................................................................................................................................................................. 3

6.1 Choice of new equipment .............................................................................................................................................................. 3

6.2 Visual inspection and preparation of used equipment ........................................................................................ 3

6.3 Assembly ...................................................................................................................................................................................................... 4

6.4 Binding-to-boot fitting adjustments ..................................................................................................................................... 4

6.5 Initial indicator adjustment ......................................................................................................................................................... 4

6.6 Functional check (inspection of functions) .................................................................................................................... 4

6.7 Measurement of release moment ........................................................................................................................................... 4

6.8 Report ............................................................................................................................................................................................................. 5

Annex A (normative) Definition of skier type ............................................................................................................................................. 6

Annex B (normative) Method of setting ............................................................................................................................................................ 8

Annex C (normative) Flow chart ............................................................................................................................................................................10

Annex D (normative) Clean versus lubricated diagnostic test for boot/binding compatibility ..........12

Annex E (informative) Drill .........................................................................................................................................................................................13

Bibliography .............................................................................................................................................................................................................................14

© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 11088:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/iso/foreword .html.

This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities

and equipment, Subcommittee SC 4, Snowsports equipment.

This sixth edition cancels and replaces the fifth edition (ISO 11088:2015), which has been technically

revised. The main changes are:

— the content of the test report has been extended to include specifications of the ski, the binding and

the boot;

— accepted deviation for the adjustment has been aligned to other relevant standards;

— in Annex A, other figures and characters have been given as an informative option for the indication

of skier type;
— the tibia method has been removed from Figure C.1;
— release preference instead of skier types;
— normative references have been updated;
— a new Clause 4 has been added.
iv © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 11088:2018(E)
Introduction

International Standards exist for the components of the alpine ski/binding/boot (S-B-B) system, mainly

intended for the component manufacturers. An International Standard (ISO 8061) also exists for the

selection of release moments.

This document is intended primarily for retailers. However, its aim is to include, in one text, the different

phases of the choice of components, their assembly, adjustment and inspection in the form of practical

procedures, and to provide tolerances for inspection and adjustment.

The inspection procedures and tolerances described in this document apply to the condition of the

S-B-B system before it leaves the ski shop to judge the condition of the equipment once it is put into use

and for periodic verification of used equipment.
© ISO 2018 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 11088:2018(E)
Alpine ski/binding/boot (S-B-B) system — Assembly,
adjustment and inspection
1 Scope

This document specifies assembly, adjustment and inspection procedures for the binding mechanisms

of skis, integrating, in a practical way, the requirements of those International Standards which are

related to skis, bindings and boots.

It is intended for all individuals and institutions concerned with those procedures, and especially for

sports retailers.

It is applicable to a ski-binding-boot system (S-B-B) for alpine skiing, of which at least one component is

owned by the user.

This document is applicable for complete and incomplete alpine ski-binding-boot systems which are

owned by the user or rented for 15 days or more.

NOTE ISO 13993 gives a method of measurement for equipment which is rented for less than 15 days.

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 5355, Alpine ski-boots — Requirements and test methods
ISO 8061:2015, Alpine ski-bindings — Selection of release torque values

ISO 8364, Alpine skis and bindings — Binding mounting area — Requirements and test methods

ISO 9462, Alpine ski-bindings — Requirements and test methods

ISO 9523, Touring ski-boots for adults — Interface with touring ski-bindings — Requirements and test methods

ISO 11087, Alpine ski-bindings — Retention devices — Requirements and test methods

ISO 11110, Winter-sports equipment — Test devices for the setting of the functional unit ski/boot/

binding — Requirements and tests
ISO 13992, Alpine touring ski-bindings — Requirements and test methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at http: //www .electropedia .org/
— ISO Online browsing platform: available at https: //www .iso .org/obp
3.1
fitting adjustment

procedure required to obtain geometric compatibility and correct functioning of different components

© ISO 2018 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 11088:2018(E)
3.2
indicator setting
Z-mark
release indicator value marked on the binding in accordance with ISO 9462
3.3
skier type

release adjustment (3.7) criteria pertaining to the type of skiing to be undertaken, as assessed by the

skier in accordance with Table A.1 or Table A.2

Note 1 to entry: If the skier desires a setting outside the tolerances of this document, he or she can select such

a setting at his or her own discretion. Ski-binding manufacturers should provide guidelines to shops and skiers

regarding the recommended magnitude of such changes. Skiers should be clearly informed when these changes

result in release values above the upper limit or below the lower limit defined in ISO 8061.

