ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 17: Specific conditions for Broadband Data Transmission Systems - Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU

The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of
measurements for Broadband Data Transmission System equipment, as detailed in annex B.
Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are
not included in the present document. Such technical specifications are found in the relevant product standards for the
effective use of the radio spectrum.
The present document specifies the applicable test conditions, performance assessment and performance criteria for
wideband data communication systems.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.

Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 17. del: Posebni pogoji za širokopasovne sisteme za prenos podatkov - Harmonizirani standard, ki zajema bistvene zahteve člena 3.1(b) direktive 2014/53/EU

Ta dokument skupaj s standardom ETSI EN 301 489-1 [1] določa tehnične karakteristike in merilne metode za širokopasovne sisteme za prenos podatkov, kot je opredeljeno v dodatku B.
Ta dokument ne vključuje tehničnih specifikacij v zvezi z antenskim vhodom in sevanjem iz vhoda na ohišju radijske opreme. Takšne tehnične specifikacije so navedene v ustreznih standardih za izdelek na področju učinkovite uporabe radijskega spektra.
Dokument določa veljavne preskusne pogoje, oceno zmogljivosti in merila zmogljivosti za širokopasovne podatkovne komunikacijske sisteme.
Če se ta dokument in standard ETSI EN 301 489-1 [1] razlikujeta (na primer glede posebnih pogojev, opredelitev, kratic), imajo prednost določbe tega dokumenta.
Okoljska razvrstitev ter zahteve glede sevanja in odpornosti iz tega dokumenta so navedene v standardu ETSI EN 301 489-1 [1], razen posebnih pogojev iz tega dokumenta.
Ta dokument zajema bistvene zahteve člena 3.1(b) direktive 2014/53/EU [i.1] pod pogoji iz dodatka A.

General Information

Status
Published
Public Enquiry End Date
30-Jun-2016
Publication Date
27-Feb-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Feb-2017
Due Date
21-Apr-2017
Completion Date
28-Feb-2017

Buy Standard

Standard
SIST EN 301 489-17 V3.1.1:2017
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 301 489-17 V3.1.1 (2017-02) - Part 17: Specific conditions for Broadband Data Transmission Systems; Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 489-17 V3.1.1 (2016-11) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 489-17 V3.1.0 (2016-04) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU
English language
18 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 301 489-17 V3.1.1:2017
01-april-2017

6WDQGDUGHOHNWURPDJQHWQH]GUXåOMLYRVWL (0& ]DUDGLMVNRRSUHPRLQVWRULWYH

GHO3RVHEQLSRJRML]DãLURNRSDVRYQHVLVWHPH]DSUHQRVSRGDWNRY+DUPRQL]LUDQL
VWDQGDUGNL]DMHPDELVWYHQH]DKWHYHþOHQD E GLUHNWLYH(8

ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part

17: Specific conditions for Broadband Data Transmission Systems - Harmonised
Standard covering the essential requirements of article 3.1(b) of the Directive
2014/53/EU
Ta slovenski standard je istoveten z: ETSI EN 301 489-17 V3.1.1 (2017-02)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 301 489-17 V3.1.1:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 301 489-17 V3.1.1:2017
---------------------- Page: 2 ----------------------
SIST EN 301 489-17 V3.1.1:2017
ETSI EN 301 489-17 V3.1.1 (2017-02)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 17: Specific conditions for
Broadband Data Transmission Systems;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 3 ----------------------
SIST EN 301 489-17 V3.1.1:2017
2 ETSI EN 301 489-17 V3.1.1 (2017-02)
Reference
REN/ERM-EMC-335
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 489-17 V3.1.1:2017
3 ETSI EN 301 489-17 V3.1.1 (2017-02)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definitions and abbreviations ................................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.0 General .......................................................................................................................................................... 8

4.2.1 Arrangements for test signals at the input of transmitters ............................................................................. 8

4.2.2 Arrangements for test signals at the output of transmitters ........................................................................... 9

4.2.3 Arrangements for test signals at the input of receivers ................................................................................. 9

4.2.4 Arrangements for test signals at the output of receivers ............................................................................... 9

4.2.5 Arrangements for testing transmitter and receiver together (as a system) .................................................... 9

4.2.6 Equipment with an external antenna connector ............................................................................................ 9

4.2.7 Equipment without an external antenna connector (integral antenna) .......................................................... 9

4.2.8 Equipment with more than one antenna ...................................................................................................... 10

4.3 Exclusion bands ................................................................................................................................................ 10

4.4 Narrow band responses on receivers or receivers which are part of transceivers ............................................. 10

4.5 Normal test modulation .................................................................................................................................... 10

5 Performance assessment ......................................................................................................................... 11

5.1 General ............................................................................................................................................................. 11

5.2 Arrangements for the assessment of host dependant equipment and plug-in cards .......................................... 11

5.2.0 Introduction................................................................................................................................................. 11

5.2.1 Alternative A: composite equipment .......................................................................................................... 11

5.2.2 Alternative B: use of a test jig or host ......................................................................................................... 11

5.3 Assessment procedures ..................................................................................................................................... 12

5.4 Ancillary equipment ......................................................................................................................................... 12

5.5 Equipment classification .................................................................................................................................. 12

6 Performance criteria ............................................................................................................................... 12

6.1 General performance criteria ............................................................................................................................ 12

6.2 Performance table ............................................................................................................................................. 13

6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) .............................................. 13

6.4 Performance criteria for Transient phenomena applied to Transmitters (TT) .................................................. 14

6.5 Performance criteria for Continuous phenomena applied to Receivers (CR) ................................................... 14

6.6 Performance criteria for Transient phenomena applied to Receivers (TR) ...................................................... 14

7 Applicability overview ........................................................................................................................... 14

7.1 Emission ........................................................................................................................................................... 14

7.1.1 General ........................................................................................................................................................ 14

