ISO 10575:2012

Resilient floor coverings — Specification for rubber sheet floor coverings with backing

ISO 10575:2012 specifies the characteristics of rubber sheet floor coverings with backing. ISO 10575:2012 includes a classification system based on intensity of use, which shows where resilient floor coverings should provide satisfactory service.

Revêtements de sol résilients — Spécifications pour les revêtements de sol en caoutchouc avec dossier

General Information

• Status: Published
• Publication Date: 23-Jul-2012
• ICS: 97.150 - Floor coverings
• Technical Committee: ISO/TC 219 - Floor coverings
• Drafting Committee: ISO/TC 219/WG 2 - Resilient floor coverings
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 30-Oct-2023

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10575
First edition
2012-08-01
Resilient floor coverings —
Specification for rubber sheet floor
coverings with backing
Revêtements de sol résilients — Spécifications pour les revêtements de
sol en caoutchouc avec dossier
Reference number
ISO 10575:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 10575:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10575:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10575 was prepared by Technical Committee ISO/TC 219, Floor coverings.
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 10575:2012(E)
Resilient floor coverings — Specification for rubber sheet floor
coverings with backing
1 Scope
This International Standard specifies the characteristics of rubber sheet floor coverings with backing.
This International Standard includes a classification system based on intensity of use, which shows where
resilient floor coverings should provide satisfactory service.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 105-B02, Textiles ― Tests for colour fastness ― Part B02: Colour fastness to artificial light: Xenon arc
fading lamp test
ISO 4649:2010, Rubber, vulcanized or thermoplastic ― Determination of abrasion resistance using a rotating
cylindrical drum device
ISO 4918, Resilient, textile and laminate floor coverings ― Castor chair test
ISO 7619-1, Rubber, vulcanized or thermoplastic ― Determination of indentation hardness ― Part 1: Durometer
method (Shore hardness)
ISO 23999, Resilient floor coverings ― Determination of dimensional stability and curling after exposure to heat
ISO 24340, Resilient floor coverings ― Determination of thickness of layers
ISO 24341, Resilient and textile floor coverings ― Determination of length, width and straightness of sheet
ISO 24343-1, Resilient and laminate floor coverings ― Determination of indentation and residual indentation ―
Part 1: Residual indentation
ISO 24344, Resilient floor coverings ― Determination of flexibility and deflection
ISO 24346, Resilient floor coverings ― Determination of overall thickness
ASTM D883, Standard Terminology Relating to Plastics
ASTM D1566, Standard Terminology Relating to Rubber
ASTM D3389, Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)
ASTM F1515, Standard Test Method for Measuring Light Stability of Resilient Flooring by Colour Change
EN 431, Resilient floor coverings ― Determination of peel resistance
EN 663, Resilient floor coverings ― Determination of conventional pattern depths
© ISO 2012 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 10575:2012(E)
3 Terms and definitions
3.1
rubber material
polymeric binder in the rubber sheet floor covering with backing satisfying the definition of rubber in ASTM D1566,
and having been vulcanized such that it became thermoset as defined in ASTM
...