SIST EN ISO 6270-2:2018
(Main)Paints and varnishes - Determination of resistance to humidity - Part 2: Condensation (in-cabinet exposure with heated water reservoir) (ISO 6270-2:2017)
Paints and varnishes - Determination of resistance to humidity - Part 2: Condensation (in-cabinet exposure with heated water reservoir) (ISO 6270-2:2017)
This document specifies the general conditions and procedures which need to be observed when testing
coated test specimens in constant condensation-water atmospheres or in alternating condensationwater
atmospheres, in order to ensure that the results of tests carried out in different laboratories are
reproducible.
NOTE The shape and preparation of the test specimens, the duration of the test and the assessment of the
test results are not covered in this document.
Beschichtungsstoffe - Bestimmung der Beständigkeit gegen Feuchtigkeit - Teil 2: Kondensation (Beanspruchung in einer Klimakammer) (ISO 6270-2:2017)
Dieser Teil von ISO 6270 legt die allgemeinen Bedingungen und Verfahren fest, die bei der Beanspruchung von Probenkörpern in Kondenswasser-Konstantklimaten oder Kondenswasser-Wechselklimaten einge¬hal-ten werden müssen, damit bei Prüfungen in verschiedenen Laboratorien die Ergebnisse vergleichbar sind.
ANMERKUNG Probenform, Probenvorbereitung, Prüfdauer und Beurteilung der Ergebnisse sind nicht Gegen¬stand dieses Teiles von ISO 6270.
Peintures et vernis - Détermination de la résistance à l'humidité - Partie 2: Condensation (exposition en enceinte avec réservoir à eau chauffée) (ISO 6270-2:2017)
ISO 6270-2:2017 définit les conditions et modes opératoires généraux qui doivent être respectés lors de l'essai, sur éprouvettes revêtues, en atmosphères de condensation d'eau constante ou en atmosphères de condensation d'eau alternée, afin de s'assurer de la reproductibilité des résultats d'essais réalisés dans différents laboratoires.
Barve in laki - Ugotavljanje odpornosti proti vlagi - 2. del: Kondenzacija (izpostavljenost v komori z ogrevanim rezervoarjem z vodo) (ISO 6270-2:2017)
Ta dokument določa splošne pogoje in postopke, ki jih je treba upoštevati pri preskušanju premazanih primerkov v atmosferi, kjer je konstantno kondenzacija/voda, ali kjer se taki atmosferi izmenjujeta. Ti postopki zagotavljajo, da so rezultati preskusov, izvedenih v različnih laboratorijih, ponovljivi.
OPOMBA: Ta dokument ne zajema oblike in priprave preskusnih primerkov, trajanja preskusa in tolmačenja rezultatov preskusa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6270-2:2018
01-april-2018
Barve in laki - Ugotavljanje odpornosti proti vlagi - 2. del: Kondenzacija
(izpostavljenost v komori z ogrevanim rezervoarjem z vodo) (ISO 6270-2:2017)
Paints and varnishes - Determination of resistance to humidity - Part 2: Condensation (in
-cabinet exposure with heated water reservoir) (ISO 6270-2:2017)
Beschichtungsstoffe - Bestimmung der Beständigkeit gegen Feuchtigkeit - Teil 2:
Kondensation (Beanspruchung in einer Klimakammer) (ISO 6270-2:2017)
Peintures et vernis - Détermination de la résistance à l'humidité - Partie 2: Condensation
(exposition en enceinte avec réservoir à eau chauffée) (ISO 6270-2:2017)
Ta slovenski standard je istoveten z: EN ISO 6270-2:2018
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 6270-2:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6270-2:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 6270-2:2018
EN ISO 6270-2
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2018
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 6270-2:2005
English Version
Paints and varnishes - Determination of resistance to
humidity - Part 2: Condensation (in-cabinet exposure with
heated water reservoir) (ISO 6270-2:2017)
Peintures et vernis - Détermination de la résistance à Beschichtungsstoffe - Bestimmung der Beständigkeit
l'humidité - Partie 2: Condensation (exposition en gegen Feuchtigkeit - Teil 2: Kondensation
enceinte avec réservoir à eau chauffée) (ISO 6270- (Beanspruchung in einer Klimakammer) (ISO 6270-
2:2017) 2:2017)
This European Standard was approved by CEN on 25 November 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6270-2:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6270-2:2018
EN ISO 6270-2:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6270-2:2018
EN ISO 6270-2:2018 (E)
European foreword
This document (EN ISO 6270-2:2018) has been prepared by Technical Committee ISO/TC 35/SC 9
