SIST EN ISO 10426-3:2019

Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2019)

This document provides procedures for testing well cements and cement blends for use in the petroleum and natural gas industries in a deepwater environment, or areas with a low seafloor temperature, or areas where low well temperatures exist.
This document supplements API RP 10B-3, 2nd edition (2016), the requirements of which are applicable with the exceptions specified in this document.
This document excludes the mitigation of shallow water flow in deepwater wells.
NOTE       This is addressed in API RP 65.

Erdöl- und Erdgasindustrie - Zemente und Materialien für die Zementation von Tiefbohrungen - Teil 3: Prüfung von Unterwasser-Bohrlochzement (ISO 10426-3:2019)

Industries du pétrole et du gaz naturel - Ciments et matériaux pour la cimentation des puits - Partie 3: Essais de formulations de ciment pour puits en eau profonde (ISO 10426-3:2019)

Le présent document fournit des modes opératoires pour tester les ciments de puits et les mélanges de ciments utilisés dans les industries du pétrole et du gaz naturel en eaux profondes, ou dans des zones où la température du fond marin est basse, ou dans des zones où la température des puits est basse.
Ce document complète l’API RP 10B-3, 2nd edition (2016), dont les exigences sont applicables avec les exceptions spécifiées dans le présent document.
Ce document exclut l'atténuation de l'écoulement des eaux peu profondes dans les puits en eaux profondes.
NOTE          Cette question est abordée dans l'API RP 65.

Industrija za predelavo nafte in zemeljskega plina - Cementi in materiali za cementiranje vrtin - 3. del: Preskušanje sestave cementov za globokomorske vrtine (ISO 10426-3:2019)

Ta dokument določa postopke za preskušanje cementov za vrtine in cementnih mešanic za uporabo v industriji za predelavo nafte in zemeljskega plina v globokomorskem okolju ali na območjih z nizko temperaturo morskega dna oziroma območjih, kjer je prisotna nizka temperatura vrtine. Ta dokument dopolnjuje 2. izdajo standarda API RP 10B-3 (2016), katerega zahteve se uporabljajo za izjeme, določene v tem dokumentu. Ta dokument ne vključuje ublažitve toka plitke vode v globokomorskih vrtinah.

General Information

• Status: Published
• Public Enquiry End Date: 31-Mar-2018
• Publication Date: 20-Oct-2019
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 11-Oct-2019
• Due Date: 16-Dec-2019
• Completion Date: 21-Oct-2019
• Ref Project: EN ISO 10426-3:2019 - Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2019)

Relations

• Replaces: SIST EN ISO 10426-3:2005 - Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2003)
• Effective Date: 09-Oct-2019
• Revised: SIST EN ISO 10426-3:2005 - Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2003)
• Effective Date: 04-Oct-2017

Overview

EN ISO 10426-3:2019 - Petroleum and natural gas industries: Cements and materials for well cementing - Part 3 - provides standardized laboratory and simulation procedures for testing deepwater well cement formulations. It covers evaluation methods for well cements and cement blends intended for environments with water depths greater than 600 m, low seafloor temperatures, or otherwise low well temperatures. The document is an EN-adopted version of ISO 10426-3:2019 and supplements API RP 10B-3 (2nd edition, 2016), noting specific exceptions and additions.

Key topics

• Scope: Procedures focus on deepwater/low-temperature conditions and exclude mitigation of shallow water flow (see API RP 65).
• Test methods: Guidance on compressive strength (destructive) and sonic strength measurement procedures and reporting.
• Thickening time: Detailed thickening-time schedule determination, including tests for:
  • casing or liner without liner-top packer/non-expandable liner hanger
  • liner installations with liner-top packers or expandable liner hangers
  • open-hole or closed-hole plugs
  • continuous- and hesitating-pumping squeeze cementing
• Numerical pressure and temperature simulation: Added guidance to model realistic downhole temperature/pressure histories prior to laboratory testing.
• Location-specific strength evaluation: Separate treatment for strength determination at casing shoe, mudline, top-of-liner, potential flow zones, and plug/squeeze locations.
• Laboratory procedures: Expanded laboratory protocols for both sonic and destructive strength testing consistent with ISO and referenced ASTM methods where applicable.
• Units and terminology: Includes international and (where practical) United States customary units; aligns terms with API RP 10B-3.

