Radio-frequency connectors - Part 66: Sectional specification for RF coaxial connectors with 5 mm inner diameter of outer conductor, with quick-lock- or screw-coupling, characteristic impedance 50 Ohm (series 2,2-5) (IEC 61169-66:2021)

This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series 2,2-5 RF coaxial connectors with quick-lock- or screw coupling, characteristic impedance 50 Ω, for operating frequencies up to 6 GHz. Typical use is in wireless telecommunication systems.
It describes mating face dimensions for general purpose connectors - grade 2, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series 2,2-5 RF connectors.
This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference purpose only.

Hochfrequenz-Steckverbinder – Teil 66: Rahmenspezifikation für koaxiale HF-Steckverbinder mit 5 mm Innendurchmesser des Außenleiters, mit Schraub- oder Schnapp-Kupplung, Wellenwiderstand 50 Ohm, für den Einsatz bis zu 6 GHz – Typ 2.2-5 (IEC 61169-66:2021)

Connecteurs pour fréquences radioélectriques - Partie 66 : Spécification intermédiaire relative aux connecteurs coaxiaux pour fréquences radioélectriques avec diamètre intérieur du conducteur extérieur de 5 mm à couplage à verrouillage rapide ou à vis, impédance caractéristique de 50 Ω (série 2,2-5) (IEC 61169-66:2021)

IEC 61169-66:2021 fournit des informations et des règles en vue de l’établissement de spécifications particulières (SP) pour des connecteurs coaxiaux pour fréquences radioélectriques à couplage de type à vis ou à verrouillage rapide de la série 2,2-5, avec impédance caractéristique de 50 Ω, de fréquence de fonctionnement allant jusqu’à 6 GHz. L’utilisation type est celle dans les systèmes de télécommunication sans fil. Elle décrit les dimensions des faces d’accouplement pour des connecteurs généraux de classe 2, ainsi que des informations concernant les calibres et les essais choisis dans l’IEC 61169-1, applicables à toutes les spécifications particulières ayant trait aux connecteurs pour fréquences radioélectriques de la série 2,2-5. La présente spécification indique les caractéristiques de performance recommandées à prendre en considération pour rédiger une spécification particulière, et elle couvre les programmes d'essai et les exigences de contrôle pour les niveaux d'assurance qualité M et H.

Radiofrekvenčni konektorji - 66. del: Področna specifikacija za radiofrekvenčne (RF) koaksialne konektorje z notranjim premerom zunanjih vodnikov 5 mm z zaklepno ali vijačno sklopko, karakteristična impedanca 50 Ohm (serija 2,2-5) (IEC 61169-66:2021)

General Information

Status
Published
Publication Date
28-Apr-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Apr-2021
Due Date
19-Jun-2021
Completion Date
29-Apr-2021

Buy Standard

Standard
EN IEC 61169-66:2021
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61169-66:2021
01-junij-2021
Radiofrekvenčni konektorji - 66. del: Področna specifikacija za radiofrekvenčne
(RF) koaksialne konektorje z notranjim premerom zunanjih vodnikov 5 mm z
zaklepno ali vijačno sklopko, karakteristična impedanca 50 Ohm (serija 2,2-5) (IEC
61169-66:2021)
Radio-frequency connectors - Part 66: Sectional specification for RF coaxial connectors
with 5 mm inner diameter of outer conductor, with quick-lock- or screw-coupling,
characteristic impedance 50 Ohm (series 2,2-5) (IEC 61169-66:2021)
Hochfrequenz-Steckverbinder – Teil 66: Rahmenspezifikation für koaxiale HF-
Steckverbinder mit 5 mm Innendurchmesser des Außenleiters, mit Schraub- oder
Schnapp-Kupplung, Wellenwiderstand 50 Ohm, für den Einsatz bis zu 6 GHz – Typ 2.2-5
(IEC 61169-66:2021)
Connecteurs pour fréquences radioélectriques - Partie 66 : Spécification intermédiaire
relative aux connecteurs coaxiaux pour fréquences radioélectriques avec diamètre
intérieur du conducteur extérieur de 5 mm à couplage à verrouillage rapide ou à vis,
impédance caractéristique de 50 Ω (série 2,2-5) (IEC 61169-66:2021)
Ta slovenski standard je istoveten z: EN IEC 61169-66:2021
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 61169-66:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61169-66:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 61169-66:2021


