SIST EN 50288-3-2:2013

Multi-element metallic cables used in analogue and digital communication and control - Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz - Work area and patch cord cables

EN 50288-3-2 is a sectional specification for unscreened cables, characterised from 1 MHz up to 100 MHz, to be used as work area cables to connect a telecommunications outlet to the terminal equipment and for patch cord cables to establish connections on a patch panel as defined in EN 50173. Work area and data centre cables may also be used as patch cord cables in any distributor of a generic building wiring system to interconnect with equipment or to cross-connect between cabling systems. This sectional specification contains the electrical, mechanical, transmission and environmental performance characteristics of the cables, when tested in accordance with the referenced test methods. This sectional specification is to be read in conjunction with EN 50288-1 which contains the essential provisions for its application. The cables covered in this sectional specification are intended to operate with voltages and currents normally encountered in communication systems. These cables are not intended to be used in conjunction with low impedance sources, for example, the electric power supplies of public utility mains.

Mehradrige metallische Daten- und Kontrollkabel für analoge und digitale Übertragung - Teil 3-2: Rahmenspezifikation für ungeschirmte Kabel bis 100 MHz - Geräteanschlusskabel und Schaltkabel

Câbles métalliques à éléments multiples utilisés pour les transmissions et les commandes analogiques et numériques - Partie 3-2: Spécification intermédiaire pour les câbles non blindés pour applications jusqu'à 100 MHz - Câbles de zone de travail et de brassage

Večelementni kovinski kabli za analogne in digitalne komunikacije in krmiljenje - 3-2. del: Področna specifikacija za nezaslonjene kable z lastnostmi do 100 MHz - Kabli za delovna območja in povezovalne vrvice

Standard EN 50288-3-2 je področna specifikacija za nezaslonjene kable, ki se lahko uporabljajo za pasovne širine od 1 MHz do 100 MHz kot kabli na delovnem območju za povezavo telekomunikacijske vtičnice s terminalsko opremo, ter za povezovalne vrvice za vzpostavljanje povezav na povezovalni plošči, kot je določeno v EN 50173. Kabli delovnega območja in podatkovnega centra se lahko uporabljajo tudi kot povezovalne vrvice v katerem koli razdelilniku generičnega stavbnega sistema ožičenja za povezavo z opremo ali navzkrižno povezavo med kabelskimi sistemi. Ta področna specifikacija vsebuje električne, mehanske, prenosne in okoljske karakteristike delovanja kablov pri preskušanju v skladu z navedenimi preskusnimi metodami. Ta področna specifikacija se uporablja skupaj s standardom EN 50288-1, ki vsebuje bistvene določbe za njeno uporabo. Kabli, zajeti v tej področni specifikaciji, so namenjeni za delovanje pri napetostih in tokovih, ki so običajni v komunikacijskih sistemih. Ti kabli niso namenjeni za uporabo z viri z nizko impedanco, na primer z električnim napajanjem javnih omrežij.

General Information

• Status: Published
• Public Enquiry End Date: 28-Mar-2012
• Publication Date: 10-Sep-2013
• ICS: 33.120.20 - Wires and symmetrical cables
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 29-Aug-2013
• Due Date: 03-Nov-2013
• Completion Date: 11-Sep-2013
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Mandate: M/212 - ICT - metallic and optical cables and cabling systems
• Ref Project: EN 50288-3-2:2013 - Multi-element metallic cables used in analogue and digital communication and control - Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz - Work area and patch cord cables

Relations

• Revised: SIST EN 50288-3-2:2004 - Multi-element metallic cables used in analogue and digital communication and control -- Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz - Work area and patch cord cables
• Effective Date: 06-May-2014
• Replaces: SIST EN 50288-3-2:2004 - Multi-element metallic cables used in analogue and digital communication and control -- Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz - Work area and patch cord cables
• Effective Date: 28-Jan-2023

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mehradrige metallische Daten- und Kontrollkabel für analoge und digitale Übertragung - Teil 3-2: Rahmenspezifikation für ungeschirmte Kabel bis 100 MHz - Geräteanschlusskabel und SchaltkabelCâbles métalliques à éléments multiples utilisés pour les transmissions et les commandes analogiques et numériques - Partie 3-2: Spécification intermédiaire pour les câbles non blindés pour applications jusqu'à 100 MHz - Câbles de zone de travail et de brassageMulti-element metallic cables used in analogue and digital communication and control - Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz - Work area and patch cord cables33.120.20Wires and symmetrical cablesICS:Ta slovenski standard je istoveten z:EN 50288-3-2:2013SIST EN 50288-3-2:2013en01-oktober-2013SIST EN 50288-3-2:2013SLOVENSKI
STANDARD



SIST EN 50288-3-2:2013



EUROPEAN STANDARD EN 50288-3-2 NORME EUROPÉENNE
EUROPÄISCHE NORM May 2013
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50288-3-2:2013 E
ICS 33.120.20 Supersedes EN 50288-3-2:2003
English version
Multi-element metallic cables used in analogue and digital communication and control -
Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz -
Work area and patch cord cables
Câbles métalliques à éléments multiples utilisés pour les transmissions et les commandes analogiques et numériques -
Partie 3-2: Spécification intermédiaire pour les câbles non blindés pour applications jusqu'à 100 MHz -
Câbles de zone de travail et de brassage
Mehradrige metallische Daten- und Kontrollkabel für analoge und digitale Übertragung -
Teil 3-2: Rahmenspezifikation für ungeschirmte Kabel bis 100 MHz -
Geräteanschlusskabel und Schaltkabel
This European Standard was approved by CENELEC on 2013-03-18. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 50288-3-2:2013