3.4
initial indicator position

release indicator position of the binding corresponding with the instructions given in Annex B

3.5 Release moment (values) M and M
Z Y
3.5.1
selected individual release moment
reference moment
〈for a given skier〉 release moment determined in accordance with ISO 8061
3.5.2
measured release moment
〈for a given S-B-B system〉 value for which the binding releases
Note 1 to entry: It is expressed in newton metres.
Note 2 to entry: The procedure is given in 6.7.
3.6
accepted inspection tolerance

maximum difference between the measured release moment (3.5.2) and the selected individual release

moment (3.5.1), limited for M and M to the release moments stated in Table B.1 one line above/below

Z Y
the reference moments

Note 1 to entry: The theoretical limits for M with ±15 % or ±3 Nm (whichever is higher) and M with ±15 %

Z Y

or ±10 Nm (whichever is higher) are the base for Table B.1. Long experience shows that using the table values

avoids many errors and is easier to explain to customers.
3.7
release adjustment

procedure for making the measured M and M values coincide with the selected individual M and M

Z Y Z Y
values within the limits stated in Table B.1
3.8
trouble-shooting procedures
additional procedures recommended by the equipment manufacturer
3.9
accepted re-adjustment tolerance

maximum difference between the measured release moment (3.5.2) at the initial indicator position (3.4)

and the selected individual release moment (3.5.1), limited for M and M to the release moments stated

Z Y
in Table B.1 two lines above/below the reference moments

Note 1 to entry: The theoretical limits for M with ±30 % or ±6 Nm (whichever is higher) and M with ±30 %

Z Y

or ±20 Nm (whichever is higher) are the base for Table B.1. Long experience shows that using the table values

avoids many errors and is easier to explain to customers.
2 © ISO 2018 – All rights reserved
---------------------- Page: 7 ----------------------
ISO 11088:2018(E)
4 Principle
Follow the procedure shown in Annex C.
5 Skier's parameters
5.1 General

The individual release moment values are given in ISO 8061. The following procedure, using discrete

values, may be considered an acceptable approximation of the basic functions of ISO 8061.

5.2 Weight method
5.2.1 Determine the skier's parameters:
a) mass (weight);
b) height;
c) type (according to Annex A);
d) age;
e) sole length if necessary.
5.2.2 Using Table B.1, choose the
...

SLOVENSKI STANDARD
oSIST ISO 11088:2018
01-september-2018

6LVWHPVPXþLYH]LþHYOML 6%% ]DDOSVNRVPXþDQMH6HVWDYOMDQMHQDVWDYLWHYLQ

QDG]RU
Alpine ski/binding/boot (S-B-B) system -- Assembly, adjustment and inspection

Ensemble ski/fixation/chaussure (SFC) pour skis alpins -- Montage, réglage et contrôle

Ta slovenski standard je istoveten z: ISO 11088:2018
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
oSIST ISO 11088:2018 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST ISO 11088:2018
---------------------- Page: 2 ----------------------
oSIST ISO 11088:2018
INTERNATIONAL ISO
STANDARD 11088
Sixth edition
2018-05
Alpine ski/binding/boot (S-B-B)
system — Assembly, adjustment and
inspection
Ensemble ski/fixation/chaussure (SFC) pour skis alpins — Montage,
réglage et contrôle
Reference number
ISO 11088:2018(E)
ISO 2018
---------------------- Page: 3 ----------------------
oSIST ISO 11088:2018
ISO 11088:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST ISO 11088:2018
ISO 11088:2018(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 3

5 Skier's parameters ............................................................................................................................................................................................. 3

5.1 General ........................................................................................................................................................................................................... 3

5.2 Weight method ........................................................................................................................................................................................ 3

6 Equipment parameters .................................................................................................................................................................................. 3

6.1 Choice of new equipment .............................................................................................................................................................. 3

6.2 Visual inspection and preparation of used equipment ........................................................................................ 3

6.3 Assembly ...................................................................................................................................................................................................... 4

6.4 Binding-to-boot fitting adjustments ..................................................................................................................................... 4

6.5 Initial indicator adjustment ......................................................................................................................................................... 4

6.6 Functional check (inspection of functions) .................................................................................................................... 4

6.7 Measurement of release moment ........................................................................................................................................... 4

6.8 Report ............................................................................................................................................................................................................. 5

Annex A (normative) Definition of skier type ............................................................................................................................................. 6

Annex B (normative) Method of setting ............................................................................................................................................................ 8

Annex C (normative) Flow chart ............................................................................................................................................................................10

Annex D (normative) Clean versus lubricated diagnostic test for boot/binding compatibility ..........12

Annex E (informative) Drill .........................................................................................................................................................................................13

Bibliography .............................................................................................................................................................................................................................14

© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST ISO 11088:2018
ISO 11088:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso. org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/iso/foreword .html.