EUROPEAN STANDARD EN IEC 61169-66

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2021
ICS 33.120.30

English Version
Radio-frequency connectors - Part 66: Sectional specification for
RF coaxial connectors with 5 mm inner diameter of outer
conductor, with quick-lock- or screw-coupling, characteristic
impedance 50 O (series 2,2-5)
(IEC 61169-66:2021)
Connecteurs pour fréquences radioélectriques - Partie 66: Hochfrequenz-Steckverbinder - Teil 66:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxiale HF-Steckverbinder mit 5
coaxiaux pour fréquences radioélectriques avec diamètre mm Innendurchmesser des Außenleiters, mit Schraub- oder
intérieur du conducteur extérieur de 5 mm à couplage à Schnellverriegelungs-Kupplung, Wellenwiderstand 50 Ohm
verrouillage rapide ou à vis, impédance caractéristique de (Reihe 2.2-5)
50 O (série 2,2-5) (IEC 61169-66:2021)
(IEC 61169-66:2021)
This European Standard was approved by CENELEC on 2021-03-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61169-66:2021 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61169-66:2021
EN IEC 61169-66:2021 (E)
European foreword
The text of document 46F/543/FDIS, future edition 1 of IEC 61169-66, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-66:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-12-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-03-30
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61169-66:2021 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 61169-66:2021
EN IEC 61169-66:2021 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1: Generic EN 61169-1 2013
specification - General requirements and
measuring methods
IEC 62037-1 2012 Passive RF and microwave devices, EN 62037-1 2012
intermodulation level measurement - Part 1:
General requirements and measuring
methods

3

---------------------- Page: 5 ----------------------
SIST EN IEC 61169-66:2021

---------------------- Page: 6 ----------------------
SIST EN IEC 61169-66:2021



IEC 61169-66

®


Edition 1.0 2021-02




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Radio-frequency connectors –

Part 66: Sectional specification for RF coaxial connectors with 5 mm inner

diameter of outer conductor, with quick-lock- or screw-coupling, characteristic

impedance 50 Ω (series 2,2-5)



Connecteurs pour fréquences radioélectriques –


Partie 66: Spécification intermédiaire relative aux connecteurs coaxiaux pour

fréquences radioélectriques avec diamètre intérieur du conducteur extérieur de

5 mm à couplage à verrouillage rapide ou à vis, impédance caractéristique de


50 Ω (série 2,2-5)









INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.30 ISBN 978-2-8322-9468-0




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61169-66:2021
– 2 – IEC 61169-66:2021 © IEC 2021
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Mating face and gauge information . 8
4.1 Dimensions – General purpose connectors – Grade 2 . 8
4.1.1 Connector with pin centre contact . 8
4.1.2 Connector with socket centre contact . 9
4.2 Presentation of possible coupling mechanisms . 11
4.2.1 Screw type (see Figure 3) . 11
4.2.2 Hand screw type (see Figure 4) . 12
4.2.3 Quick lock type (see Figure 5) . 12
4.3 Gauges . 13
4.3.1 Gauge pins for socket-centre contact (see Figure 6) . 13
4.3.2 Gauge rings for socket outer contact (see Figure 7) . 14
4.4 Dimensions – Standard test connectors – Grade 0 . 14
4.4.1 Connector with pin centre contact . 14
4.4.2 Connector with socket centre contact . 16
5 Quality assessment procedures . 17
5.1 General . 17
5.2 Ratings and characteristics . 17
5.3 Test schedule and inspection requirements. 20
5.3.1 Acceptance tests . 20
5.3.2 Periodic tests . 20
5.4 Procedures for quality conformance . 22
5.4.1 Quality conformance inspection . 22
5.4.2 Qualification approval and its maintenance . 22
5.5 Test and measurement procedures . 22
5.5.1 General . 22
5.5.2 Schedule of basic test groupings for acceptance and periodic tests . 22
6 Specifications . 23
6.1 Specification structures . 23
6.1.1 Sectional specification (SS) . 23
6.1.2 Detail specification (DS) . 23
6.1.3 Blank detail specification (BDS) . 23
6.1.4 Blank detail specification pro-forma for 50 Ω type 2,2-5 connector . 25
7 Marking . 29
7.1 Marking of component . 29
7.2 Marking and contents of package . 30

