SIST EN 15015:2008
(Main)Plastics piping systems - Systems for hot and cold water not intended for human consumption - Performance characteristics for pipes, fittings and their joints
Plastics piping systems - Systems for hot and cold water not intended for human consumption - Performance characteristics for pipes, fittings and their joints
This European Standard specifies performance requirements for plastics pipes, fittings and their joints intended for hot and cold water installations for the conveyance of water and for heating systems with the exception of drinking water distribution for human consumption, and gives associated test methods for verification and evaluation of conformity with this European Standard.
NOTE Compliance of pipes, fittings and their joints with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC. However, until the operation of the envisaged European Acceptance Scheme for construction products in contact with water intended for human consumption and the revision of this standard, products conforming to this standard could be used for the transport of water intended for human consumption if they conform to the relevant national, regional or local regulatory provisions or recommendations applicable in the place of use.
Kunststoff-Rohrleitungssysteme - Rohrleitungssysteme für Warm- und Kaltwasser nicht für den menschlichen Gebrauch - Eigenschaften für die Gebrauchstauglichkeit von Rohren, Formstücken und deren Verbindungen
Diese Norm legt Leistungsanforderungen an Kunststoffrohre, -formstücke und ihre Verbindungen fest, die für die Warm- und Kaltwasserinstallation, für den Transport von Wasser und für Heizungssysteme, ausge-nommen die Verteilung von Trinkwasser vorgesehen sind und es gibt damit verbundene Prüfverfahren zur Verifizierung und Bewertung der Konformität mit dieser Norm an.
ANMERKUNG Für diese Anwendung werden "Scheiteldruckfestigkeit", "Biegefestigkeit in Längsrichtung", "Höchstlast für zulässige Verformung", "Widerstandsfähigkeit gegen hohe Temperaturen (bei Heizungsanlagen)", "Schlagzähigkeit", "Schweißbarkeit (bei Gasleitungsnetzen)", "Widerstandsfähigkeit gegen Durchdringung (bei Gasleitungsnetzen)", "elektrostatisches Verhalten (bei Brennstoffleitungsnetzen)", "Durchlässigkeit", "thermische Eigenschaften" und "Wärmeisolierung (hinsichtlich Energieeinsparung)" nicht behandelt.
Systemes de canalisations en plastique - Systemes pour eau chaude et froide non destinée a la consommation humaine - Caractéristiques de performance pour tubes, raccords et leurs assemblages
Le présent document spécifie les exigences de performance pour les tubes, raccords et leurs assemblages en plastique destinés aux installations pour le transport de l'eau chaude et froide et aux systemes de chauffage, a l'exception de la distribution de l'eau potable destinée a la consommation humaine, et indique les méthodes associées pour la vérification et l'évaluation de la conformité au présent document.
NOTE Pour cette application, la " résistance a l'écrasement ", la " résistance a la flexion longitudinale ", la " charge maximale pour la déformation admissible ", la " résistance a la température élevée (pour réseaux de chauffage) ", la " résistance au choc ", la " soudabilité (pour réseaux de gaz) ", la " résistance a la pénétration (pour réseaux de gaz) ", le " comportement électrostatique (pour réseaux de fioul) ", la " perméabilité ", les " propriétés thermiques " et l'" isolation thermique (associée a l'économie d'énergie) " ne sont pas traitées.
