SIST EN 4630:2015
(Main)Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Hardened and tempered - Forgings - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted - Hardened and tempered - Forgings - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
This standard specifies the requirements relating to:
Steel X4CrNiMo16-5-1 (1.4418)
Air melted
Hardened and tempered
Forgings
De ≤ 200 mm
900 MPa ≤ Rm ≤ 1 050 MPa
for aerospace applications.
NOTE Other common designation: AIR: Z 8 CND 17-04.
Luft- und Raumfahrt - Stahl X4CrNiMo16-5-1 (1.4418) - Lufterschmolzen - Gehärtet- und angelassen - Schmiedestücke - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Série aérospatiale - Acier X4CrNiMo16-5-1 (1.4418) - Élaboré à l'air - Trempé et revenu - Pièces forgées - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Aeronavtika - Jeklo X4CrNiMo16-5-1 (1.4418) - Taljeno - Utrjeno in mehko žarjeno - Izkovki - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Ta standard določa zahteve glede:
jekla X4CrNiMo16-5-1 (1.4418),
taljenega,
utrjenega in mehko žarjenega,
izkovki,
De ≤ 200 mm,
900 MPa ≤ Rm ≤ 1050 MPa,
za uporabo v aeronavtiki.
OPOMBA: Druga pogosta oznaka: AIR: Z 8 CND 17-04.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.03D49.025.10JeklaSteelsICS:Ta slovenski standard je istoveten z:EN 4630:2014SIST EN 4630:2015en,fr,de01-januar-2015SIST EN 4630:2015SLOVENSKI
STANDARDSIST EN 4630:20081DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4630
October 2014 ICS 49.025.10 Supersedes EN 4630:2007English Version
Aerospace series - Steel X4CrNiMo16-5-1 (1.4418) - Air melted -Hardened and tempered - Forgings - De ≤ 200 mm - 900 MPa ≤Rm ≤ 1 050 MPa
Série aérospatiale - Acier X4CrNiMo16-5-1 (1.4418) - Élaboré à l'air - Trempé et revenu - Pièces forgées - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Luft- und Raumfahrt - Stahl X4CrNiMo16-5-1 (1.4418) - Lufterschmolzen - Gehärtet- und angelassen - Schmiedestücke - De ≤ 200 mm - 900 MPa ≤ Rm ≤ 1 050 MPa This European Standard was approved by CEN on 27 December 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4630:2014 ESIST EN 4630:2015
Page Foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.