7.1.2 Special conditions ....................................................................................................................................... 14

7.2 Immunity .......................................................................................................................................................... 14

7.2.1 General ........................................................................................................................................................ 14

7.2.2 Special conditions ....................................................................................................................................... 15

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 16

Annex B (informative): Examples of radio equipment in the scope of the present document ........ 18

ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 489-17 V3.1.1:2017
4 ETSI EN 301 489-17 V3.1.1 (2017-02)

B.1 Introduction ............................................................................................................................................ 18

B.2 Data transmission systems operating in the 2,4 GHz ISM band and using wide band modulation

techniques ............................................................................................................................................... 18

B.3 5 GHz high performance RLAN systems ............................................................................................... 18

B.4 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz ........................ 18

B.5 Broadband data transmitting/BWA Terminal Stations ........................................................................... 18

B.6 Multi-Gigabit Wireless Systems (MGWS) ............................................................................................ 18

Annex C (informative): Change History .............................................................................................. 19

History .............................................................................................................................................................. 20

ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 489-17 V3.1.1:2017
5 ETSI EN 301 489-17 V3.1.1 (2017-02)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.12] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated

EFTA regulations.

The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 30 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 7 ----------------------
SIST EN 301 489-17 V3.1.1:2017
6 ETSI EN 301 489-17 V3.1.1 (2017-02)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of

measurements for Broadband Data Transmission System equipment, as detailed in annex B.

Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are

not included in the present document. Such technical specifications are found in the relevant product standards for the

effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

wideband data communication systems.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] under the

conditions identified in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

http://docbox.etsi.org/Reference.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.1.1) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 301 489-17 V3.1.1:2017
7 ETSI EN 301 489-17 V3.1.1 (2017-02)

[i.3] ETSI EN 301 893: "Broadband Radio Access Networks (BRAN); 5 GHz high performance

RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE

Directive".

[i.4] ETSI EN 302 502: "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data

transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the

R&TTE Directive".

[i.5] ETSI EN 302 544-2: "Broadband Data Transmission Systems operating in the 2 500 MHz to

2 690 MHz frequency band; Part 2: TDD User Equipment Stations; Harmonized EN covering the

essential requirements of article 3.2 of the R&TTE Directive".

[i.6] ETSI EN 302 567: "WAS/RLAN systems; Multiple-Gigabit WAS/RLAN equipment operating in

the 60 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU".

[i.7] ETSI EN 302 623: "Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz

frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of

article 3.2 of the R&TTE Directive".

[i.8] ETSI EN 300 328: "Wideband transmission systems; Data transmission equipment operating in the

2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering

the essential requirements of article 3.2 of Directive 2014/53/EU".
[i.9] Void.

[i.10] ETSI EN 301 908-19: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 19: OFDMA TDD WMAN (Mobile

WiMAXTM) TDD User Equipment (UE)".

[i.11] ETSI EN 301 908-21: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile

WiMAX ) FDD User Equipment (UE)".

[i.12] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following

apply:

Equipment Under Test (EUT): equipment subject to the performance requirements of the present document

fixed station: equipment intended for use in a fixed location and fitted with one or more antennas

NOTE: The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.

hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person

NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna

socket(s) or integral antenna(s) or both.

host: any equipment which has complete user functionality when not connected to the radio equipment part and to

which the radio equipment part provides additional functionality and to which connection is necessary for the radio

equipment part to offer functionality
ETSI
---------------------- Page: 9 ----------------------
SIST EN 301 489-17 V3.1.1:2017
8 ETSI EN 301 489-17 V3.1.1 (2017-02)

plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host

systems, using their control functions and power supply

stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally

used on a stand-alone basis
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
ACK ACKnowledgement
ARQ Automatic Retransmission reQuest
BRAN Broadband Radio Access Networks
BWA Broadband Wireless Access
CR Continuous phenomena applied to Receivers
CT Continuous phenomena applied to Transmitters
DC Direct Current
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio Matters
EUT Equipment Under Test
ISM Industrial, Scientific and Medical
MGWS Multi-Gigabit Wireless Systems
MUS Maximum Usable Sensitivity
NACK Not ACKnowledgement
RF Radio Frequency
RLAN Radio Local Area Network
TR Transient phenomena applied to Receivers
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as

appropriate. Further product related test conditions for wideband data communications systems are specified in

clauses 4.2 to 4.5.

The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires

connection to a host equipment to function shall use the test configuration as defined by the manufacturer. In all cases

the EUT shall be exercised in a manner representative of normal intended use.
4.2 Arrangements for test signals
4.2.0 General
The provisions of ETSI EN 301 489-1 [1], clause 4.2 shall apply.
4.2.1 Arrangements for test signals at the input of transmitters

The provisions of ETSI EN 301 489-1 [1], clause 4.2.1 shall apply with the following modifications.

The wanted signals and/or controls required to establish a communications link shall be defined by the manufacturer.

The transmitter shall be operated at maximum rated power.
ETSI
---------------------- Page: 10 ----------------------
SIST EN 301 489-17 V3.1.1:2017
9 ETSI EN 301 489-17 V3.1.1 (2017-02)
4.2.2 Arrangements for test signals at the output of transmitters

The provisions of ETSI EN 301 489-1 [1], clause 4.2.2 shall apply with the following modifications.

The manufacturer may provide a suitable companion receiver that can be used to receive messages or to set up a

communication link.
4.2.3 Arrangements for test signals at the input of receivers

The provisions of ETSI EN 301 489-1 [1], clause 4.2.3 shall apply with the following modifications.

The wanted signals required to establish a communications link shall be defined by the manufacturer.

The level of the wanted signal at the input of the receiver shall be at least 30 dB above the declared Maximum Usable

Sensitivity (MUS).
4.2.4 Arrangements for test signals at the output of receivers

The measuring equipment for the output signal from the receiver under test shall be located outside the test

environment.