EN 50288-3-2:2013 - 2 -
Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms, definitions, symbols and abbreviations . 4 3.1 Terms and definitions . 4 3.2 Symbols and abbreviations . 4 4 Cable construction . 5 4.1 Conductor . 5 4.2 Insulation . 5 4.3 Cabling elements . 5 4.4 Identification of cabling elements . 5 4.5 Screening of cabling elements . 5 4.6 Cable make-up . 5 4.7 Filling compound . 5 4.8 Interstitial fillers . 5 4.9 Screening of the cable core . 5 4.10 Moisture barriers . 5 4.11 Wrapping layers . 5 4.12 Sheath . 6 5 Tests and requirements for completed cables . 6 5.1 Electrical tests . 6 5.2 Mechanical tests . 9 5.3 Environmental tests . 10 5.4 Fire performance tests . 10 Annex A (informative)
Maximum voltage, current and temperature rating for cables used for POE applications . 11 Annex B
(informative)
Blank Detail Specification . 12
SIST EN 50288-3-2:2013



- 3 - EN 50288-3-2:2013
Foreword This document EN 50288-3-2:2013 has been prepared by CLC/SC 46XC "Multicore, Multipair and Quad Data communication cables," of CLC/TC 46X, "Communication cables". The following dates are fixed: • latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-03-18 • latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2016-03-18 This document supersedes EN 50288-3-2:2003. EN 50288-3-2:2013 includes the following significant technical changes with respect to EN 50288-3-2:2003: − the addition of the Blank Detail Specification Annex; − a number minor corrections and updating of references; − the re-classification of ‘ELFEXT’ to ‘ACR-F’. This Part 3-2 is to be read in conjunction to EN 50288-1. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC). SIST EN 50288-3-2:2013



EN 50288-3-2:2013 - 4 -
1 Scope EN 50288-3-2 is a sectional specification for unscreened cables, characterised from 1 MHz up to 100 MHz, to be used as work area cables to connect a telecommunications outlet to the terminal equipment and for patch cord cables to establish connections on a patch panel as defined in EN 50173.
Work area and data centre cables may also be used as patch cord cables in any distributor of a generic building wiring system to interconnect with equipment or to cross-connect between cabling systems. This sectional specification contains the electrical, mechanical, transmission and environmental performance characteristics of the cables, when tested in accordance with the referenced test methods. This sectional specification is to be read in conjunction with EN 50288-1 which contains the essential provisions for its application. The cables covered in this sectional specification are intended to operate with voltages and currents normally encountered in communication systems. These cables are not intended to be used in conjunction with low impedance sources, for example, the electric power supplies of public utility mains. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 50173 Series Information technology - Generic cabling systems EN 50288-1
Multi-element metallic cables used in analogue and digital communication and control - Part 1: Generic specification EN 50289 Series Communication cables - Specifications for test methods EN 50290 Series Communication cables EN 60811 Series Electric and optical fibre cables - Test methods for non-metallic materials (IEC 60811 series) IEC 60189-2
Low-frequency cables and wires with PVC insulation and PVC sheath - Part 2: Cables in pairs, triples, quads and quintuples for inside installations 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this document the terms and definitions given in EN 50288-1 apply. 3.2 Symbols and abbreviations For the purposes of this document, the following abbreviations apply. EX Exogenous (derived or originating externally) POE Power Over Ethernet SIST EN 50288-3-2:2013



- 5 - EN 50288-3-2:2013
4 Cable construction 4.1 Conductor The conductor shall be solid or stranded copper and meet the requirements of
EN 50288-1, 4.1. The stranded conductor shall consist of seven wires each with a nominal diameter of ≥ 0,10 mm to ≤ 0,21 mm.
The conductor shall be plain or metal coated. The solid conductor nominal diameter shall be ≥ 0,4 mm to ≤ 0,8 mm.
NOTE
Constructions with ‘copper clad’ conductors do not meet the requirements 4.2 Insulation The insulation shall be of a suitable material according to the relevant part of EN 50290-2. 4.3 Cabling elements The cable element shall be a pair or a quad. 4.4 Identification of cabling elements Unless otherwise specified, the colour coding for identification is given in IEC 60189-2. The colours shall meet the requirements of EN 50288-1, 4.4. 4.5 Screening of cabling elements Not applicable. 4.6 Cable make-up The cable elements shall be laid up in concentric layer(s) or units to form the cable core. 4.7 Filling compound Not applicable. 4.8 Interstitial fillers Where fillers are used they shall meet the requirements of EN 50288-1, 4.8. 4.9 Screening of the cable core Not applicable. 4.10 Moisture barriers Not applicable. 4.11 Wrapping layers Where wrapping layers are used they shall be in accordance with EN 50288-1, 4.11. SIST EN 50288-3-2:2013



EN 50288-3-2:2013 - 6 -
4.12 Sheath The sheath shall be of a suitable material according to the relevant part of EN 50290-2. 5 Tests and requirements for completed cables The following tables give the tests to be applied, together with the respective limits, in order to demonstrate compliance with this specification. 5.1 Electrical tests 5.1.1 Low-frequency and d.c. electrical measurements Table 1 - Low-frequency and d.c. electrical measurements EN 50288-1 sub-clause
Parameter Requirement 5.1.1.1 Conductor loop resistance (D1)≤ 28,0 Ω/100 m
(D2)≤ 34,0 Ω/100 m
5.1.1.2 Conductor resistance unbalance ≤ 2,0 % 5.1.1.3 Dielectric strength conductor/conductor 1,0 kV d.c. or 0,7 kV a.c. for 1 min or 2,5 kV d.c. or 1,7 kV a.c. for 2 s 5.1.1.4 Insulation resistance ≥ 5 000 MΩ.km when teste
...