“General test methods for paints and varnishes” in collaboration with Technical Committee CEN/TC 139
“Paints and varnishes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2018, and conflicting national standards shall be
withdrawn at the latest by July 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6270-2:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6270-2:2017 has been approved by CEN as EN ISO 6270-2:2018 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 6270-2:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 6270-2:2018
INTERNATIONAL ISO
STANDARD 6270-2
Second edition
2017-11
Paints and varnishes — Determination
of resistance to humidity —
Part 2:
Condensation (in-cabinet exposure
with heated water reservoir)
Peintures et vernis — Détermination de la résistance à l'humidité —
Partie 2: Condensation (exposition en enceinte avec réservoir à eau
chauffée)
Reference number
ISO 6270-2:2017(E)
©
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 6270-2:2018
ISO 6270-2:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 6270-2:2018
ISO 6270-2:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation . 1
5 Limitations . 2
6 Principle . 2
7 Test atmospheres . 2
8 Apparatus . 3
9 Procedure. 4
9.1 Filling the floor trough . 4
9.2 Test specimens . 5
9.3 Arrangement of the test specimens . 5
9.4 Determination of the comparison quantity of condensation water . 5
9.5 Test sequence . 5
9.5.1 Start-up . 5
9.5.2 Condensation atmosphere with constant humidity (CH). 6
9.5.3 Condensation atmosphere with alternation of humidity and air
temperature (AHT) . 6
9.5.4 Condensation atmosphere with alternation of air temperature (AT) . 6
9.6 Interruptions . 6
9.7 End of test . 6
10 Evaluation . 6
11 Precision . 7
12 Test report . 7
Bibliography . 8
© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 6270-2:2018
ISO 6270-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes.
This second edition cancels and replaces the first edition (ISO 6270-2:2005), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— a principle clause has been added;
— the terms and definitions clause has been added;
— a limitations clause concerning the use of other than standard test conditions has been added;
— the recommendation to use distilled or deionized water for filling the trough has been changed;
— a requirement has been added to make sure that condensation forms on all test specimens;
— a method for the determination of the comparison quantity of condensation water has been added;
— information on precision has been added;
— the normative references have been updated.
A list of all parts in the ISO 6270 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 6270-2:2018
ISO 6270-2:2017(E)
Introduction
This document is intended to give consistent conditions and procedures for the conditioning of pre-
prepared test specimens which are to be evaluated for defects, which may develop when they are
subjected to humid ambient atmospheres such as constant condensation-water atmospheres or
alternating condensation-water atmospheres.
The tests are designed to clarify the behaviour of the test specimens in humid ambient atmospheres,
and to pinpoint any defects in the protection of the test specimens against corrosion. The testing of
coatings in these atmospheres does not necessarily give lifetime prediction data.
After conditioning, the test specimens are evaluated either in accordance with agreed documents, such
[1]
as the appropriate part(s) of ISO 4628 or by procedures agreed between the interested parties.
© ISO 2017 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 6270-2:2018
---------------------- Page: 12 ----------------------
SIST EN ISO 6270-2:2018
INTERNATIONAL STANDARD ISO 6270-2:2017(E)
Paints and varnishes — Determination of resistance to
humidity —
Part 2:
Condensation (in-cabinet exposure with heated water
reservoir)
1 Scope
This document specifies the general conditions and procedures which need to be observed when testing
coated test specimens in constant condensation-water atmospheres or in alternating condensation-
water atmospheres, in order to ensure that the results of tests carried out in different laboratories are
reproducible.
NOTE The shape and preparation of the test specimens, the duration of the test and the assessment of the
test results are not covered in this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3
...