It shall be possible to assess the performance of the equipment by appropriately monitoring the receiver output.

If the receiver has an output connector or port providing the wanted output signal, then this port shall be used via a

cable, consistent with the standard cable used in normal operation, connected to the external measuring equipment

outside the test environment. The measuring equipment may be supplied by the manufacturer.

Precautions shall be taken to ensure that any effect on the test due to the coupling means is minimized.

The manufacturer may provide a suitable companion transmitter that can be used to transmit messages or to set up a

communication link.
4.2.5 Arrangements for testing transmitter and receiver together
(as a system)
The provisions of ETSI EN 301 489-1 [1], clause 4.2.5 shall apply.

The manufacturer may provide a suitable companion transceiver or transmitter and receiver that can be used to send and

receive messages or to set up a communication link.

Both the EUT and the companion equipment shall transmit the normal test modulation. Further, the output of the radio

equipment under test shall be monitored by the test system.
4.2.6 Equipment with an external antenna connector

If access to the antenna connector involves modification or dismantling of the EUT then this clause does not apply.

The EUT may be tested with its antenna removed.

In the case of testing with the antenna removed, the wanted RF input and output signals shall be delivered between the

EUT antenna connector and the measuring and/or test equipment by a shielded transmission line, such as a coaxial

cable. Adequate measures shall be taken to minimize the effect of common mode currents on the transmission line at

the point of entry to the EUT and at the measuring/test equipment.
4.2.7 Equipment without an external antenna connector (integral antenna)

This clause applies to EUT to which clause 4.2.6 does not apply. Such EUT are generally known as integral antenna or

dedicated antenna equipment.

The EUT shall be tested with its antenna fitted in a manner typical of normal intended use.

ETSI
---------------------- Page: 11 ----------------------
SIST EN 301 489-17 V3.1.1:2017
10 ETSI EN 301 489-17 V3.1.1 (2017-02)
4.2.8 Equipment with more than one antenna

If the EUT has more than one antenna port, e.g. separate antennas for Tx and Rx or separate antennas for different

operating frequencies or diversity antennas, then:

• If clause 4.2.6 applies to all the antenna ports, then the EUT may be tested according to clause 4.2.6, with all

antenna ports treated the same.
• Otherwise it shall be tested according to clause 4.2.7.

NOTE: The reason is that replacing one antenna by a transmission line may affect the operation of any other

antennas.
4.3 Exclusion bands

The frequencies on which the transmitter part of the EUT is intended to operate shall be excluded from radiated

emission measurements when performed in transmit mode of operation.

There shall be no frequency exclusion band applied to emission measurements of the receiver part of transceivers or the

stand alone receiver under test, and/or associated ancillary equipment.

The exclusion band for immunity testing of equipment operating in the 2,4 GHz band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -120 MHz, i.e. 2 280 MHz;

• upper limit of exclusion band = highest allocated band edge frequency +120 MHz, i.e. 2 603,5 MHz.

The exclusion band for immunity testing of equipment operating in the 5 GHz Wi-Fi band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -270 MHz, i.e. 4 880 MHz;

• upper limit of exclusion band = highest allocated band edge frequency +270 MHz, i.e. 5 995 MHz.

The exclusion band for immunity testing of equipment operating in the 5,8 GHz band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -270 MHz, i.e. 5 455 MHz;

• as the immunity requirements have an upper frequency range of 6 GHz and any upper edge exclusion band

would be greater than this for the 5,8 GHz band. The above frequency shall also be regarded as the upper end

of the test range.

NOTE: These receiver exclusion band ranges align with the relevant blocking test ranges.

4.4 Narrow band responses on receivers or receivers which are
part of transceivers
The provision of ETSI EN 301 489-1 [1], clause 4.4 shall apply.
4.5 Normal test modulati
...

ETSI EN 301 489-17 V3.1.1 (2017-02)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 17: Specific conditions for
Broadband Data Transmission Systems;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-17 V3.1.1 (2017-02)
Reference
REN/ERM-EMC-335
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-17 V3.1.1 (2017-02)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definitions and abbreviations ................................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.0 General .......................................................................................................................................................... 8

4.2.1 Arrangements for test signals at the input of transmitters ............................................................................. 8

4.2.2 Arrangements for test signals at the output of transmitters ........................................................................... 9

4.2.3 Arrangements for test signals at the input of receivers ................................................................................. 9

4.2.4 Arrangements for test signals at the output of receivers ............................................................................... 9

4.2.5 Arrangements for testing transmitter and receiver together (as a system) .................................................... 9

4.2.6 Equipment with an external antenna connector ............................................................................................ 9

4.2.7 Equipment without an external antenna connector (integral antenna) .......................................................... 9

4.2.8 Equipment with more than one antenna ...................................................................................................... 10

4.3 Exclusion bands ................................................................................................................................................ 10

4.4 Narrow band responses on receivers or receivers which are part of transceivers ............................................. 10

4.5 Normal test modulation .................................................................................................................................... 10

5 Performance assessment ......................................................................................................................... 11

5.1 General ............................................................................................................................................................. 11

5.2 Arrangements for the assessment of host dependant equipment and plug-in cards .......................................... 11

5.2.0 Introduction................................................................................................................................................. 11

5.2.1 Alternative A: composite equipment .......................................................................................................... 11

5.2.2 Alternative B: use of a test jig or host ......................................................................................................... 11

5.3 Assessment procedures ..................................................................................................................................... 12

5.4 Ancillary equipment ......................................................................................................................................... 12

5.5 Equipment classification .................................................................................................................................. 12

6 Performance criteria ............................................................................................................................... 12

6.1 General performance criteria ............................................................................................................................ 12

6.2 Performance table ............................................................................................................................................. 13