Cevni sistemi iz polimernih materialov - Sistemi za vročo in hladno nepitno vodo - Lastnosti cevi, fitingov in njihovih spojev
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme - Rohrleitungssysteme für Warm- und Kaltwasser nicht für den menschlichen Gebrauch - Eigenschaften für die Gebrauchstauglichkeit von Rohren, Formstücken und deren VerbindungenSystemes de canalisations en plastique - Systemes pour eau chaude et froide non destinée a la consommation humaine - Caractéristiques de performance pour tubes, raccords et leurs assemblagesPlastics piping systems - Systems for hot and cold water not intended for human consumption - Performance characteristics for pipes, fittings and their joints91.140.60Sistemi za oskrbo z vodoWater supply systems23.040.45Fitingi iz polimernih materialovPlastics fittings23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 15015:2007SIST EN 15015:2008en,fr01-januar-2008SIST EN 15015:2008SLOVENSKI
STANDARD
SIST EN 15015:2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15015October 2007ICS 23.040.01 English VersionPlastics piping systems - Systems for hot and cold water notintended for human consumption - Performance characteristicsfor pipes, fittings and their jointsSystèmes de canalisations en plastique - Systèmes poureau chaude et froide non destinée à la consommationhumaine - Caractéristiques de performance pour tubes,raccords et leurs assemblagesKunststoff-Rohrleitungssysteme - Rohrleitungssysteme fürWarm- und Kaltwasser nicht für den menschlichenGebrauch - Eigenschaften für die Gebrauchstauglichkeitvon Rohren, Formstücken und deren VerbindungenThis European Standard was approved by CEN on 23 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15015:2007: ESIST EN 15015:2008
EN 15015:2007 (E) 2 Contents page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms, definitions and symbols.6 4 Performance requirements.6 4.1 Reaction to fire.6 4.2 Internal pressure strength and resistance to high temperature.6 4.3 Dimensional tolerances.6 4.4 Tightness.7 4.5 Durability.7 4.6 Dangerous substances.7 5 Test methods.7 5.1 Reaction to fire.7 5.2 Determination of the design pressure.8 5.3 Dimensional tolerances.8 5.4 Tightness and durability.8 6 Evaluation of conformity.9 6.1 General.9 6.2 Initial type testing.10 6.3 Factory production control.11 6.4 One-off products and products produced in very low quantities.14 Annex A (normative)
Overall service (design) coefficients.15 A.1 General.15 A.2 Overall service (design) coefficients.15 Annex B (normative)
Product standards for hot and cold water installations inside buildings.16 Annex C (normative)
Standards for assessment of conformity for hot and
cold water installations inside buildings.18 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Directive (CPD).19 ZA.1 Scope and relevant characteristics.19 ZA.2 Procedure for attestation of conformity of plastics pipes and fittings.20 ZA.3 CE marking and labelling.24 Bibliography.28
SIST EN 15015:2008
EN 15015:2007 (E) 3 Foreword This document (EN 15015:2007) has been prepared by Technical Committee CEN/TC 155 "Plastics piping systems and ducting systems", the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by July 2009. This document has been prepared under the mandate M/131 “Pipes, tanks and ancillaries not in contact with water intended for human consumption” given to CEN by the European Commission and the European Free Trade Association and support essential requirements of EU Directives. For the relationship with EU Directives, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 15015:2008
EN 15015:2007 (E) 4 Introduction This European Standard contains only the performance characteristics needed to meet the essential requirements of EU Directive(s). It does not cover all characteristics of the products. These are specified in the standards listed in Annex A or in other appropriate product specifications. This harmonised European Standard is part of a family of cluster standards addressing plastics piping systems. The relationship is shown below.
Material independent
Specific solutions
For the harmonisation of plastics piping systems for hot and cold water (this European Standard) the following applies: For pipes and fittings
For valves Figure 1 SIST EN 15015:2008
EN 15015:2007 (E) 5 1 Scope This European Standard specifies performance requirements for plastics pipes, fittings and their joints intended for hot and cold water installations for the conveyance of water and for heating systems with the exception of drinking water distribution for human consumption, and gives associated test methods for verification and evaluation of conformity with this European Standard. NOTE
Compliance of pipes, fittings and their joints with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC. However, until the operation of the envisaged European Acceptance Scheme for construction products in contact with water intended for human consumption and the revision of this standard, products conforming to this standard could be used for the transport of water intended for human consumption if they conform to the relevant national, regional or local regulatory provisions or recommendations applicable in the place of use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1,
Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber EN 681-2,
Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers EN 12293,