This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities

and equipment, Subcommittee SC 4, Snowsports equipment.

This sixth edition cancels and replaces the fifth edition (ISO 11088:2015), which has been technically

revised. The main changes are:

— the content of the test report has been extended to include specifications of the ski, the binding and

the boot;

— accepted deviation for the adjustment has been aligned to other relevant standards;

— in Annex A, other figures and characters have been given as an informative option for the indication

of skier type;
— the tibia method has been removed from Figure C.1;
— release preference instead of skier types;
— normative references have been updated;
— a new Clause 4 has been added.
iv © ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST ISO 11088:2018
ISO 11088:2018(E)
Introduction

International Standards exist for the components of the alpine ski/binding/boot (S-B-B) system, mainly

intended for the component manufacturers. An International Standard (ISO 8061) also exists for the

selection of release moments.

This document is intended primarily for retailers. However, its aim is to include, in one text, the different

phases of the choice of components, their assembly, adjustment and inspection in the form of practical

procedures, and to provide tolerances for inspection and adjustment.

The inspection procedures and tolerances described in this document apply to the condition of the

S-B-B system before it leaves the ski shop to judge the condition of the equipment once it is put into use

and for periodic verification of used equipment.
© ISO 2018 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST ISO 11088:2018
---------------------- Page: 8 ----------------------
oSIST ISO 11088:2018
INTERNATIONAL STANDARD ISO 11088:2018(E)
Alpine ski/binding/boot (S-B-B) system — Assembly,
adjustment and inspection
1 Scope

This document specifies assembly, adjustment and inspection procedures for the binding mechanisms

of skis, integrating, in a practical way, the requirements of those International Standards which are

related to skis, bindings and boots.

It is intended for all individuals and institutions concerned with those procedures, and especially for

sports retailers.

It is applicable to a ski-binding-boot system (S-B-B) for alpine skiing, of which at least one component is

owned by the user.

This document is applicable for complete and incomplete alpine ski-binding-boot systems which are

owned by the user or rented for 15 days or more.

NOTE ISO 13993 gives a method of measurement for equipment which is rented for less than 15 days.

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 5355, Alpine ski-boots — Requirements and test methods
ISO 8061:2015, Alpine ski-bindings — Selection of release torque values

ISO 8364, Alpine skis and bindings — Binding mounting area — Requirements and test methods

ISO 9462, Alpine ski-bindings — Requirements and test methods

ISO 9523, Touring ski-boots for adults — Interface with touring ski-bindings — Requirements and test methods

ISO 11087, Alpine ski-bindings — Retention devices — Requirements and test methods

ISO 11110, Winter-sports equipment — Test devices for the setting of the functional unit ski/boot/

binding — Requirements and tests
ISO 13992, Alpine touring ski-bindings — Requirements and test methods
3 Terms a nd definiti ons
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at http:/ /www .electropedia .org/
— ISO Online browsing platform: available at https:/ /www. iso .org/obp
3.1
f it t i n g adju s t ment

procedure required to obtain geometric compatibility and correct functioning of different components

© ISO 2018 – All rights reserved 1
---------------------- Page: 9 ----------------------
oSIST ISO 11088:2018
ISO 11088:2018(E)
3.2
indicator setting
Z-mark
release indicator value marked on the binding in accordance with ISO 9462
3.3
skier type

release adjustment (3.7) criteria pertaining to the type of skiing to be undertaken, as assessed by the

skier in accordance with Table A.1 or Table A.2

Note 1 to entry: If the skier desires a setting outside the tolerances of this document, he or she can select such

a setting at his or her own discretion. Ski-binding manufacturers should provide guidelines to shops and skiers

regarding the recommended magnitude of such changes. Skiers should be clearly informed when these changes

result in release values above the upper limit or below the lower limit defined in ISO 8061.