6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) .............................................. 13

6.4 Performance criteria for Transient phenomena applied to Transmitters (TT) .................................................. 14

6.5 Performance criteria for Continuous phenomena applied to Receivers (CR) ................................................... 14

6.6 Performance criteria for Transient phenomena applied to Receivers (TR) ...................................................... 14

7 Applicability overview ........................................................................................................................... 14

7.1 Emission ........................................................................................................................................................... 14

7.1.1 General ........................................................................................................................................................ 14

7.1.2 Special conditions ....................................................................................................................................... 14

7.2 Immunity .......................................................................................................................................................... 14

7.2.1 General ........................................................................................................................................................ 14

7.2.2 Special conditions ....................................................................................................................................... 15

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 16

Annex B (informative): Examples of radio equipment in the scope of the present document ........ 18

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-17 V3.1.1 (2017-02)

B.1 Introduction ............................................................................................................................................ 18

B.2 Data transmission systems operating in the 2,4 GHz ISM band and using wide band modulation

techniques ............................................................................................................................................... 18

B.3 5 GHz high performance RLAN systems ............................................................................................... 18

B.4 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz ........................ 18

B.5 Broadband data transmitting/BWA Terminal Stations ........................................................................... 18

B.6 Multi-Gigabit Wireless Systems (MGWS) ............................................................................................ 18

Annex C (informative): Change History .............................................................................................. 19

History .............................................................................................................................................................. 20

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-17 V3.1.1 (2017-02)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.12] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated

EFTA regulations.

The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 30 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-17 V3.1.1 (2017-02)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of

measurements for Broadband Data Transmission System equipment, as detailed in annex B.

Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are

not included in the present document. Such technical specifications are found in the relevant product standards for the

effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

wideband data communication systems.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] under the

conditions identified in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

http://docbox.etsi.org/Reference.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.1.1) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-17 V3.1.1 (2017-02)

[i.3] ETSI EN 301 893: "Broadband Radio Access Networks (BRAN); 5 GHz high performance

RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE

Directive".

[i.4] ETSI EN 302 502: "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data

transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the

R&TTE Directive".

[i.5] ETSI EN 302 544-2: "Broadband Data Transmission Systems operating in the 2 500 MHz to

2 690 MHz frequency band; Part 2: TDD User Equipment Stations; Harmonized EN covering the

essential requirements of article 3.2 of the R&TTE Directive".

[i.6] ETSI EN 302 567: "WAS/RLAN systems; Multiple-Gigabit WAS/RLAN equipment operating in

the 60 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU".

[i.7] ETSI EN 302 623: "Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz

frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of

article 3.2 of the R&TTE Directive".

[i.8] ETSI EN 300 328: "Wideband transmission systems; Data transmission equipment operating in the

2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering

the essential requirements of article 3.2 of Directive 2014/53/EU".
[i.9] Void.

[i.10] ETSI EN 301 908-19: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 19: OFDMA TDD WMAN (Mobile

WiMAXTM) TDD User Equipment (UE)".

[i.11] ETSI EN 301 908-21: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile

WiMAX ) FDD User Equipment (UE)".

[i.12] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following

apply:

Equipment Under Test (EUT): equipment subject to the performance requirements of the present document

fixed station: equipment intended for use in a fixed location and fitted with one or more antennas

NOTE: The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.

hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person

NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna

socket(s) or integral antenna(s) or both.

host: any equipment which has complete user functionality when not connected to the radio equipment part and to

which the radio equipment part provides additional functionality and to which connection is necessary for the radio

equipment part to offer functionality
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-17 V3.1.1 (2017-02)

plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host

systems, using their control functions and power supply

stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally

used on a stand-alone basis
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
ACK ACKnowledgement
ARQ Automatic Retransmission reQuest
BRAN Broadband Radio Access Networks
BWA Broadband Wireless Access
CR Continuous phenomena applied to Receivers
CT Continuous phenomena applied to Transmitters
DC Direct Current
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio Matters
EUT Equipment Under Test
ISM Industrial, Scientific and Medical
MGWS Multi-Gigabit Wireless Systems
MUS Maximum Usable Sensitivity
NACK Not ACKnowledgement
RF Radio Frequency
RLAN Radio Local Area Network
TR Transient phenomena applied to Receivers
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as

appropriate. Further product related test conditions for wideband data communications systems are specified in

clauses 4.2 to 4.5.

The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires

connection to a host equipment to function shall use the test configuration as defined by the manufacturer. In all cases

the EUT shall be exercised in a manner representative of normal intended use.
4.2 Arrangements for test signals
4.2.0 General
The provisions of ETSI EN 301 489-1 [1], clause 4.2 shall apply.
4.2.1 Arrangements for test signals at the input of transmitters

The provisions of ETSI EN 301 489-1 [1], clause 4.2.1 shall apply with the following modifications.

The wanted signals and/or controls required to establish a communications link shall be defined by the manufacturer.

The transmitter shall be operated at maximum rated power.
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 489-17 V3.1.1 (2017-02)
4.2.2 Arrangements for test signals at the output of transmitters

The provisions of ETSI EN 301 489-1 [1], clause 4.2.2 shall apply with the following modifications.

The manufacturer may provide a suitable companion receiver that can be used to receive messages or to set up a

communication link.
4.2.3 Arrangements for test signals at the input of receivers

The provisions of ETSI EN 301 489-1 [1], clause 4.2.3 shall apply with the following modifications.

The wanted signals required to establish a communications link shall be defined by the manufacturer.

The level of the wanted signal at the input of the receiver shall be at least 30 dB above the declared Maximum Usable

Sensitivity (MUS).
4.2.4 Arrangements for test signals at the output of receivers

The measuring equipment for the output signal from the receiver under test shall be located outside the test

environment.