Figure 1 – Connector with pin centre contact . 8
Figure 2 – Connector with socket centre contact . 10
Figure 3 – Screw type connector . 11
Figure 4 – Hand-screw type connector . 12

---------------------- Page: 8 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 3 –
Figure 5 – Quick lock type connector . 12
Figure 6 – Gauge pins for socket-centre contact (for dimensions, see Table 3) . 13
Figure 7 – Gauge rings for socket outer contact (for dimensions, see Table 4) . 14
Figure 8 – Connector with pin centre contact – Grade 0 . 15
Figure 9 – Connector with socket centre contact – Grade 0 . 16

Table 1 – Dimensions of connector with pin centre contact – Grade 2 . 9
Table 2 – Dimensions of connector with socket centre contact – Grade 2 . 10
Table 3 – Dimensions of gauge pins for socket-centre contact . 13
Table 4 – Dimensions of gauge rings for socket outer contact . 14
Table 5 – Dimensions of connector with pin centre contact – Grade 0 . 15
Table 6 – Dimensions of connector with socket centre contact – Grade 0 . 17
Table 7 – Climatic categories . 18
Table 8 – Ratings and characteristics . 18
Table 9 – Acceptance tests . 20
Table 10 – Periodic tests . 21

---------------------- Page: 9 ----------------------
SIST EN IEC 61169-66:2021
– 4 – IEC 61169-66:2021 © IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 66: Sectional specification for RF coaxial connectors with 5 mm inner
diameter of outer conductor, with quick-lock- or screw-coupling,
characteristic impedance 50 Ω (series 2,2-5)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61169-66 has been prepared by subcommittee 46F: RF and microwave passive
components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF
and microwave passive components and accessories. It is an International Standard.
The text of this International Standard is based on the following documents:
FDIS Report on voting
46F/543/FDIS 46F/552/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

---------------------- Page: 10 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 5 –
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts of the IEC 61169 series, under the general title Radio-frequency connectors,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------
SIST EN IEC 61169-66:2021
– 6 – IEC 61169-66:2021 © IEC 2021
INTRODUCTION
The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed
that compliance with this document may involve the use of a patent. IEC takes no position
concerning the evidence, validity, and scope of this patent right.
The holder of this patent right has assured IEC that s/he is willing to negotiate licences under
reasonable and non-discriminatory terms and conditions with applicants throughout the world.
In this respect, the statement of the holder of this patent right is registered with IEC. Information
may be obtained from the patent database available at http://patents.iec.ch.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights other than those in the patent database. IEC shall not be held
responsible for identifying any or all such patent rights.

---------------------- Page: 12 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 7 –
RADIO-FREQUENCY CONNECTORS –

Part 66: Sectional specification for RF coaxial connectors with 5 mm inner
diameter of outer conductor, with quick-lock- or screw-coupling,
characteristic impedance 50 Ω (series 2,2-5)



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for series 2,2-5 RF coaxial connectors with
quick-lock- or screw coupling, characteristic impedance 50 Ω, for operating frequencies up to
6 GHz. Typical use is in wireless telecommunication systems.
It describes mating face dimensions for general purpose connectors – grade 2, gauging
information and tests selected from IEC 61169-1, applicable to all detail specifications relating
to series 2,2-5 RF connectors.
This specification indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference
purpose only.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 62037-1:2012, Passive RF and microwave devices, intermodulation level measurement –
Part 1: General requirements and measuring methods
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp

---------------------- Page: 13 ----------------------
SIST EN IEC 61169-66:2021
– 8 – IEC 61169-66:2021 © IEC 2021
4 Mating face and gauge information
4.1 Dimensions – General purpose connectors – Grade 2
4.1.1 Connector with pin centre contact
The mating face of connector with pin centre contact is shown in Figure 1 and its dimensions
are shown in Table 1.