3.4
initial indicator position

release indicator position of the binding corresponding with the instructions given in Annex B

3.5 Release moment (values) M and M
Z Y
3.5.1
selected individual release moment
reference moment
〈for a given skier〉 release moment determined in accordance with ISO 8061
3.5.2
measured release moment
〈for a given S-B-B system〉 value for which the binding releases
Note 1 to entry: It is expressed in newton metres.
Note 2 to entry: The procedure is given in 6.7.
3.6
accepted inspection tolerance

maximum difference between the measured release moment (3.5.2) and the selected individual release

moment (3.5.1), limited for M and M to the release moments stated in Table B.1 one line above/below

Z Y
the reference moments

Note 1 to entry: The theoretical limits for M with ±15 % or ±3 Nm (whichever is higher) and M with ±15 %

Z Y

or ±10 Nm (whichever is higher) are the base for Table B.1. Long experience shows that using the table values

avoids many errors and is easier to explain to customers.
3.7
release adjustment

procedure for making the measured M and M values coincide with the selected individual M and M

Z Y Z Y
values within the limits stated in Table B.1
3.8
trouble-shooting procedures
additional procedures recommended by the equipment manufacturer
3.9
accepted re-adjustment tolerance

maximum difference between the measured release moment (3.5.2) at the initial indicator position (3.4)

and the selected individual release moment (3.5.1), limited for M and M to the release moments stated

Z Y
in Table B.1 two lines above/below the reference moments

Note 1 to entry: The theoretical limits for M with ±30 % or ±6 Nm (whichever is higher) and M with ±30 %

Z Y

or ±20 Nm (whichever is higher) are the base for Table B.1. Long experience shows that using the table values

avoids many errors and is easier to explain to customers.
2 © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
oSIST ISO 11088:2018
ISO 11088:2018(E)
4 Principle
Follow the procedu
...

SLOVENSKI STANDARD
SIST ISO 11088:2018
01-oktober-2018
1DGRPHãþD
SIST ISO 11088:2011

6LVWHPVPXþLYH]LþHYOML 6%% ]DDOSVNRVPXþDQMH6HVWDYOMDQMHQDVWDYLWHYLQ

QDG]RU
Alpine ski/binding/boot (S-B-B) system -- Assembly, adjustment and inspection

Ensemble ski/fixation/chaussure (SFC) pour skis alpins -- Montage, réglage et contrôle

Ta slovenski standard je istoveten z: ISO 11088:2018
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
SIST ISO 11088:2018 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 11088:2018
---------------------- Page: 2 ----------------------
SIST ISO 11088:2018
INTERNATIONAL ISO
STANDARD 11088
Sixth edition
2018-05
Alpine ski/binding/boot (S-B-B)
system — Assembly, adjustment and
inspection
Ensemble ski/fixation/chaussure (SFC) pour skis alpins — Montage,
réglage et contrôle
Reference number
ISO 11088:2018(E)
ISO 2018
---------------------- Page: 3 ----------------------
SIST ISO 11088:2018
ISO 11088:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 11088:2018
ISO 11088:2018(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 3

5 Skier's parameters ............................................................................................................................................................................................. 3

5.1 General ........................................................................................................................................................................................................... 3

5.2 Weight method ........................................................................................................................................................................................ 3

6 Equipment parameters .................................................................................................................................................................................. 3

6.1 Choice of new equipment .............................................................................................................................................................. 3

6.2 Visual inspection and preparation of used equipment ........................................................................................ 3

6.3 Assembly ...................................................................................................................................................................................................... 4

6.4 Binding-to-boot fitting adjustments ..................................................................................................................................... 4

6.5 Initial indicator adjustment ......................................................................................................................................................... 4

6.6 Functional check (inspection of functions) .................................................................................................................... 4

6.7 Measurement of release moment ........................................................................................................................................... 4

6.8 Report ............................................................................................................................................................................................................. 5

Annex A (normative) Definition of skier type ............................................................................................................................................. 6

Annex B (normative) Method of setting ............................................................................................................................................................ 8

Annex C (normative) Flow chart ............................................................................................................................................................................10

Annex D (normative) Clean versus lubricated diagnostic test for boot/binding compatibility ..........12

Annex E (informative) Drill .........................................................................................................................................................................................13

Bibliography .............................................................................................................................................................................................................................14

© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 11088:2018
ISO 11088:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/iso/foreword .html.