It shall be possible to assess the performance of the equipment by appropriately monitoring the receiver output.

If the receiver has an output connector or port providing the wanted output signal, then this port shall be used via a

cable, consistent with the standard cable used in normal operation, connected to the external measuring equipment

outside the test environment. The measuring equipment may be supplied by the manufacturer.

Precautions shall be taken to ensure that any effect on the test due to the coupling means is minimized.

The manufacturer may provide a suitable companion transmitter that can be used to transmit messages or to set up a

communication link.
4.2.5 Arrangements for testing transmitter and receiver together
(as a system)
The provisions of ETSI EN 301 489-1 [1], clause 4.2.5 shall apply.

The manufacturer may provide a suitable companion transceiver or transmitter and receiver that can be used to send and

receive messages or to set up a communication link.

Both the EUT and the companion equipment shall transmit the normal test modulation. Further, the output of the radio

equipment under test shall be monitored by the test system.
4.2.6 Equipment with an external antenna connector

If access to the antenna connector involves modification or dismantling of the EUT then this clause does not apply.

The EUT may be tested with its antenna removed.

In the case of testing with the antenna removed, the wanted RF input and output signals shall be delivered between the

EUT antenna connector and the measuring and/or test equipment by a shielded transmission line, such as a coaxial

cable. Adequate measures shall be taken to minimize the effect of common mode currents on the transmission line at

the point of entry to the EUT and at the measuring/test equipment.
4.2.7 Equipment without an external antenna connector (integral antenna)

This clause applies to EUT to which clause 4.2.6 does not apply. Such EUT are generally known as integral antenna or

dedicated antenna equipment.

The EUT shall be tested with its antenna fitted in a manner typical of normal intended use.

ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 301 489-17 V3.1.1 (2017-02)
4.2.8 Equipment with more than one antenna

If the EUT has more than one antenna port, e.g. separate antennas for Tx and Rx or separate antennas for different

operating frequencies or diversity antennas, then:

• If clause 4.2.6 applies to all the antenna ports, then the EUT may be tested according to clause 4.2.6, with all

antenna ports treated the same.
• Otherwise it shall be tested according to clause 4.2.7.

NOTE: The reason is that replacing one antenna by a transmission line may affect the operation of any other

antennas.
4.3 Exclusion bands

The frequencies on which the transmitter part of the EUT is intended to operate shall be excluded from radiated

emission measurements when performed in transmit mode of operation.

There shall be no frequency exclusion band applied to emission measurements of the receiver part of transceivers or the

stand alone receiver under test, and/or associated ancillary equipment.

The exclusion band for immunity testing of equipment operating in the 2,4 GHz band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -120 MHz, i.e. 2 280 MHz;

• upper limit of exclusion band = highest allocated band edge frequency +120 MHz, i.e. 2 603,5 MHz.

The exclusion band for immunity testing of equipment operating in the 5 GHz Wi-Fi band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -270 MHz, i.e. 4 880 MHz;

• upper limit of exclusion band = highest allocated band edge frequency +270 MHz, i.e. 5 995 MHz.

The exclusion band for immunity testing of equipment operating in the 5,8 GHz band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -270 MHz, i.e. 5 455 MHz;

• as the immunity requirements have an upper frequency range of 6 GHz and any upper edge exclusion band

would be greater than this for the 5,8 GHz band. The above frequency shall also be regarded as the upper end

of the test range.

NOTE: These receiver exclusion band ranges align with the relevant blocking test ranges.

4.4 Narrow band responses on receivers or receivers which are
part of transceivers
The provision of ETSI EN 301 489-1 [1], clause 4.4 shall apply.
4.5 Normal test modulation

The modulated test signal shall represent normal intended use, and may contain data formatting, error detection and

correction information.
ETSI
---------------------- Page: 10 ----------------------
11 ETSI EN 301 489-17 V3.1.1 (2017-02)
5 Performance assessment
5.1 General

The provision of ETSI EN 301 489-1 [1], clause 5.1 shall apply with the following modification.

The manufacturer shall supply at the time of submission of the equipment for test, the information required in ETSI

EN 301 489-1 [1], clause 5.1 and the following which shall be recorded in the test report:

• the operating frequency range(s) of the equipment and, where applicable, band(s) of operation;

• the type of the equipment, for example: stand-alone or plug-in radio device;
• the host equipment to be combined with the radio equipment for testing;

• the minimum performance level under the application of EMC stress (see clause 6.2);

• the normal test modulation, the format, the type of error correction and any control signals

e.g. ACKnowledgement (ACK)/Not ACKnowledgement (NACK) or Automatic Retransmission

reQuest (ARQ).
5.2 Arrangements for the assessment of host dependant
equipment and plug-in cards
5.2.0 Introduction

For equipment parts for which integration with a host equipment is necessary in order to offer functionality, two

alternative approaches defined in clauses 5.2.1 and 5.2.2 may be used. The manufacturer shal

...

Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 17: Specific conditions for
Broadband Data Transmission Systems;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
Reference
REN/ERM-EMC-335
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definitions and abbreviations ................................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.0 General .......................................................................................................................................................... 8

4.2.1 Arrangements for test signals at the input of transmitters ............................................................................. 8

4.2.2 Arrangements for test signals at the output of transmitters ........................................................................... 9

4.2.3 Arrangements for test signals at the input of receivers ................................................................................. 9

4.2.4 Arrangements for test signals at the output of receivers ............................................................................... 9

4.2.5 Arrangements for testing transmitter and receiver together (as a system) .................................................... 9

4.2.6 Equipment with an external antenna connector ............................................................................................ 9

4.2.7 Equipment without an external antenna connector (integral antenna) .......................................................... 9

4.2.8 Equipment with more than one antenna ...................................................................................................... 10

4.3 Exclusion bands ................................................................................................................................................ 10

