oSIST prEN 50131-3:2025

Alarm systems - Intrusion and hold-up systems - Part 3: Control and indicating equipment

This document specifies the requirements, performance criteria and testing procedures for control and indicating equipment (CIE) intended for use in intrusion and hold-up alarm systems (I&HAS) installed in buildings. This document also applies to CIE to be used in IAS or HAS.
The CIE can incorporate processing functions of other I&HAS components or its processing requirements can be distributed among such components.
This document specifies the requirements for CIE installed in buildings using specific or non-specific wired interconnections or wire-free interconnections. These requirements also apply to basic DCC which can be installed outside of the supervised premises and mounted in indoor or outdoor environments.
Where CIE shares means of detection, interconnection, control, communication, processing and/or power supplies with other applications, these requirements apply to I&HAS functions only.
This document specifies performance requirements for CIE at each of the four security grades identified in EN 50131 1. Requirements are also specified for four environmental classes covering applications for indoor and outdoor locations.
This document includes mandatory functions for all CIE for the appropriate security grade, as well as optional functions that can additionally be provided.
This document does not cover requirements for compliance with EU regulatory Directives, such as the EMC Directive, Low Voltage Directive, etc. except in that it specifies the equipment operating conditions for EMC susceptibility testing as required by EN 50130 4.
NOTE 1   In this document reference to the term “I&HAS” is used throughout, except where there is specific need to differentiate between the IAS and HAS portions of a system. The term is intended to include IAS and HAS when such systems are installed separately.
NOTE 2   For products which integrate functions from, and which the manufacturer is claiming compliance to, several EN 50131 standards, the requirements of this document apply as well as any additional requirements from other relevant EN 50131 standards (e.g. a CIE with integral Warning Device is expected to meet the requirements of EN 50131 3 and EN 50131 4).

Alarmanlagen - Einbruch- und Überfallmeldeanlagen - Teil 3: Befehls- und Meldegeräte

Systèmes d’alarme - Systèmes d’alarme contre l’intrusion et les hold-up - Partie 3: Équipement de contrôle et de signalisation

Le présent document spécifie les exigences, les critères de performance et les procédures d’essai pour les équipements de contrôle et de signalisation (CIE) destinés à être utilisés dans les systèmes d’alarme contre l’intrusion et les hold-up (I&HAS) installés dans les bâtiments. Le présent document s’applique également aux CIE destinés à être utilisés dans les systèmes IAS ou HAS.
Les CIE peuvent incorporer des fonctions de traitement d’autres composants I&HAS ou leurs besoins de traitement peuvent être répartis entre ces composants.
Le présent document spécifie les exigences relatives aux CIE installés dans des bâtiments qui utilisent des liaisons filaires spécifiques ou non spécifiques ou des liaisons radio. Ces exigences s’appliquent également aux DCC de base qui peuvent être installés à l’extérieur des bâtiments surveillés et montés dans un environnement intérieur ou extérieur.
Lorsque le CIE partage des moyens de détection, de liaison, de commande, de communication, de traitement et/ou des alimentations avec d’autres applications, ces exigences ne s’appliquent qu’aux fonctions I&HAS.
Le présent document spécifie les exigences de performance applicables aux CIE à chacun des quatre grades de sécurité identifiés dans l’EN 50131 1. Des exigences sont également spécifiées pour quatre classes d’environnement couvrant des applications pour des emplacements intérieurs et extérieurs.
Le présent document inclut des fonctions obligatoires pour tous les CIE pour le grade approprié de sécurité, ainsi que des fonctions facultatives complémentaires.
Le présent document ne couvre pas les exigences de conformité aux directives réglementaires de l’UE, telles que la Directive CEM, la Directive basse tension, etc., mais il spécifie les conditions de fonctionnement des équipements pour les essais de susceptibilité CEM, comme cela est exigé par l’EN 50130 4.
NOTE 1   Dans la totalité du présent document, il est fait référence au terme “I&HAS”, sauf lorsqu’il est spécifiquement nécessaire de différencier les parties IAS et HAS d’un système. Ce terme est destiné à inclure les systèmes IAS et HAS lorsque ces systèmes sont installés séparément.
NOTE 2   Pour les produits qui intègrent des fonctions relatives, et pour lesquels le fabricant revendique la conformité, à plusieurs normes EN 50131, les exigences du présent document s’appliquent ainsi que toutes les exigences supplémentaires des autres normes EN 50131 pertinentes (par exemple, il est attendu qu’un CIE équipé d’un dispositif d’avertissement interne respectent les exigences de l’EN 50131 3 et de l’EN 50131 4).