This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities

and equipment, Subcommittee SC 4, Snowsports equipment.

This sixth edition cancels and replaces the fifth edition (ISO 11088:2015), which has been technically

revised. The main changes are:

— the content of the test report has been extended to include specifications of the ski, the binding and

the boot;

— accepted deviation for the adjustment has been aligned to other relevant standards;

— in Annex A, other figures and characters have been given as an informative option for the indication

of skier type;
— the tibia method has been removed from Figure C.1;
— release preference instead of skier types;
— normative references have been updated;
— a new Clause 4 has been added.
iv © ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 11088:2018
ISO 11088:2018(E)
Introduction

International Standards exist for the components of the alpine ski/binding/boot (S-B-B) system, mainly

intended for the component manufacturers. An International Standard (ISO 8061) also exists for the

selection of release moments.

This document is intended primarily for retailers. However, its aim is to include, in one text, the different

phases of the choice of components, their assembly, adjustment and inspection in the form of practical

procedures, and to provide tolerances for inspection and adjustment.

The inspection procedures and tolerances described in this document apply to the condition of the

S-B-B system before it leaves the ski shop to judge the condition of the equipment once it is put into use

and for periodic verification of used equipment.
© ISO 2018 – All rights reserved v
---------------------- Page: 7 ----------------------
SIST ISO 11088:2018
---------------------- Page: 8 ----------------------
SIST ISO 11088:2018
INTERNATIONAL STANDARD ISO 11088:2018(E)
Alpine ski/binding/boot (S-B-B) system — Assembly,
adjustment and inspection
1 Scope

This document specifies assembly, adjustment and inspection procedures for the binding mechanisms

of skis, integrating, in a practical way, the requirements of those International Standards which are

related to skis, bindings and boots.

It is intended for all individuals and institutions concerned with those procedures, and especially for

sports retailers.

It is applicable to a ski-binding-boot system (S-B-B) for alpine skiing, of which at least one component is

owned by the user.

This document is applicable for complete and incomplete alpine ski-binding-boot systems which are

owned by the user or rented for 15 days or more.

NOTE ISO 13993 gives a method of measurement for equipment which is rented for less than 15 days.

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 5355, Alpine ski-boots — Requirements and test methods
ISO 8061:2015, Alpine ski-bindings — Selection of release torque values

ISO 8364, Alpine skis and bindings — Binding mounting area — Requirements and test methods

ISO 9462, Alpine ski-bindings — Requirements and test methods

ISO 9523, Touring ski-boots for adults — Interface with touring ski-bindings — Requirements and test methods

ISO 11087, Alpine ski-bindings — Retention devices — Requirements and test methods

ISO 11110, Winter-sports equipment — Test devices for the setting of the functional unit ski/boot/

binding — Requirements and tests
ISO 13992, Alpine touring ski-bindings — Requirements and test methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at http: //www .electropedia .org/
— ISO Online browsing platform: available at https: //www .iso .org/obp
3.1
fitting adjustment

procedure required to obtain geometric compatibility and correct functioning of different components

© ISO 2018 – All rights reserved 1
---------------------- Page: 9 ----------------------
SIST ISO 11088:2018
ISO 11088:2018(E)
3.2
indicator setting
Z-mark
release indicator value marked on the binding in accordance with ISO 9462
3.3
skier type

release adjustment (3.7) criteria pertaining to the type of skiing to be undertaken, as assessed by the

skier in accordance with Table A.1 or Table A.2

Note 1 to entry: If the skier desires a setting outside the tolerances of this document, he or she can select such

a setting at his or her own discretion. Ski-binding manufacturers should provide guidelines to shops and skiers

regarding the recommended magnitude of such changes. Skiers should be clearly informed when these changes

result in release values above the upper limit or below the lower limit defined in ISO 8061.