Plastics piping systems — Thermoplastics pipes and fittings for hot and cold water — Test method for the resistance of mounted assemblies to temperature cycling EN 13501-1,
Fire classification of construction products and
building elements — Part 1: Classification using test data from reaction to fire tests EN 15012:2007, Plastics piping systems — Soil and waste discharge systems within the building structure — Performance characteristics for pipes, fittings and their joints EN ISO 1167-1,
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method (ISO 1167-1:2006) EN ISO 1167-2,
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) prEN ISO 1167-3,
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 3: Preparation of components (ISO/DIS 1167-3:2005) prEN ISO 1167-4,
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 4: Preparation of assemblies (ISO/DIS 1167-4:2006) EN ISO 3126,
Plastics piping systems — Plastics components — Determination of dimensions (ISO 3126:2005) EN ISO 9001:2000,
Quality management systems — Requirements (ISO 9001:2000) EN ISO 9080,
Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003) ISO 10508:2006,
Plastics piping systems for hot and cold water installations — Guidance for classification and design SIST EN 15015:2008
EN 15015:2007 (E) 6 ISO 17456,
Plastics piping systems — Multilayer pipes — Determination of the long-term strength BS 7291-1:2006,
Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings — Part 1: General requirements 3 Terms, definitions and symbols For the purposes of this document, the following terms, definitions and symbols apply. 3.1 nominal outside diameter dn specified outside diameter, in millimetres, assigned to a nominal size 3.2 design pressure PD highest pressure related to the circumstances for which the system has been designed and is intended to be used 4 Performance requirements 4.1 Reaction to fire Where subject to regulatory requirements, the product shall be tested and classified in accordance with 5.1. 4.2 Internal pressure strength and resistance to high temperature 4.2.1 Determination of design pressure PD When determined in accordance with 5.2, the internal pressure strength of the pipe and fitting shall be expressed as a design pressure PD of preferably 4 bar, 6 bar, 8 bar or 10 bar for a given class of application according to ISO 10508:2006 or class S according to BS 7291-1:2006 and declared by the manufacturer. 4.2.2 Verification of pressure strength The verification of the internal pressure strength of pipes and fittings shall be done in accordance with 5.2.3. 4.3 Dimensional tolerances The manufacturer shall declare the dimensional tolerances for the jointing of the components, either by means of: a) reference to a specific European Standard listed in Clause 2 or in Annex B, or b) in the absence of a European Standard, reference to a specific European product specification published by a recognized European organization, or c) in the absence of a) and b), reference to an International Standard, or d) in the absence of a), b) and c), by stating the values of his own specification and associated jointing method. Dimensions shall be measured in accordance with 5.3 and shall be within the declared tolerances. SIST EN 15015:2008
EN 15015:2007 (E) 7 4.4 Tightness For products in accordance with this standard leaktightness is required. Products covered by one of the standards listed in Annex B and having passed the type testing in accordance with the assessment of conformity part, are deemed to be leaktight (for standards with separate assessment of conformity parts see Annex C). Tests shall be carried out in accordance with 5.4. No leakage shall occur during the test period. Sealing rings (and gaskets) shall conform to EN 681-1or EN 681-2, as applicable. 4.5 Durability 4.5.1 Durability of pipes and fittings Pipes and fittings meeting the requirements of 4.2.1 shall be deemed to have a reasonable economic working life. NOTE 1 Current extrapolated tests indicate an economic working life time of plastics pipes and fittings covered by this European Standard to be in the region of 50 years. NOTE 2
The manufacturer of plastics pipes and fittings should give guidance on type of water treatment required and on aspects of applications such as oxygen permeation. 4.5.2 Long-term joint tightness The long-term joint tightness shall be tested in accordance with 5.4. No leakage shall occur during the test period. 4.5.3 Durability of elastomeric sealing joints Elastomeric sealing joints shall be deemed to be durable if the sealing element conforms to EN 681-1 or EN 681-2, as applicable. 4.6 Dangerous substances Attention is drawn to NOTE 1 and NOTE 2 in ZA.1. NOTE Mandate M/366 “Development of horizontal standardised assessment methods for harmonised approaches relating to dangerous substances under the Construction Products Directive (CPD)” as issued by the European Commission, will require specifications relating to dangerous substance once applicable to the covered products. 5 Test methods 5.1 Reaction to fire Classification shall be done in accordance with EN 13501-1. Mounting and fixing of pipes shall conform to Annex A of EN 15012:2007. NOTE In case where e.g. the given dimensions do not exist the choice of dimensions and the mounting and fixing should be agreed between the manufacturer and the notified body.