4.4 Narrow band responses on receivers or receivers which are part of transceivers ............................................. 10

4.5 Normal test modulation .................................................................................................................................... 10

5 Performance assessment ......................................................................................................................... 11

5.1 General ............................................................................................................................................................. 11

5.2 Arrangements for the assessment of host dependant equipment and plug-in cards .......................................... 11

5.2.0 Introduction................................................................................................................................................. 11

5.2.1 Alternative A: composite equipment .......................................................................................................... 11

5.2.2 Alternative B: use of a test jig or host ......................................................................................................... 11

5.3 Assessment procedures ..................................................................................................................................... 12

5.4 Ancillary equipment ......................................................................................................................................... 12

5.5 Equipment classification .................................................................................................................................. 12

6 Performance criteria ............................................................................................................................... 12

6.1 General performance criteria ............................................................................................................................ 12

6.2 Performance table ............................................................................................................................................. 13

6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) .............................................. 13

6.4 Performance criteria for Transient phenomena applied to Transmitters (TT) .................................................. 14

6.5 Performance criteria for Continuous phenomena applied to Receivers (CR) ................................................... 14

6.6 Performance criteria for Transient phenomena applied to Receivers (TR) ...................................................... 14

7 Applicability overview ........................................................................................................................... 14

7.1 Emission ........................................................................................................................................................... 14

7.1.1 General ........................................................................................................................................................ 14

7.1.2 Special conditions ....................................................................................................................................... 14

7.2 Immunity .......................................................................................................................................................... 14

7.2.1 General ........................................................................................................................................................ 14

7.2.2 Special conditions ....................................................................................................................................... 15

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 16

Annex B (informative): Examples of radio equipment in the scope of the present document ........ 18

ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)

B.1 Introduction ............................................................................................................................................ 18

B.2 Data transmission systems operating in the 2,4 GHz ISM band and using wide band modulation

techniques ............................................................................................................................................... 18

B.3 5 GHz high performance RLAN systems ............................................................................................... 18

B.4 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz ........................ 18

B.5 Broadband data transmitting/BWA Terminal Stations ........................................................................... 18

B.6 Multi-Gigabit Wireless Systems (MGWS) ............................................................................................ 18

Annex C (informative): Summary of changes from previous version ............................................... 19

History .............................................................................................................................................................. 20

ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee

Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the

ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.12] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated

EFTA regulations.

The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of

measurements for Broadband Data Transmission System equipment, as detailed in annex B.

Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are

not included in the present document. Such technical specifications are found in the relevant product standards for the

effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

wideband data communication systems.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] under the

conditions identified in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

http://docbox.etsi.org/Reference.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.1.1) (11-2016): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU ".
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)

[i.3] ETSI EN 301 893: "Broadband Radio Access Networks (BRAN); 5 GHz high performance

RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE

Directive".

[i.4] ETSI EN 302 502: "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data

transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the

R&TTE Directive".

[i.5] ETSI EN 302 544-2: "Broadband Data Transmission Systems operating in the 2 500 MHz to

2 690 MHz frequency band; Part 2: TDD User Equipment Stations; Harmonized EN covering the

essential requirements of article 3.2 of the R&TTE Directive".

[i.6] ETSI EN 302 567: "WAS/RLAN systems; Multiple-Gigabit WAS/RLAN equipment operating in

the 60 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU".

[i.7] ETSI EN 302 623: "Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz

frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of

article 3.2 of the R&TTE Directive".

[i.8] ETSI EN 300 328: "Wideband transmission systems; Data transmission equipment operating in the

2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering

the essential requirements of article 3.2 of Directive 2014/53/EU".
[i.9] Void.

[i.10] ETSI EN 301 908-19: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 19: OFDMA TDD WMAN (Mobile

WiMAXTM) TDD User Equipment (UE)".

[i.11] ETSI EN 301 908-21: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile

WiMAX ) FDD User Equipment (UE)".

[i.12] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following

apply:

Equipment Under Test (EUT): equipment subject to the performance requirements of the present document

fixed station: equipment intended for use in a fixed location and fitted with one or more antennas

NOTE: The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.

hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person

NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna

socket(s) or integral antenna(s) or both.

host: any equipment which has complete user functionality when not connected to the radio equipment part and to

which the radio equipment part provides additional functionality and to which connection is necessary for the radio

equipment part to offer functionality
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)

plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host

systems, using their control functions and power supply

stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally

used on a stand-alone basis
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
ACK ACKnowledgement
ARQ Automatic Retransmission reQuest
BRAN Broadband Radio Access Networks
BWA Broadband Wireless Access
CR Continuous phenomena applied to Receivers
CT Continuous phenomena applied to Transmitters
DC Direct Current
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio Matters
EUT Equipment Under Test
ISM Industrial, Scientific and Medical
MGWS Multi-Gigabit Wireless Systems
MUS Maximum Usable Sensitivity
NACK Not ACKnowledgement
RF Radio Frequency
RLAN Radio Local Area Network
TR Transient phenomena applied to Receivers
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as

appropriate. Further product related test conditions for wideband data communications systems are specified in

clauses 4.2 to 4.5.

The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires

connection to a host equipment to function shall use the test configuration as defined by the manufacturer. In all cases

the EUT shall be exercised in a manner representative of normal intended use.
4.2 Arrangements for test signals
4.2.0 General
The provisions of ETSI EN 301 489-1 [1], clause 4.2 shall apply.
4.2.1 Arrangements for test signals at the input of transmitters

The provisions of ETSI EN 301 489-1 [1], clause 4.2.1 shall apply with the following modifications.

The wanted signals and/or controls required to establish a communications link shall be defined by the manufacturer.

The transmitter shall be operated at maximum rated power.
ETSI
---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
4.2.2 Arrangements for test signals at the output of transmitters

The provisions of ETSI EN 301 489-1 [1], clause 4.2.2 shall apply with the following modifications.