Figure 1 – Connector with pin centre contact

---------------------- Page: 14 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 9 –
Table 1 – Dimensions of connector with pin centre contact – Grade 2
mm Remarks
Ref.
Min. Max.
a 8,30 8,50
b 7,50 8,00 See Note 1
c 4,00 5,00
d -- 6,20
e 4,40 --
f -- 2,90 See Note 2
g 1,32 1,37
h 6,67 6,72
i 9,98 10,02
j M14x1 – tolerance 6H thread
k 5,0 nominal for Z = 50 Ω
l -- 19,50
m -- 2,50
n 2,2 nominal -- for Z = 50 Ω
o -- 0,70
p 7,50 8,00
q 20° nominal
r 0,50 nominal radius
NOTE 1 Minimum dimension only for screw coupling types.
NOTE 2 Applicable for inner and outer contact.

4.1.2 Connector with socket centre contact
The mating face of connector with socket centre contact is shown in Figure 2 and its dimensions
are shown in Table 2.

---------------------- Page: 15 ----------------------
SIST EN IEC 61169-66:2021
– 10 – IEC 61169-66:2021 © IEC 2021

Figure 2 – Connector with socket centre contact
Table 2 – Dimensions of connector with socket centre contact – Grade 2
mm
Ref. Remarks
Min. Max.
a 9,00 --
b 8,50 --
c 1,70 1,90
d 1,44 1,50
e 3,10 3,35 See Note 1
f 3,50 --
g 8,50 --
h 5,0 nominal for Z = 50 Ω
i 10,05 10,10
j 11,45 11,55
k 12,45 12,55
l M14x1 tolerance 6g thread
m 2,2 nominal for Z = 50 Ω
n 10,65 10,75
o -- 7,5 See Notes 2 and 3
p  See Note 3
q 12,05 12,15
r 25° nominal

---------------------- Page: 16 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 11 –
mm
Ref. Remarks
Min. Max.
s 45° nominal
t 1,0 nominal radius
u 1,0 nominal radius
NOTE 1 Applicable for inner and outer contact.
NOTE 2 In unmated condition.
NOTE 3 Resilient to meet gauging requirements.

4.2 Presentation of possible coupling mechanisms
4.2.1 Screw type (see Figure 3)
Dimensions in millimetres

Figure 3 – Screw type connector

---------------------- Page: 17 ----------------------
SIST EN IEC 61169-66:2021
– 12 – IEC 61169-66:2021 © IEC 2021
4.2.2 Hand screw type (see Figure 4)
Dimensions in millimetres

Figure 4 – Hand-screw type connector
4.2.3 Quick lock type (see Figure 5)
Dimensions in millimetres

Figure 5 – Quick lock type connector

---------------------- Page: 18 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 13 –
4.3 Gauges
4.3.1 Gauge pins for socket-centre contact (see Figure 6)
Dimensions in millimetres

Figure 6 – Gauge pins for socket-centre contact
(for dimensions, see Table 3)
Table 3 – Dimensions of gauge pins for socket-centre contact
Gauge A Gauge B
Ref mm mm
Min. Max. Min. Max.
a
0,67 0,73 0,67 0,73
b 1,370 1,377 1,313 1,320
c 3,3 3,5 3,3 3,5
d 44° 46° 36° 44°
Material: steel, polished, surface roughness: Ra = 0,4 µm maximum.