Alarmni sistemi - Sistemi za javljanje vloma in ropa - 3. del: Kontrolna in indikacijska oprema

General Information

• Status: Not Published
• Public Enquiry End Date: 30-Jul-2025
• ICS: 13.310 - Protection against crime
• ICS: 13.320 - Alarm and warning systems
• Technical Committee: EAL - Alarm systems
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 29-May-2025
• Due Date: 16-Oct-2025
• Ref Project: prEN 50131-3:2025 - Alarm systems - Intrusion and hold-up systems - Part 3: Control and indicating equipment

Relations

• Revises: SIST EN 50131-3:2009 - Alarm systems - Intrusion and hold-up systems -- Part 3: Control and indicating equipment
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2025
Alarmni sistemi - Sistemi za javljanje vloma in ropa - 3. del: Kontrolna in
indikacijska oprema
Alarm systems - Intrusion and hold-up systems - Part 3: Control and indicating
equipment
Alarmanlagen - Einbruch- und Überfallmeldeanlagen - Teil 3: Befehls- und Meldegeräte
Systèmes d’alarme - Systèmes d’alarme contre l’intrusion et les hold-up - Partie 3:
Équipement de contrôle et de signalisation
Ta slovenski standard je istoveten z: prEN 50131-3:2025
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD DRAFT
prEN 50131-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2025
ICS 13.320 Will supersede EN 50131-3:2009; EN 50131-
3:2009/corrigendum Dec. 2010
English Version
Alarm systems - Intrusion and hold-up systems - Part 3: Control
and indicating equipment
To be completed Alarmanlagen - Einbruch- und Überfallmeldeanlagen - Teil
3: Befehls- und Meldegeräte
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2025-08-15.

It has been drawn up by CLC/TC 79.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 76130 Ref. No. prEN 50131-3:2025 E

Contents Page
1 European foreword . 5
2 Introduction . 6
3 1 Scope . 7
4 2 Normative references . 7
5 3 Terms, definitions and abbreviations . 8
6 3.1 Terms and definitions . 8
7 3.2 Abbreviations .11
8 4 Equipment attributes .12
9 4.1 General .12
10 4.2 Functionality .12
11 5 CIE topology .12
12 6 Security grade .13
13 7 Environmental performance .13
14 7.1 Requirements .13
15 7.2 Environmental and EMC tests .13
16 8 Functional requirements .13
17 8.1 Inputs .13
18 8.1.1 Intruder detection .13
19 8.1.2 Hold-up device .13
20 8.1.3 Tamper .13
21 8.1.4 Fault .13
22 8.1.5 User input .14
23 8.1.6 Masking .14
24 8.1.7 Non-I&HAS inputs .14
25 8.2 Outputs .14
26 8.3 Operation .15
27 8.3.1 Access levels .15
28 8.3.2 Authorization .15
29 8.3.3 Setting procedures .18
30 8.3.4 Unsetting procedure .18
31 8.3.5 Restore function .19
32 8.3.6 Inhibit function .19
33 8.3.7 Isolate operation .19
34 8.3.8 Verification of I&HAS functions .19
35 8.3.9 Soak test function .19
36 8.3.10 Other functions .19
37 8.4 Processing.20
38 8.4.1 Processing of input signals or messages .20
39 8.4.2 Processing of user inputs .20
40 8.4.3 Monitoring of CIE processing.20
41 8.5 Indication .21
42 8.5.1 General .21
43 8.5.2 Priority of indications .22
44 8.6 Notification outputs .22
45 8.6.1 Other notification .22
46 8.7 Tamper security (detection/protection) .22
47 8.7.1 Tamper protection .22
48 8.7.2 Tamper detection .23
49 8.7.3 Monitoring of substitution . 24
50 8.8 Interconnections . 24
51 8.9 Timing . 25
52 8.10 Event recording . 25
53 8.10.1 Event recording at the CIE . 25
54 8.10.2 Event recording at the ARC or other remote location . 26
55 8.11 Power supply . 26
56 9 Product documentation . 26
57 9.1 Installation and maintenance . 26
58 9.2 Operating instructions . 27
59 10 Marking and labelling . 28
60 11 Tests . 28
61 11.1 Test conditions . 28
62 11.1.1 Laboratory conditions and tolerance . 28
63 11.1.2 Mounting . 28
64 11.1.3 CIE test configuration . 29
65 11.1.4 Power supply . 29
66 11.1.5 Event log checks . 29
67 11.1.6 Documentation . 30
68 11.2 Test procedures . 30
69 11.2.1 Tolerances . 30
70 11.2.2 Wire-free devices . 30
71 11.3 Reduced functional test . 30
72 11.4 Functional tests . 31
73 11.4.1 Processing intruder alarm signals or messages . 31
74 11.4.2 Processing of hold-up signals or messages . 33
75 11.4.3 Processing of tamper signals or messages . 35
76 11.4.4 Processing of fault signals or messages. 37
77 11.4.5 Processing masking signals or messages . 39
78 11.4.6 CIE Processing in the presence of non-I&HAS inputs .
...