SIST EN 15015:2008
EN 15015:2007 (E) 8 5.2 Determination of the design pressure 5.2.1 Pipes where the design stress requirements are totally met by the base polymer The hydrostatic stress properties of the material shall be determined by testing in accordance with EN ISO 9080. Alternatively the hydrostatic stress properties may be determined by proving that the material conforms to the reference lines specified in the basic material standards. The test results from EN ISO 9080 or the reference lines from the basic material standards shall be used to calculate the design pressure by using an established method for calculating or determining the maximum allowable hoop stress applicable to pipes exposed to a range of internal pressures and/or temperatures during their expected lifetime with the service coefficients given in Annex A. One established method is described in EN ISO 13760 [1] taking into account an applicable class of service condition according to ISO 10508:2006 and service coefficients according to Annex A. Other national established methods may be used. NOTE
For advice see the basic material standards ISO 3213 [2] for PP, ISO 10146 [3] for PE-X, ISO 12230 [4] for PB,
ISO 24033 for PE-RT[5] and product standard EN ISO 15877-2 (see Annex B) for PVC-C. For material not covered by Annex A the manufacturer shall declare overall service coefficients with appropriate verification methods, e.g. by making reference to a European product specification [see 4.3 b)]. 5.2.2 Other pipe designs For multi-layer pipes the hydrostatic stress properties shall be determined according to ISO 17456. The result shall then be used as described in 5.2.1. The design pressure for designs where single dimensions are pressure rated at specific temperatures shall be calculated using the same procedure as in 5.2.1 but based on pressure instead of hydrostatic stress. 5.2.3 Internal pressure strength For checking the internal pressure strength testing shall be done in accordance with the appropriate parts of
EN ISO 1167 using hoop stresses relevant for the material, which were established when determining the design pressure PD in accordance with 5.2.1 or 5.2.2. 5.3 Dimensional tolerances The dimensions shall be measured in accordance with EN ISO 3126. 5.4 Tightness and durability The tightness of joints and the durability shall be tested in accordance with EN 12293 taking the design pressure PD and the declared classification of service conditions as in ISO 10508:2006, using parameters given in Table 1 or BS 7291-1:2006. SIST EN 15015:2008
EN 15015:2007 (E) 9 Table 1 — Test parameters for service classes (ISO 10508:2006)
Class 1 Class 2 Class 3 Class 4 Class 5 Highest test temperature, in °C 90 90 60 80 95 Lowest test temperature, in °C 20 20 20 20 20 Test pressure, in bar PD PD PD PD PD Number of cycles a 5 000 5 000 5 000 5 000 5 000 Number of test pieces One set of fittings in accordance with the configuration shown in EN 12293 Pre-stress force b b b b b a
Each cycle shall comprise of 1510+ min at the highest test temperature and 1510+ min at the lowest test temperature. b
The tensile stress to calculate the pre-stress force is calculated using the following equation:
σt = α × ∆T × E
where σt is the tensile stress, expressed in megapascals ( MPa); α is the coefficient of thermal expansion, expressed per Kelvin (1/K); ∆T is the temperature difference, expressed in Kelvins (K); E is the modulus of elasticity, expressed in megapascals (MPa).
6 Evaluation of conformity 6.1 General The conformity of pipes and fittings with the requirements of this standard and with the declared values (including classes) shall be demonstrated by: initial type testing; factory production control by the manufacturer, including product assessment. For the purposes of testing, pipes and fittings may be grouped into families, where it is considered that the results for one or more characteristics from any product within the family are representative for the same characteristics for all products within that family. NOTE 1 A product can be in more than one family for different characteristics. For type testing the following family groups applies. a) Pressure groups for pipes and fittings as given in Table 2. Table 2 — Pressure groups Pressure group Design pressure, PD bar 1 ≤ 6 2 > 6
b) Size groups for pipes and fittings as given in Table 3. SIST EN 15015:2008
EN 15015:2007 (E) 10 Table 3 — Size groups
Size group Range of nominal diameters, dn 1 dn ≤ 63 2 63 < dn ≤ 160
c) Fitting groups for fittings as given in Table 4. Table 4 — Fitting groups Fitting group Fittings 1 Elbows and tees 2 Reducers, couplers, end caps 3 All fittings except those included in group 1 and group 2.
6.2 Initial type testing 6.2.1 General Relevant type tests shall be carried out on new products and whenever there is a change in design, in material and/or in production method, other than routine in-process adjustment and extension of the product range (see Table 3). A change of supplier of a material or stabiliser does not lead to a change in performance if the chemical composition remains the same. Material modifications within certain limits are not considered as a change of material. Guidance for these limits can be found in the standards given in Annex C. For tests previously performed in accordance with the provisions of the standards listed in Annex B, or the recognized European specification, as applicable, (same product, same characteristic(s), same test method, same system of attestation etc.) the results may be taken into account. All characteristics given in Clause 4 shall be subject to calculation and/or initial type testing, except 4.5.3, where the characteristics of the components used have already been determined by the component manufacturer on the basis of conformity with other product standards. However this does not relieve the manufacturer of the piping system from the responsibility of ensuring that the system conforms to the requirements of this document. 6.2.2 Initial type test requirements The initial type testing of the characteristics according to Clause 4 shall be performed in accordance with the sampling procedure given under type tests (TT) of the applicable product specific standards for assessment of conformity as given in Annex C. If the standard does not contain one or the other of the characteristics, then testing as given in Table 5 shall apply. For products where no such standard exists Table 5 shall apply. SIST EN 15015:2008
EN 15015:2007 (E) 11 Table 5 — Type testing of pipes and fittings Testing relevant to a Essential characteristics Requirement clause of this document I M D E Acceptance Sampling procedure (minimum sampling) Reaction to fire 4.1 + b + b — — See classification in EN 13501-1 Once/material or formulation Internal pressure strength 4.2.2 + + — — Pass/fail One diameter / pressure group / size group / fitting group / material or formulation Dimensional tolerances 4.3 + + + + Pass/fail One diameter / pressure group/size group / fitting group / material or formulation Tightness 4.4 + + + + Pass/fail One diameter / pressure group / size group / jointing system / material or formulation Durability 4.5 + + + + By the classification of the long-term strength performance (see 4.2.1) and tightness
(see 4.4) Once/material or formulation
See 4.4 a I
is initial type test in case of new system;
M is change of material;
D is change of fitting design;
E is extension of the product range with new pressure group, size group or fitting group;
+ denotes testing relevant for the characteristic-occurrence-combination. b Only obligatory if subject to regulatory requirements applicable in the place of use.