Test procedure:
The gauge A shall be completely inserted three times into the socket centre contact. This is a
sizing operation.
After sizing, gauge A shall be inserted into socket centre contact. The insertion force shall not
exceed 10 N.
Separation force is measured with gauge B and shall require a minimum force of 0,8 N.

---------------------- Page: 19 ----------------------
SIST EN IEC 61169-66:2021
– 14 – IEC 61169-66:2021 © IEC 2021
4.3.2 Gauge rings for socket outer contact (see Figure 7)
Dimensions in millimetres

Figure 7 – Gauge rings for socket outer contact (for dimensions, see Table 4)
Table 4 – Dimensions of gauge rings for socket outer contact
Gauge A Gauge B
Ref
Min. Max. Min. Max.
a 7,5 7,7 7,5 7,7
b 6,663 6,670 6,720 6,727
c 8,3 8,5 8,3 8,5
d 9,92 9,96 – 9,7
e 11° 12° 10° 15°
Material: steel, polished, surface roughness: Ra = 0,4 µm maximum.

Test procedure:
The gauge A shall be completely inserted three times into the resilient outer contact. This is a
sizing operation.
After sizing, gauge A shall be inserted into the resilient contact. The insertion force shall not
exceed 22 N.
Separation force is measured with gauge B and shall require a minimum force of 2,5 N. All
contact segments shall touch the diameter b in the region of the tips.
4.4 Dimensions – Standard test connectors – Grade 0
4.4.1 Connector with pin centre contact
The mating face of connector with pin centre contact is shown in Figure 8 and its dimensions
are shown in Table 5.

---------------------- Page: 20 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 15 –

Figure 8 – Connector with pin centre contact – Grade 0
Table 5 – Dimensions of connector with pin centre contact – Grade 0
mm
Ref. Remarks
Min. Max.
a 8,30 8,50
b 7,50 8,00 1
c 4,00 5,00
d -- 6,20
e 4,40 --
f 2,84 2,90 2
g 1,34 1,35
h 6,688 6,702
i 10,00 10,02
j M14x1 – tolerance 6H thread
k 5,0 nominal for Z = 50 Ω
l -- 19,50
m -- 2,50
n 2,2 nominal -- for Z = 50 Ω
o -- 0,70

---------------------- Page: 21 ----------------------
SIST EN IEC 61169-66:2021
– 16 – IEC 61169-66:2021 © IEC 2021
mm
Ref. Remarks
Min. Max.
p 7,50 8,00
q 20° nominal
r 0,50 nominal radius
NOTE 1 Minimum dimension only for screw coupling types.
NOTE 2 Applicable for inner and outer contact.

4.4.2 Connector with socket centre contact
The mating face of connector with socket centre contact is shown in Figure 9 and its dimensions
are shown in Table 6.

Figure 9 – Connector with socket centre contact – Grade 0

---------------------- Page: 22 ----------------------
SIST EN IEC 61169-66:2021
IEC 61169-66:2021 © IEC 2021 – 17 –
Table 6 – Dimensions of connector with socket centre contact – Grade 0
mm
Ref. Remarks
Min. Max.
a 9,00 --
b 8,50 --
c 1,70 1,90
d 1,44 1,50
e 3,10 3,16 See Note 1
f 3,50 --
g 8,50 --
h 5,0 nominal for Z = 50 Ω
i 10,05 10,07
j 11,45 11,55
k 12,45 12,55
l M14x1 tolerance 6g thread
m 2,2 nominal for Z = 50 Ω
n 10,65 10,75
o -- 7,5 See Notes 2 and 3
p  See Note 3
q 12,05 12,15
r 25° nominal
s 45° nominal
t 1,0 nominal radius
u 1,0 nominal radius
NOTE 1 Applicable for inner and outer contact.
NOTE 2 In unmated condition.
NOTE 3 Resilient to meet gauging requirements.

5 Quality assessment procedures
5.1 General
Subclauses 5.2 to 5.4 provide recommended ratings, performance and test conditions to be
considered when writing a detail specification (DS). They also provide an appropriate schedule
of tests with minimum levels of conformance.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.