SLOVENSKI STANDARD
oSIST prEN ISO 6270-2:2016
01-oktober-2016
Barve in laki - Ugotavljanje odpornosti proti vlagi - 2. del: Kondenzacija
(izpostavljenost v vlažni komori) (ISO/DIS 6270-2:2016)
Paints and varnishes - Determination of resistance to humidity - Part 2: Condensation (in
-cabinet exposure) (ISO/DIS 6270-2:2016)
Beschichtungsstoffe - Bestimmung der Beständigkeit gegen Feuchtigkeit - Teil 2:
Kondensation (Beanspruchung in einer Klimakammer) (ISO/DIS 6270-2:2016)
Peintures et vernis - Détermination de la résistance à l'humidité - Partie 2: Condensation
(exposition en enceinte) (ISO/DIS 6270-2:2016)
Ta slovenski standard je istoveten z: prEN ISO 6270-2
ICS:
87.040 Barve in laki Paints and varnishes
oSIST prEN ISO 6270-2:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 6270-2:2016
---------------------- Page: 2 ----------------------
oSIST prEN ISO 6270-2:2016
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6270-2
ISO/TC 35/SC 9 Secretariat: BSI
Voting begins on: Voting terminates on:
2016-08-11 2016-11-02
Paints and varnishes — Determination of resistance to
humidity —
Part 2:
Condensation (in-cabinet exposure)
Peintures et vernis — Détermination de la résistance à l’humidité —
Partie 2: Condensation (exposition en enceinte)
ICS: 87.040
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 6270-2:2016(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2016
---------------------- Page: 3 ----------------------
oSIST prEN ISO 6270-2:2016
ISO/DIS 6270-2:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 6270-2:2016
ISO/DIS 6270-2:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Designation . 1
4 Principle . 1
5 Test atmospheres . 1
6 Apparatus . 3
6.1 Climatic chamber . 3
6.2 Installation of the climatic chamber . 4
6.3 Device for accommodating the test specimens . 4
7 Procedure. 5
7.1 Filling the floor trough . 5
7.2 Test specimens . 5
7.3 Arrangement of the test specimens . 5
7.4 Determination of the comparison quantity of condensation water . 5
7.5 Test sequence . 5
7.5.1 Start-up . 5
7.5.2 Condensation atmosphere with constant humidity (CH). 6
7.5.3 Condensation atmosphere with alternation of humidity and air
temperature (AHT) . 6
7.5.4 Condensation atmosphere with alternation of air temperature (AT) . 6
7.6 Interruptions . 6
7.7 End of test . 6
8 Evaluation . 7
9 Precision . 7
10 Test report . 7
Bibliography . 8
© ISO 2016 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 6270-2:2016
ISO/DIS 6270-2:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 35/SC 9, General test methods for paints and
varnishes.
This second edition cancels and replaces the first edition (ISO 6270-2:2005), which has been technically
revised. The main changes are:
a) a principle clause has been added;
b) the recommendation to use distilled or deionized water for filling the trough has been changed;
c) a requirement has been added to make sure that condensation forms on all test panels;
d) a method for the determination of the comparison quantity of condensation water has been added;
e) information on precision has been added;
f) the normative references have been updated.
ISO 6270, Paints and varnishes — Determination of resistance to humidity, consists of the following parts:
— Part 1: Condensation (single-sided exposure)
— Part 2: Condensation (in-cabinet exposure)
— Part 3: Condensation (in-cabinet exposure with rotating test specimen)
iv © ISO 2016 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 6270-2:2016
ISO/DIS 6270-2:2016(E)
Introduction
ISO 6270 is intended to give consistent conditions and procedures for the conditioning of pre-prepared
test specimens which are to be evaluated for defects which may develop when they are subjected
to humid ambient atmospheres such as constant condensation-water atmospheres or alternating
condensation-water atmospheres.
The tests are designed to clarify the behaviour of the test specimens in humid ambient atmospheres,
and to pinpoint any defects in the protection of the test specimens against corrosion. The testing of
coatings in these atmospheres does not necessarily give lifetime prediction data.
After conditioning, the test specimens are evaluated either in accordance with agreed International
[1]
Standards, such as the appropriate part(s) of ISO 4628 or by procedures agreed between the
interested parties.
© ISO 2016 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST prEN ISO 6270-2:2016
---------------------- Page: 8 ----------------------
oSIST prEN ISO 6270-2:2016
DRAFT INTERNATIONAL STANDARD ISO/DIS 6270-2:2016(E)
Paints and varnishes — Determination of resistance to
humidity —
Part 2:
Condensation (in-cabinet exposure)
1 Scope
This part of ISO 6270 specifies the general conditions and procedures which need to be observed
when testing coated test specimens in constant condensation-water atmospheres or in alternating
condensation-water atmospheres, in order to ensure that the results of tests carried out in different
laboratories are reproducible.
NOTE The shape and preparation of the test specimens, the duration of the test and the assessment of the
test results are not covered in this part of ISO 6270.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 3270, Paints and varnishes and their raw materials — Temperatures and humidities for conditioning
and testing
3 Designation
The condensation-water test atmospheres are designated as follows:
Test atmosphere CH Condensation atmosphere with constant humidity
AHT Condensation atmosphere with alternating humidity and air temperature
AT Condensation atmosphere with alternating air temperature
4 Principle
A coated test panel is exposed to condensation in a climatic chamber and the effects of the exposure are
evaluated by criteria agreed in advance between the interested parties, these criteria usually being of
a subjective nature.
5 Test atmospheres
Condensation-water test atmospheres promote the condensation of atmospheric humidity on the
surfaces of test specimens, the temperatures of which are lower than the temperature of the saturated
air in the climatic chamber, due to radiation onto the chamber walls or to the cooling of the test
specimen.
The atmospheric temperature in the cli
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.