Test reports shall be kept by the manufacturer for at least 10 years after discontinuation of the product. 6.3 Factory production control 6.3.1 General The manufacturer shall establish, document and maintain an FPC system to ensure that the products placed on the market conform to the stated performance characteristics. The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the use of the results to control raw and other incoming materials or components, equipment, the production process and the product. If the manufacturer has the component designed, manufactured, assembled, packed, processed and labelled by subcontracting, FPC of the original manufacturer may be taken into account. However, where subcontracting takes place, the manufacturer shall retain the overall control of the component and ensure that he receives all the information that is necessary to fulfil his responsibilities according to this European Standard. The manufacturer who subcontracts all of his activities may in no circumstances discharge himself of his responsibilities to a subcontractor. All the elements, requirements and provisions adopted by the manufacturer shall be documented in a systematic manner in the form of written policies and procedures. This production control system documentation shall ensure a common understanding of conformity evaluation and enable the achievement of the required component characteristics and the effective operation of the production control system to be checked. Factory production control therefore brings together operational techniques and all measures allowing maintenance and control of the conformity of the component with its technical specifications. Its implementation may be achieved by controls and tests on raw materials and constituents, processes, manufacturing equipment and finished components, including material properties in components, and by making use of the results thus obtained. SIST EN 15015:2008
EN 15015:2007 (E) 12 The results of inspections, tests or assessments requiring action shall be recorded, as shall any action taken. The action to be taken when control values or criteria are not met shall be recorded and retained for the period specified in the manufacturers FPC procedures. The specifications of all incoming raw materials and components shall be documented, and the inspection scheme for ensuring their conformity shall be established. Manufacturers operating a quality system, which conforms to or is no less stringent than the relevant requirements of EN ISO 9001 and which is made specific to products covered by this European Standard is deemed to satisfy the FPC requirements of this European Standard. 6.3.2 FPC requirements Manufacturers shall operate a factory production control (FPC) system. FPC shall consist of tests to be carried out at regular intervals by the manufacturer to evaluate the conformity of the products with the requirements of this European Standard. The FPC of the characteristics according to Clause 4 shall be performed in accordance with the sampling procedure given under batch release tests (BRT) or process verification tests (PVT) of the applicable product specific standards for assessment of conformity as given in Annex C. If the standard does not contain one or the other of the characteristics, then testing as given in Table 6 shall apply. For products where no such standard exists Table 6 applies. Table 6 — Factory production control of pipes and fittings Essential characteristics Requirement clause of this European Standard Test method Minimum sampling frequency/production line Acceptance Reaction to fire a 4.1 Identification of material or formulation Once/batch See classification in EN 13501-1 Internal pressure strength 4.2.2 EN ISO 1167-1 and EN ISO 1167-2, or prEN ISO 1167-3, or prEN ISO 1667-4 as appropriate Once/batch Pass/fail Dimensional tolerances 4.3 EN ISO 3126 or according the manufacturers quality plan Once/batch Pass/fail Tightness 4.4 Indirect testing: see dimensional tolerances Once/batch Pass/fail Durability 4.5 Indirect testing: see internal pressure strength, dimensional tolerances and material or formulationOnce/batch Pass/fail a Only obligatory if subject to regulatory requirements applicable in the place of use.
SIST EN 15015:2008
EN 15015:2007 (E) 13 6.3.3 FPC system requirements 6
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.