3.4
initial indicator position

release indicator position of the binding corresponding with the instructions given in Annex B

3.5 Release moment (values) M and M
Z Y
3.5.1
selected individual release moment
reference moment
〈for a given skier〉 release moment determined in accordance with ISO 8061
3.5.2
measured release moment
〈for a given S-B-B system〉 value for which the binding releases
Note 1 to entry: It is expressed in newton metres.
Note 2 to entry: The procedure is given in 6.7.
3.6
accepted inspection tolerance

maximum difference between the measured release moment (3.5.2) and the selected individual release

moment (3.5.1), limited for M and M to the release moments stated in Table B.1 one line above/below

Z Y
the reference moments

Note 1 to entry: The theoretical limits for M with ±15 % or ±3 Nm (whichever is higher) and M with ±15 %

Z Y

or ±10 Nm (whichever is higher) are the base for Table B.1. Long experience shows that using the table values

avoids many errors and is easier to explain to customers.
3.7
release adjustment

procedure for making the measured M and M values coincide with the selected individual M and M

Z Y Z Y
values within the limits stated in Table B.1
3.8
trouble-shooting procedures
additional procedures recommended by the equipment manufacturer
3.9
accepted re-adjustment tolerance

maximum difference between the measured release moment (3.5.2) at the initial indicator position (3.4)

and the selected individual release moment (3.5.1), limited for M and M to the release moments stated

Z Y
in Table B.1 two lines above/below the reference moments

Note 1 to entry: The theoretical limits for M with ±30 % or ±6 Nm (whichever is higher) and M with ±30 %

Z Y

or ±20 Nm (whichever is higher) are the base for Table B.1. Long experience shows that using the table values

avoids many errors and is easier to explain to customers.
2 © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST ISO 11088:2018
ISO 11088:2018(E)
4 Principle
Follow th
...

NORME ISO
INTERNATIONALE 11088
Sixième édition
2018-05
Ensemble ski/fixation/chaussure
(SFC) pour skis alpins — Montage,
réglage et contrôle
Alpine ski/binding/boot (S-B-B) system — Assembly, adjustment and
inspection
Numéro de référence
ISO 11088:2018(F)
ISO 2018
---------------------- Page: 1 ----------------------
ISO 11088:2018(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018

Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette

publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,

y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut

être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.

ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 11088:2018(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Domaine d'application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Termes et définitions ....................................................................................................................................................................................... 1

4 Principe .......................................................................................................................................................................................................................... 3

5 Paramètres relatifs au skieur.................................................................................................................................................................. 3

5.1 Généralités .................................................................................................................................................................................................. 3

5.2 Méthode du poids ................................................................................................................................................................................. 3

6 Paramètres relatifs à l’équipement .................................................................................................................................................. 3

6.1 Choix d’un nouvel équipement ......... ......................................................................................................................................... 3

6.2 Contrôle visuel et préparation d’un équipement déjà utilisé ......................................................................... 4

6.3 Montage ......................................................................................................................................................................................................... 4

6.4 Réglage de la fixation à la chaussure .................................................................................................................................... 4

6.5 Préréglage initial de l’indicateur ............................................................................................................................................. 4

6.6 Contrôle fonctionnel (contrôle des fonctions) ............................................................................................................. 4

6.7 Mesurage du couple de déclenchement ............................................................................................................................ 5

6.8 Rapport .......................................................................................................................................................................................................... 5

Annexe A (normative) Définition du type de skieur ............................................................................................................................ 7

Annexe B (normative) Méthode de réglage ................................................................................................................................................... 9

Annexe C (normative) Organigramme .............................................................................................................................................................11

Annexe D (normative) Essai de diagnostic de compatibilité chaussure/fixation à l’état

propre, puis avec lubrifiant ....................................................................................................................................................................13

Annexe E (informative) Foret ....................................................................................................................................................................................14

Bibliographie ...........................................................................................................................................................................................................................15

© ISO 2018 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 11088:2018(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes

nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est

en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.

L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents

critères d'approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www

.iso .org/directives).

L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de

brevets reçues par l'ISO (voir www .iso .org/brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion

de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir le lien suivant: www .iso .org/avant -propos.

Le présent document a été élaboré par le comité technique ISO/TC 83, Matériel et équipements de sports

et autres activités de loisirs, sous-comité SC 4, Équipements de sport de neige.

Cette sixième édition annule et remplace la cinquième édition (ISO 11088:2015), qui a fait l’objet d’une

révision technique. Les principales modifications sont les suivantes:

— extension du contenu du rapport d’essai aux caractéristiques du ski, de la fixation et de la chaussure;

— alignement sur les autres normes pertinentes de l’écart de réglage accepté;

— dans l’Annexe A, autres valeurs et caractéristiques données pour information pour caractériser le

type de skieur;
— retrait de la méthode de la largeur du tibia à la Figure C.1;
— préférence de réglage du déclenchement au lieu des types de skieurs;
— mise à jour des références normatives;
— ajout d’un nouvel Article 4.
iv © ISO 2018 – Tous droits réservés
---------------------- Page: 4 ----------------------
ISO 11088:2018(F)
Introduction

Il existe des Normes internationales pour les composants de l’ensemble ski/fixation/chaussure (SFC)

pour skis alpins, qui sont conçues principalement à l’usage des fabricants de composants. Il existe

également une Norme internationale (ISO 8061) concernant le choix des couples de déclenchement des

fixations.

