SIST EN ISO 14527-3:2000
(Main)Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14527-3:1999)
Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14527-3:1999)
This part of ISO 14527 specifies the requirements for the physical and chemical properties of urea-formaldehyde
and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) and compression- or
injection-moulded test specimens produced from them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to those moulding compounds which are of general technical and/or economic importance.
The properties which are used to characterize the moulding compounds, the test methods and the test conditions
are selected from those given in ISO 14527-2.
The moulding compounds are divided into types according to their composition and properties. The various types
are designated using the designation system defined in ISO 14527-1.
Kunststoffe - Rieselfähige Harnstoff-Formaldehyd und Harnstoff/Melamin-Formaldehyd-Formmassen (UF- und UF/MF-PMC) - Teil 3: Anforderungen an ausgewählte Formmassen (ISO 14527-3:1999)
In diesem Teil von ISO 14527 werden die Anforderungen an physikalische und chemische Eigenschaften von rieselfähigen Harnstoff-Formaldehyd- und Harnstoff/Melamin-Formaldehyd-Formmassen (UF- und UF/MF-PMC) und daraus formgepreßten oder spritzgegossenen Probekörpern festgelegt. Die Auswahl ist auf solche Formmassen begrenzt, deren Zusammensetzung und Eigenschaften sich deutlich unterscheiden. Außerdem ist die Auswahl auf die Formmassen begrenzt, die von allgemeinerer technischer und/oder wirtschaftlicher Bedeutung sind.
Plastiques - Poudres a mouler a base d'urée-formaldéhyde et d'urée/mélamine-formaldéhyde (UF- et UF/MF-PMC) - Partie 3: Exigences relatives a certaines poudres a mouler (ISO 14527-3:1999)
La présente partie de l'ISO 14527 spécifie les caractéristiques physiques et chimiques des poudres à mouler à
base d'urée-formaldéhyde et d'urée/mélamine-formaldéhyde (UF- et UF/MF-PMC) et des éprouvettes moulées par
injection ou par compression, produites à partir de ces poudres.
Elle se limite aux poudres à mouler dont la composition et les propriétés diffèrent de manière significative. En
outre, elle ne concerne que les poudres à mouler dont l'importance technique et/ou économique est assez
générale.
Les propriétés qui sont utilisées pour caractériser les poudres à mouler, ainsi que les méthodes et conditions
d'essai, sont choisies parmi celles indiquées dans l'ISO 14527-2.
Les poudres à mouler sont réparties en différents types selon leur composition et leurs propriétés. Ces divers types
sont désignés en utilisant le système de désignation défini dans l'ISO 14527-1.
Polimerni materiali - Sečnina-formaldehidne in sečnina/melamin-formaldehidne praškaste zmesi za oblikovanje (UF- in UF/MF- PMCs) - 3. del: Zahteve za izbrane zmesi za oblikovanje (ISO 14527-3:1999)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14527-3:2000
01-december-2000
3ROLPHUQLPDWHULDOL6HþQLQDIRUPDOGHKLGQHLQVHþQLQDPHODPLQIRUPDOGHKLGQH
SUDãNDVWH]PHVL]DREOLNRYDQMH 8)LQ8)0)30&V GHO =DKWHYH]DL]EUDQH
]PHVL]DREOLNRYDQMH ,62
Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding
compounds (UF- and UF/MF-PMCs) - Part 3: Requirements for selected moulding
compounds (ISO 14527-3:1999)
Kunststoffe - Rieselfähige Harnstoff-Formaldehyd und Harnstoff/Melamin-Formaldehyd-
Formmassen (UF- und UF/MF-PMC) - Teil 3: Anforderungen an ausgewählte
Formmassen (ISO 14527-3:1999)
Plastiques - Poudres a mouler a base d'urée-formaldéhyde et d'urée/mélamine-
formaldéhyde (UF- et UF/MF-PMC) - Partie 3: Exigences relatives a certaines poudres a
mouler (ISO 14527-3:1999)
Ta slovenski standard je istoveten z: EN ISO 14527-3:1999
ICS:
83.080.10 Duromeri Thermosetting materials
SIST EN ISO 14527-3:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14527-3:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 14527-3:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 14527-3:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 14527-3:2000
---------------------- Page: 5 ----------------------
SIST EN ISO 14527-3:2000
---------------------- Page: 6 ----------------------
SIST EN ISO 14527-3:2000
INTERNATIONAL ISO
STANDARD 14527-3
First edition
1999-11-15
Plastics — Urea-formaldehyde and
urea/melamine-formaldehyde powder
moulding compounds (UF- and
UF/MF-PMCs) —
Part 3:
Requirements for selected moulding
compounds
Plastiques — Poudres à mouler à base d'urée-formaldéhyde et
d'urée/mélamine-formaldéhyde (UF- et UF/MF-PMC) —
Partie 3: Exigences relatives à certaines poudres à mouler
Reference number
ISO 14527-3:1999(E)
�
©
ISO 1999
---------------------- Page: 7 ----------------------
SIST EN ISO 14527-3:2000
ISO 14527-3:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14527-3:2000
ISO 14527-3:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 14527 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14527-3 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
After a transition period of, at the most, four years, the three parts of ISO 14527 (see below), together with the
three parts of ISO 14528, will replace ISO 2112:1990, of which they constitute a technical revision.
ISO 14527 consists of the following parts, under the general title Plastics — Urea-formaldehyde and
urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs):
� Part 1: Designation system and basis for specifications
� Part 2: Preparation of test specimens and determination of properties
� Part 3: Requirements for selected moulding compounds
Annex A of this part of ISO 14527 is for information only.
© ISO 1999 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 14527-3:2000
---------------------- Page: 10 ----------------------
SIST EN ISO 14527-3:2000
INTERNATIONAL STANDARD ISO 14527-3:1999(E)
Plastics — Urea-formaldehyde and urea/melamine-formaldehyde
powder moulding compounds (UF- and UF/MF-PMCs) —
Part 3:
Requirements for selected moulding compounds
1 Scope
This part of ISO 14527 specifies the requirements for the physical and chemical properties of urea-formaldehyde
and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) and compression- or
injection-moulded test specimens
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.