The manufacturer may provide a suitable companion receiver that can be used to receive messages or to set up a

communication link.
4.2.3 Arrangements for test signals at the input of receivers

The provisions of ETSI EN 301 489-1 [1], clause 4.2.3 shall apply with the following modifications.

The wanted signals required to establish a communications link shall be defined by the manufacturer.

The level of the wanted signal at the input of the receiver shall be at least 30 dB above the declared Maximum Usable

Sensitivity (MUS).
4.2.4 Arrangements for test signals at the output of receivers

The measuring equipment for the output signal from the receiver under test shall be located outside the test

environment.

It shall be possible to assess the performance of the equipment by appropriately monitoring the receiver output.

If the receiver has an output connector or port providing the wanted output signal, then this port shall be used via a

cable, consistent with the standard cable used in normal operation, connected to the external measuring equipment

outside the test environment. The measuring equipment may be supplied by the manufacturer.

Precautions shall be taken to ensure that any effect on the test due to the coupling means is minimized.

The manufacturer may provide a suitable companion transmitter that can be used to transmit messages or to set up a

communication link.
4.2.5 Arrangements for testing transmitter and receiver together
(as a system)
The provisions of ETSI EN 301 489-1 [1], clause 4.2.5 shall apply.

The manufacturer may provide a suitable companion transceiver or transmitter and receiver that can be used to send and

receive messages or to set up a communication link.

Both the EUT and the companion equipment shall transmit the normal test modulation. Further, the output of the radio

equipment under test shall be monitored by the test system.
4.2.6 Equipment with an external antenna connector

If access to the antenna connector involves modification or dismantling of the EUT then this clause does not apply.

The EUT may be tested with its antenna removed.

In the case of testing with the antenna removed, the wanted RF input and output signals shall be delivered between the

EUT antenna connector and the measuring and/or test equipment by a shielded transmission line, such as a coaxial

cable. Adequate measures shall be taken to minimize the effect of common mode currents on the transmission line at

the point of entry to the EUT and at the measuring/test equipment.
4.2.7 Equipment without an external antenna connector (integral antenna)

This clause applies to EUT to which clause 4.2.6 does not apply. Such EUT are generally known as integral antenna or

dedicated antenna equipment.

The EUT shall be tested with its antenna fitted in a manner typical of normal intended use.

ETSI
---------------------- Page: 9 ----------------------
10 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
4.2.8 Equipment with more than one antenna

If the EUT has more than one antenna port, e.g. separate antennas for Tx and Rx or separate antennas for different

operating frequencies or diversity antennas, then:

• If clause 4.2.6 applies to all the antenna ports, then the EUT may be tested according to clause 4.2.6, with all

antenna ports treated the same.
• Otherwise it shall be tested according to clause 4.2.7.

NOTE: The reason is that replacing one antenna by a transmission line may affect the operation of any other

antennas.
4.3 Exclusion bands

The frequencies on which the transmitter part of the EUT is intended to operate shall be excluded from radiated

emission measurements when performed in transmit mode of operation.

There shall be no frequency exclusion band applied to emission measurements of the receiver part of transceivers or the

stand alone receiver under test, and/or associated ancillary equipment.

The exclusion band for immunity testing of equipment operating in the 2,4 GHz band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -120 MHz, i.e. 2 280 MHz;

• upper limit of exclusion band = highest allocated band edge frequency +120 MHz, i.e. 2 603,5MHz.

The exclusion band for immunity testing of equipment operating in the 5 GHz Wi-Fi band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -270 MHz, i.e. 4 880 MHz;

• upper limit of exclusion band = highest allocated band edge frequency +270 MHz, i.e. 5 995 MHz.

The exclusion band for immunity testing of equipment operating in the 5,8 GHz band shall be:

• lower limit of exclusion band = lowest allocated band edge frequency -270 MHz, i.e. 5 455 MHz;

• as the immunity requirements have an upper frequency range of 6 GHz and any upper edge exclusion band

would be greater than this for the 5,8 GHz band. The above frequency shall also be regarded as the upper end

of the test range.

NOTE: These receiver exclusion band ranges align with the relevant blocking test ranges.

4.4 Narrow band responses on receivers or receivers which are
part of transceivers
The provision of ETSI EN 301 489-1 [1], clause 4.4 shall apply.
4.5 Normal test modulation

The modulated test signal shall represent normal intended use, and may contain data formatting, error detection and

correction information.
ETSI
---------------------- Page: 10 ----------------------
11 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
5 Performance assessment
5.1 General

The provision of ETSI EN 301 489-1 [1], clause 5.1 shall apply with the following modification.

The manufacturer shall supply at the time of submission of the equipment for test, the information required in ETSI

EN 301 489-1 [1], clause 5.1 and the following which shall be recorded in the test report:

• the operating frequency range(s) of the equipment and, where applicable, band(s) of operation;

• the type of the equipment, for example: stand-alone or plug-in radio device;
• the host equipment to be combined with the radio equipment for testing;

• the minimum performance level under the application of EMC stress (see clause 6.2);

• the normal test modulation, the format, the type of error correction and any control signals

e.g. ACKnowledgement (ACK)/Not ACKnowledgement (NACK) or Automatic Retransmission

reQuest (ARQ).
5.2 Arrangements for the assessment of host dependant
equipment and plug-in cards
5.2.0 Introduction
...