Le présent document s’adresse avant tout aux détaillants. Son objectif est cependant de réunir dans un

seul texte les différentes phases du choix des composants, leur montage, leur réglage et leur contrôle,

sous forme de modes opératoires pratiques, et de fournir des tolérances pour le contrôle et le réglage.

Les modes opératoires de contrôle et les tolérances consignées dans le présent document s’appliquent à

l’état de l’ensemble SFC avant qu’il ne quitte le magasin de sport pour évaluer l’état de cet ensemble une

fois que celui-ci est en service et pour les vérifications périodiques des équipements utilisés.

© ISO 2018 – Tous droits réservés v
---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 11088:2018(F)
Ensemble ski/fixation/chaussure (SFC) pour skis alpins —
Montage, réglage et contrôle
1 Domaine d'application

Le présent document spécifie des modes opératoires de montage, de réglage et de contrôle des

mécanismes de fixation des skis, en intégrant de manière pratique les exigences des Normes

internationales relatives aux skis, aux fixations de ski et aux chaussures de ski.

Il s’adresse à tous les individus et organismes concernés par ces modes opératoires, et notamment aux

détaillants d’articles de sport.

Il est applicable à l’ensemble ski-fixation-chaussure (SFC) des skis alpins, dont au moins un des

composants appartient à l’utilisateur.

Le présent document est applicable aux ensembles ski-fixation-chaussure, complets ou incomplets, qui

appartiennent à l'utilisateur ou qui sont loués pendant au moins 15 jours, pour la pratique du ski alpin.

NOTE L’ISO 13993 indique une méthode de mesure des équipements qui sont loués pendant moins de

15 jours.
2 Références normatives

Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu, des

exigences du présent document. Pour les références datées, seule l’édition citée s’applique. Pour les

références non datées, la dernière édition du document de référence s’applique (y compris les éventuels

amendements).
ISO 5355, Chaussures de ski pour skis alpins — Exigences et méthodes d’essai

ISO 8061:2015, Fixations de skis alpins — Sélection des valeurs du couple de déclenchement

ISO 8364, Skis et fixations de skis alpins — Zone de montage de la fixation — Exigences de tenue et

méthodes d'essai
ISO 9462, Fixations de skis alpins — Exigences et méthodes d'essai

ISO 9523, Chaussures de ski de randonnée pour adultes — Zone de contact avec les fixations de skis de

randonnée — Exigences et méthodes d’essai

ISO 11087, Fixations de skis alpins — Dispositifs de retenue — Exigences et méthodes d'essai

ISO 11110, Matériel de sports d'hiver — Dispositifs d'essai pour le réglage de l'unité fonctionnelle ski/

chaussure/fixation — Exigences et essais

ISO 13992, Fixations pour le ski alpin de randonnée — Exigences et méthodes d'essai

3 Termes et définitions

Pour les besoins du présent document, les termes et définitions suivants s’appliquent.

L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en

normalisation, consultables aux adresses suivantes:
— IEC Electropedia: disponible à l’adresse http: //www .electropedia .org/
© ISO 2018 – Tous droits réservés 1
---------------------- Page: 6 ----------------------
ISO 11088:2018(F)

— ISO Online browsing platform: disponible à l’adresse https: //www .iso .org/obp

3.1
réglage

mode opératoire exigé pour assurer la compatibilité géométrique et un fonctionnement correct des

différents composants
3.2
réglage de l’indicateur
repère Z

valeur de l’indicateur de déclenchement marquée sur la fixation conformément à l’ISO 9462

3.3
type de skieur

critère de réglage du déclenchement (3.7) selon le type de ski pratiqué, évalué par le skieur lui-même

conformément au Tableau A.1 ou au Tableau A.2

Note 1 à l'article: Si un skieur désire un réglage en dehors des tolérances du présent document, il peut sélectionner

un tel réglage à son gré. Il convient que les fabricants de fixations de ski fournissent des lignes directrices aux

magasins et aux skieurs concernant l’amplitude recommandée pour de telles modifications. Il convient que les

skieurs soient clairement informés lorsque ces modifications entraînent des valeurs de déclenchement situées

au-dessus de la limite supérieure ou au-dessous de la limite inférieure définies dans l’ISO 8061.

