Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification

This European Standard specifies the requirements for factory made phenolic foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 200 °C to + 120 °C.
The products are manufactured in the form of blocks, faced or unfaced, boards, pipe sections, segments and prefabricated ware.
This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.
This standard does not specify the required level of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.
Products with a declared thermal conductivity greater than 0,050 W/(m·K) at 10 °C are not covered by this standard.
This standard does not cover products for in situ-insulation (blowing or pouring) or products for the insulation of the building structure.
This standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.

Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Phenolharzschaum (PF) - Spezifikation

Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en mousse phénolique (PF) - Spécification

Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz fenolne pene (PF) - Specifikacija

General Information

Status
Not Published
Public Enquiry End Date
29-Aug-2012
Technical Committee
Current Stage
98 - Abandoned project (Adopted Project)
Start Date
15-Jul-2015
Due Date
20-Jul-2015
Completion Date
15-Jul-2015

Relations

Buy Standard

Draft
EN 14314:2010/kFprA1:2012
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14314:2010/kFprA1:2012
01-julij-2012
Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije -
Proizvodi iz fenolne pene (PF) - Specifikacija
Thermal insulation products for building equipment and industrial installations - Factory
made phenolic foam (PF) products - Specification
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische
Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Phenolharzschaum (PF)
- Spezifikation
Produits isolants thermiques pour l'équipement du bâtiment et les installations
industrielles - Produits manufacturés en mousse phénolique (PF) - Spécification
Ta slovenski standard je istoveten z: EN 14314:2009/FprA1
ICS:
91.100.60 0DWHULDOL]DWRSORWQRLQ Thermal and sound insulating
]YRþQRL]RODFLMR materials
SIST EN 14314:2010/kFprA1:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14314:2010/kFprA1:2012

---------------------- Page: 2 ----------------------

SIST EN 14314:2010/kFprA1:2012


EUROPEAN STANDARD
FINAL DRAFT
EN 14314:2009
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
May 2012
ICS 91.100.60
English Version
Thermal insulation products for building equipment and industrial
installations - Factory made phenolic foam (PF) products -
Specification
Produits isolants thermiques pour l'équipement du bâtiment Wärmedämmstoffe für die technische Gebäudeausrüstung
et les installations industrielles - Produits manufacturés en
und für betriebstechnische Anlagen in der Industrie -
mousse phénolique (PF) - Spécification Werkmäßig hergestellte Produkte aus Phenolharzschaum
(PF) - Spezifikation
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 88.

This draft amendment A1, if approved, will modify the European Standard EN 14314:2009. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14314:2009/FprA1:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 14314:2010/kFprA1:2012
EN 14314:2009/FprA1:2012 (E)
Contents Page
Foreword .3
1 Modifications to 4.2.2, Dimensions and tolerances .4
2 Modifications to 4.2.3, Dimensional stability .4
3 Modification to 4.2.5.3, Durability of thermal resistance against ageing .5
4 Modifications to 4.3.5, Compression resistance properties .5
5 Modifications to 4.3.7, Water absorption .5
6 Modification to 4.3.8, Closed cell content .5
7 Modification to 5.2, Conditioning .5
8 Modifications to 5.3.1, General .5
9 Modification to 5.3.2, Thermal conductivity .5
10 Modifications to ZA.1, Scope and relevant characteristics .6
11 Modification to ZA.2, Procedures for for attestation of conformity of factory made
phenolic foam products .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.