Applications and users

Who benefits from EN ISO 10426-3:2019:

• Well cementing engineers designing deepwater cement jobs
• Laboratory technicians validating cement formulations for low-temperature environments
• Oil & gas operators and service companies performing liner/casing cementing and squeeze operations
• R&D teams developing foamed, ductile, or class A/C/G/H cements for deepwater use
• Regulators and standards bodies assessing conformity and best practices

Practical uses:

• Simulating downhole thermal histories to choose robust cement slurries
• Determining safe operational thickening times for pumping and placement
• Verifying compressive and sonic strength development at critical depths and features
• Supporting documentation for project risk assessment and cementing program approval

Related standards

• API RP 10B-3 (2nd ed., 2016) - referenced and supplemented
• API RP 65 - mitigation of shallow water flow (excluded topic)
• ISO 10426 series (other parts) - for broader well cementing materials guidance

Keywords: EN ISO 10426-3:2019, deepwater well cement testing, thickening time, compressive strength, sonic testing, API RP 10B-3, well cement formulations.

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2019
Nadomešča:
SIST EN ISO 10426-3:2005
Industrija za predelavo nafte in zemeljskega plina - Cementi in materiali za
cementiranje vrtin - 3. del: Preskušanje sestave cementov za globokomorske
vrtine (ISO 10426-3:2019)
Petroleum and natural gas industries - Cements and materials for well cementing - Part
3: Testing of deepwater well cement formulations (ISO 10426-3:2019)
Erdöl- und Erdgasindustrie - Zemente und Materialien für die Zementation von
Tiefbohrungen - Teil 3: Prüfung von Unterwasser-Bohrlochzement (ISO 10426-3:2019)
Industries du pétrole et du gaz naturel - Ciments et matériaux pour la cimentation des
puits - Partie 3: Essais de formulations de ciment pour puits en eau profonde (ISO 10426
-3:2019)
Ta slovenski standard je istoveten z: EN ISO 10426-3:2019
ICS:
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10426-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 75.020; 91.100.10 Supersedes EN ISO 10426-3:2004
English Version
Petroleum and natural gas industries - Cements and
materials for well cementing - Part 3: Testing of deepwater
well cement formulations (ISO 10426-3:2019)
Industries du pétrole et du gaz naturel - Ciments et Erdöl- und Erdgasindustrie - Zemente und Materialien
matériaux pour la cimentation des puits - Partie 3: für die Zementation von Tiefbohrungen - Teil 3:
Essais de formulations de ciment pour puits en eau Prüfung von Unterwasser-Bohrlochzement (ISO
profonde (ISO 10426-3:2019) 10426-3:2019)
This European Standard was approved by CEN on 9 June 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10426-3:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 10426-3:2019) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries"
in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10426-3:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 10426-3:2019 has been approved by CEN as EN ISO 10426-3:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 10426-3
Second edition
2019-08
Petroleum and natural gas
industries — Cements and materials
for well cementing —
Part 3:
Testing of deepwater well cement
formulations
Industries du pétrole et du gaz naturel — Ciments et matériaux pour
la cimentation des puits —
Partie 3: Essais de formulations de ciment pour puits en eau profonde
Reference number
ISO 10426-3:2019(E)
©
ISO 2019
ISO 10426-3:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 10426-3:2019(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
nd
4 Supplements to API RP 10B-3, 2 edition (2016) . 2
4.1 General requirements . 2
4.2 Procedure for compressive strength determination . 2
4.3 Thickening-time schedule determination . 2
4.3.1 Testing method and procedures for a casing or liner without a liner-top
packer or non-expandable liner hanger system . 2
4.3.2 Testing method for a liner with a liner-top packer or expandable liner
hanger system . 2
4.3.3 Testing method for open-hole or closed-hole plug . 2
4.3.4 Thickening-time test procedure . 2
4.3.5 Testing method for continuous-pumping squeeze cementing . 3
4.3.6 Testing method for hesitating-pumping squeeze cementing . 3
Bibliography . 4
ISO 10426-3:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment,
...