SIST EN 12697-2:2015
(Main)Bituminous mixtures - Test method - Part 2: Determination of particle size distribution
Bituminous mixtures - Test method - Part 2: Determination of particle size distribution
This European Standard specifies a procedure for the determination of the particle size distribution of the aggregates of bituminous mixtures by sieving. The test is applicable to aggregates recovered after binder extraction in accordance with EN 12697-1 or EN 12697-39.
The applicability of this European Standard is described in the product standards for bituminous mixtures.
NOTE Fibres, solid (non soluble during extraction) additives and (some) binder modifiers influence the test result.
Asphalt - Prüfverfahren - Teil 2: Korngrößenverteilung
Diese Europäische Norm legt ein Verfahren für die Bestimmung der Korngrößenverteilung der Gesteinskör-nungen in Asphalt mittels Siebanalyse fest. Die Prüfung ist für Gesteinskörnungen, die nach Extraktion des Bindemittels nach EN 12697-1 oder EN 12697-39 rückgewonnen wurden, anwendbar.
Die Anwendbarkeit dieser Europäischen Norm ist in den Produktnormen für Asphalt beschrieben.
ANMERKUNG Fasern, feste Zusatzstoffe (die bei der Extraktion nicht in Lösung gehen) und (einige) Modifizierungs-mittel für Bindemittel beeinflussen das Prüfergebnis.
Mélanges bitumineux - Méthode d'essai - Partie 2: Granulométrie
La présente Norme européenne spécifie un mode opératoire pour la détermination de la composition granulométrique des granulats dans les mélanges bitumineux, par tamisage. L'essai s'applique aux granulats récupérés après extraction du liant selon l'EN 12697-1 ou l'EN 12697-39.
L'applicabilité de la présente Norme européenne est décrite dans les normes de produits relatives aux mélanges bitumineux.
NOTE Les fibres, additifs solides (non solubles durant l'extraction) et (certains) modificateurs de liants influencent le résultat de l'essai.
Bitumenske zmesi - Preskusne metode - 2. del: Ugotavljanje zrnavosti
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumenske zmesi - Preskusne metode - 2. del: Ugotavljanje zrnavostiAsphalt - Prüfverfahren - Teil 2: KorngrößenverteilungMélanges bitumineux - Méthode d'essai - Partie 2: GranulométrieBituminous mixtures - Test method - Part 2: Determination of particle size distribution93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-2:2015SIST EN 12697-2:2015en,fr,de01-julij-2015SIST EN 12697-2:2015SLOVENSKI
STANDARDSIST EN 12697-2:2004+A1:20071DGRPHãþD
SIST EN 12697-2:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-2
April 2015 ICS 93.080.20 Supersedes EN 12697-2:2002+A1:2007English Version
Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution
Mélanges bitumineux - Méthode d'essai - Partie 2: Granulométrie
Asphalt - Prüfverfahren - Teil 2: Korngrößenverteilung This European Standard was approved by CEN on 19 March 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-2:2015 ESIST EN 12697-2:2015
EN 12697-2:2015 (E) 2 Contents Page Foreword .3 1 Scope .7 2 Normative references .7 3 Terms and definitions .7 4 Significance and use .7 5 Principle .8 6 Apparatus .8 7 Sample preparation .8 8 Procedure .8 9 Calculation .9 10 Report .9 11 Precision .9 Bibliography . 11
SIST EN 12697-2:2015
EN 12697-2:2015 (E) 3 Foreword This document (EN 12697-2:2015) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2015 and conflicting national standards shall be withdrawn at the latest by October 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12697-2:2002+A1:2007. The following is a list of changes since the previous edition: — the series title no longer makes the method exclusively for hot mix asphalt; — clarification of what defines constant mass to be consistent with EN 933-1; — limit size of sample to less than 1 kg; — clarification of procedure when washing the aggregate is required. This European Standard is one of a series of standards as follows: — EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content — EN 12697-2, Bituminous mixtures — Test methods — Part 2: Determination of particle size distribution — EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator — EN 12697-4, Bituminous mixtures — Test methods — Part 4: Bitumen recovery: Fractionating column — EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density — EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens — EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays — EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void characteristics of bituminous specimens — EN 12697-10, Bituminous mixtures —Test methods for hot mix asphalt — Part 10: Compactability — EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen — EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens SIST EN 12697-2:2015
EN 12697-2:2015 (E) 4 — EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement — EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content — EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity — EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres — EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous asphalt specimen — EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage — EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen — EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or cylindrical specimens (CY) — EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens — EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking — EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens — EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue — EN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test — EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness — EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling — EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading — EN 12697-29, Bituminous mixtures — Test method for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen — EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor — EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor — EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor — EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared by roller compactor SIST EN 12697-2:2015
EN 12697-2:2015 (E) 5 — EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test — EN 12697-35, Bituminous mixtures —Test methods for hot mix asphalt — Part 35: Laboratory mixing — EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.