Draft ETSI EN 301 489-17 V3.1.0 (2016-04)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 17: Specific conditions for
Broadband Data Transmission Systems;
Harmonised Standard covering the essential requirements
of article 3.1(b) of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-17 V3.1.0 (2016-04)
Reference
REN/ERM-EMC-335
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-17 V3.1.0 (2016-04)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definitions and abbreviations ................................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.0 General .......................................................................................................................................................... 8

4.2.1 Arrangements for test signals at the input of transmitters ............................................................................. 8

4.2.2 Arrangements for test signals at the output of transmitters ........................................................................... 8

4.2.3 Arrangements for test signals at the input of receivers ................................................................................. 9

4.2.4 Arrangements for test signals at the output of receivers ............................................................................... 9

4.2.5 Arrangements for testing transmitter and receiver together (as a system) .................................................... 9

4.3 Exclusion bands .................................................................................................................................................. 9

4.4 Narrow band responses on receivers or receivers which are part of transceivers ............................................. 10

4.5 Normal test modulation .................................................................................................................................... 10

5 Performance assessment ......................................................................................................................... 10

5.1 General ............................................................................................................................................................. 10

5.2 Arrangements for the assessment of host dependant equipment and plug-in cards .......................................... 10

5.2.0 Introduction................................................................................................................................................. 10

5.2.1 Alternative A: composite equipment .......................................................................................................... 10

5.2.2 Alternative B: use of a test jig or host ......................................................................................................... 11

5.3 Assessment procedures ..................................................................................................................................... 11

5.4 Ancillary equipment ......................................................................................................................................... 11

5.5 Equipment classification .................................................................................................................................. 11

6 Performance criteria ............................................................................................................................... 11

6.1 General performance criteria ............................................................................................................................ 11

6.2 Performance table ............................................................................................................................................. 12

6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) .............................................. 12

6.4 Performance criteria for Transient phenomena applied to Transmitters (TT) .................................................. 12

6.5 Performance criteria for Continuous phenomena applied to Receivers (CR) ................................................... 12

6.6 Performance criteria for Transient phenomena applied to Receivers (TR) ...................................................... 13

7 Applicability overview ........................................................................................................................... 13

7.1 Emission ........................................................................................................................................................... 13

7.1.1 General ........................................................................................................................................................ 13

7.1.2 Special conditions ....................................................................................................................................... 13

7.2 Immunity .......................................................................................................................................................... 13

7.2.1 General ........................................................................................................................................................ 13

7.2.2 Special conditions ....................................................................................................................................... 13

Annex A (normative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 14

Annex B (informative): Examples of radio equipment in the scope of the present document ........ 16

B.1 Introduction ............................................................................................................................................ 16

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-17 V3.1.0 (2016-04)

B.2 Data transmission systems operating in the 2,4 GHz ISM band and using wide band modulation

techniques ............................................................................................................................................... 16

B.3 5 GHz high performance RLAN systems ............................................................................................... 16

B.4 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz ........................ 16

B.5 Broadband data transmitting/BWA Terminal Stations ........................................................................... 16

B.6 Multi-Gigabit Wireless Systems (MGWS) ............................................................................................ 16

Annex C (informative): Bibliography ................................................................................................... 17

History .............................................................................................................................................................. 18

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-17 V3.1.0 (2016-04)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote

phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.12] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated

EFTA regulations.

The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-17 V3.1.0 (2016-04)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Broadband Data Transmission

System equipment, as detailed in annex B, in respect of ElectroMagnetic Compatibility (EMC).

Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are

not included in the present document. Such technical specifications are found in the relevant product standards for the

effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

wideband data communication systems.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

http://docbox.etsi.org/Reference.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.1.0) (04-2016): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Harmonised Standard covering the essential requirements of

article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the

Directive 2014/30/EU; Part 1: Common technical requirements".
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.

[i.3] ETSI EN 301 893: "Broadband Radio Access Networks (BRAN); 5 GHz high performance

RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE

Directive".
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-17 V3.1.0 (2016-04)

[i.4] ETSI EN 302 502: "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data

transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the

R&TTE Directive".

[i.5] ETSI EN 302 544-2: "Broadband Data Transmission Systems operating in the 2 500 MHz to

2 690 MHz frequency band; Part 2: TDD User Equipment Stations; Harmonized EN covering the

essential requirements of article 3.2 of the R&TTE Directive".

[i.6] ETSI EN 302 567: "WAS/RLAN systems; Multiple-Gigabit WAS/RLAN equipment operating in

the 60 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU".

[i.7] ETSI EN 302 623: "Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz

frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of

article 3.2 of the R&TTE Directive".

[i.8] ETSI EN 300 328: "Wideband transmission systems; Data transmission equipment operating in the

2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering

the essential requirements of article 3.2 of the Directive 2014/53/EU".
[i.9] Void.

[i.10] ETSI EN 301 908-19: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 19: OFDMA TDD WMAN (Mobile

WiMAXTM) TDD User Equipment (UE)".

[i.11] ETSI EN 301 908-21: "IMT cellular networks; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile

WiMAXTM) FDD User Equipment (UE)".

[i.12] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of
Directive 2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following

apply:

Equipment Under Test (EUT): equipment under test and subject to the performance requirements of the present

document

fixed station: equipment intended for use in a fixed location and fitted with one or more antennas

NOTE: The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.

hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person

NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna

socket(s) or integral antenna(s) or both.

host: any equipment which has complete user functionality when not connected to the radio equipment part and to

which the radio equipment part provides additional functionality and to which connection is necessary for the radio

equipment part to offer functionality

plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host

systems, using their control functions and power supply

stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally

used on a stand-alone basis
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-17 V3.1.0 (2016-04)
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
ACK ACKnowledgement
ARQ Automatic Retransmission reQuest
BRAN Broadband Radio Access Networks
BWA Broadband Wireless Access
CR Continuous phenomena applied to Receivers
CT Continuous phenomena applied to Transmitters
DC Direct Current
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio Matters
EUT Equipment Under Test
HIPERLAN HIgh PErformance Radio Local Area Network
ISM Industrial, Scientific and Medical
MGWS Multi-Gigabit Wireless Systems
MUS Maximum Usable Sensitivi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.