3.4
position initiale de l’indicateur

position de l’indicateur de déclenchement de la fixation correspondant aux instructions données dans

l'Annexe B
3.5 Couples (valeurs) de déclenchement M et M
Z Y
3.5.1
couple de déclenchement individuel sélectionné
couple de référence

〈pour un skieur donné〉 couple de déclenchement déterminé conformément à l’ISO 8061

3.5.2
couple de déclenchement mesuré

〈pour un ensemble SFC donné〉 valeur à laquelle se produit le déclenchement de la fixation

Note 1 à l'article: Cette valeur s'exprime en newtons mètres.
Note 2 à l'article: Le mode opératoire est donné en 6.7.
3.6
tolérance au contrôle acceptée

différence maximale entre le couple de déclenchement mesuré (3.5.2) et le couple de déclenchement

individuel sélectionné (3.5.1), limitée pour M et M aux couples de déclenchement déclarés dans le

Z Y
Tableau B.1 une ligne au-dessus/au-dessous des couples de référence

Note 1 à l'article: Les valeurs théoriques de M à ± 15 % près ou ± 3 Nm près (selon la valeur la plus élevée des deux)

et de M à ± 15 % près ou ± 10 Nm près (selon la valeur la plus élevée des deux) constituent la base du Tableau B.1.

L'expérience montre d'une part, que l'utilisation des valeurs du tableau permet d'éviter de nombreuses erreurs et

d'autre part, que l’utilisation de ce tableau est plus simple à expliquer aux clients.

3.7
réglage du déclenchement

mode opératoire permettant de faire coïncider les valeurs mesurées de M et M avec les valeurs

Z Y

individuelles sélectionnées de M et M , dans les limites indiquées dans le Tableau B.1

Z Y
2 © ISO 2018 – Tous droits réservés
---------------------- Page: 7 ----------------------
ISO 11088:2018(F)
3.8
modes opératoires d’intervention en cas de défaut de fonctionnement
IDF
modes opératoires supplémentaires recommandés par le fabricant de l’équipement
3.9
tolérance au réajustement acceptée

différence maximale entre le couple de déclenchement mesuré (3.5.2) pour la position initiale de

l’indicateur (3.4) et le couple de déclenchement individuel sélectionné (3.5.1), limitée pour M et M aux

Z Y

couples de déclenchement déclarés dans le Tableau B.1 deux lignes au-dessus/au-dessous des couples

de référence

Note 1 à l'article: Les valeurs théoriques de M à ± 30 % près ou ±6 Nm près (selon la valeur la plus élevée des deux)

et de M à ± 30 % près ou ±20 Nm près (selon la valeur la plus élevée des deux) constituent la base du Tableau B.1.

L'expérience montre d'une part, que l'utilisation des valeurs du tableau permet d'éviter de nombreuses erreurs et

d'autre part, que l’utilisation de ce tableau est plus simple à expliquer aux clients

4 Principe
Suivre le mode opératoire indiqué dans l'Annexe C.
5 Paramètres relatifs au skieur
5.1 Généralités

Les valeurs individuelles du couple de déclenchement sont données dans l’ISO 8061. Le mode opératoire

suivant, utilisant des valeurs discrètes, peut être considéré comme une approximation acceptable des

fonctions de base de l’ISO 8061.
5.2 Méthode du poids
5.2.1 Déterminer les paramètres suivants, relatifs au skieur:
a) masse (poids);
b) taille;
c) type (conformément à l’Annexe A);
d) âge;
e) longueur de la semelle, si nécessaire.

5.2.2 À l’aide du Tableau B.1, sélectionner les valeurs individuelles de déclenchement M et M .

Z Y
6 Paramètres relatifs à l’équipement
6.1 Choix d’un nouvel équipement
Les composants doivent être conformes aux documents suivante:
a) ISO 8364 pour les skis;
b) ISO 5355 et ISO 9523 pour les chaussures;
c) ISO 9462 et ISO 13992 pour les fixations;
© ISO 2018 – Tous droits réservés 3
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.