SIST EN ISO 11833-1:2012
(Main)Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)
Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)
This part of ISO 11833 specifies the requirements for flat extruded sheets and pressed sheets of unplasticized poly(vinyl chloride) (PVC-U) and the test methods to be used to measure the required values. It applies only to sheets of thickness not less than 1,0 mm. It does not cover biaxially stretched PVC-U sheets.
Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften - Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2012)
Dieser Teil von ISO 11833 legt die Anforderungen an flache extrudierte Tafeln und gepresste Tafeln aus weichmacherfreiem Polyvinylchlorid (PVC-U) und die zum Messen der geforderten Werte anzuwendenden Prüfverfahren fest.
Die Norm gilt nur für Tafeln mit einer Dicke von mindestens 1,0 mm.
Biaxial gereckte PVC-U-Tafeln werden nicht berücksichtigt.
Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Types, dimensions et caractéristiques - Partie 1: Plaques d'épaisseur non inférieure à 1 mm (ISO 11833-1:2012)
L'ISO 11833-1:2012 spécifie les exigences relatives aux plaques extrudées et aux plaques pressées, planes, en poly(chlorure de vinyle) non plastifié (PVC‑U), ainsi que les méthodes d'essai à utiliser pour mesurer les valeurs requises.
Elle est applicable uniquement aux plaques d'épaisseur au moins égale à 1,0 mm.
Elle ne s'applique pas aux feuilles en PVC‑U bi‑étirées.
Polimerni materiali - Nemehčane polivinilkloridne plošče - Vrste, mere in značilnosti - 1. del: Plošče z debelino več kot 1 mm (ISO 11833-1:2012)
Ta del standarda ISO 11833 določa zahteve za ploščate ekstrudirane plošče in stisnjene plošče iz nemehčanega polivinilklorida (PVC-U) ter preskusne metode, ki jih je treba uporabiti za merjenje zahtevanih vrednosti. Zadeva le plošče z debelino več kot 1 mm. Ne zajema dvoosno raztegnjenih polivinilkloridnih plošč.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11833-1:2012
01-oktober-2012
1DGRPHãþD
SIST EN ISO 11833-1:2009
3ROLPHUQLPDWHULDOL1HPHKþDQHSROLYLQLONORULGQHSORãþH9UVWHPHUHLQ
]QDþLOQRVWLGHO 3ORãþH]GHEHOLQRYHþNRWPP ,62
Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and
characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)
Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften
- Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2012)
Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Types, dimensions et
caractéristiques - Partie 1: Plaques d'épaisseur non inférieure à 1 mm (ISO 11833-
1:2012)
Ta slovenski standard je istoveten z: EN ISO 11833-1:2012
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 11833-1:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11833-1:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 11833-1:2012
EUROPEAN STANDARD
EN ISO 11833-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2012
ICS 83.140.10 Supersedes EN ISO 11833-1:2007
English Version
Plastics - Unplasticized poly(vinyl chloride) sheets - Types,
dimensions and characteristics - Part 1: Sheets of thickness not
less than 1 mm (ISO 11833-1:2012)
Plastiques - Feuilles en poly(chlorure de vinyle) non Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln -
plastifié - Types, dimensions et caractéristiques - Partie 1: Typen, Maße und Eigenschaften - Teil 1: Tafeln mit einer
Plaques d'épaisseur non inférieure à 1 mm (ISO 11833- Dicke von mindestens 1 mm (ISO 11833-1:2012)
1:2012)
This European Standard was approved by CEN on 23 June 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11833-1:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11833-1:2012
EN ISO 11833-1:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11833-1:2012
EN ISO 11833-1:2012 (E)
Foreword
This document (EN ISO 11833-1:2012) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2013, and conflicting national standards shall be withdrawn at
the latest by January 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11833-1:2007.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, the United Kingdom and Turkey.
Endorsement notice
The text of ISO 11833-1:2012 has been approved by CEN as a EN ISO 11833-1:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11833-1:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 11833-1:2012
INTERNATIONAL ISO
STANDARD 11833-1
Third edition
2012-06-01
Plastics — Unplasticized poly(vinyl
chloride) sheets — Types, dimensions
and characteristics —
Part 1:
Sheets of thickness not less than 1 mm
Plastiques — Feuilles en poly(chlorure de vinyle) non plastifié — Types,
dimensions et caractéristiques —
Partie 1: Plaques d’épaisseur non inférieure à 1 mm
Reference number
ISO 11833-1:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 11833-1:2012
ISO 11833-1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11833-1:2012
ISO 11833-1:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Material . 2
4 Classification . 2
5 Requirements . 2
5.1 Masking . 2
5.2 Appearance . 2
5.3 Colour . 2
5.4 Dimensions . 2
5.5 Basic properties . 4
5.6 Other mechanical and physical properties . 6
5.7 Chemical and physiological properties . 6
6 Test methods . 6
6.1 General . 6
6.2 Appearance examination . 7
6.3 Dimensions . 7
6.4 Mechanical properties . 7
6.5 Thermal properties . 7
6.6 Total luminous transmittance . 9
6.7 Other mechanical and physical properties .10
7 Marking .10
Annex A (informative) Determination of resistance to delamination of thick pressed sheets using
a wedge . 11
Annex B (informative) Determination of resistance to delamination of thick pressed sheets
by thermal bending .13
Bibliography .14
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11833-1:2012
ISO 11833-1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11833-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This third edition cancels and replaces the second edition (ISO 11833-1:2007), of which Table 5 (concerning
the basic properties of the sheets) and Clause 7 (concerning marking) have been technically revised.
ISO 11833 consists of the following parts, under the general title Plastics — Unplasticized poly(vinyl chloride)
sheets — Types, dimensions and characteristics:
— Part 1: Sheets of thickness not less than 1 mm
— Part 2: Sheets of thickness less than 1 mm
iv © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11833-1:2012
INTERNATIONAL STANDARD ISO 11833-1:2012(E)
Plastics — Unplasticized poly(vinyl chloride) sheets — Types,
dimensions and characteristics —
Part 1:
Sheets of thickness not less than 1 mm
1 Scope
This part of ISO 11833 specifies the requirements for flat extruded sheets and pressed sheets of unplasticized
poly(vinyl chloride) (PVC-U) and the test methods to be used to measure the required values.
It applies only to sheets of thickness not less than 1,0 mm.
It does not cover biaxially stretched PVC-U sheets.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 75-2:2004, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 306:2004, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-2, Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading
ISO 1163-1:1995, Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials —
Part 1: Designation system and basis for specifications
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient
column method
ISO 2039-1, Plastics — Determination of hardness — Part 1: Ball indentation method
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 13468-1, Plastics — Determination of the total luminous transmittance of transparent materials — Part 1:
Single-beam instrument
IEC 60093, Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
© ISO 2012 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 11833-1:2012
ISO 11833-1:2012(E)
3 Material
Sheets shall be fabricated from PVC-U compounds as defined in ISO 1163-1:1995, Subclause 1.3. Compounds
may contain additives such as stabilizers, lubricants, processing aids, impact modifiers, fillers, flame retardants
and colourants. Compounds and additives of unknown identity and composition shall not be used for the
processing of sheets.
4 Classification
Extruded and pressed sheets are each classified into the following five groups, characterized by type of sheet
as well as by the numerical values of the three most important properties, i.e. tensile stress at yield, Charpy
impact strength and Vicat softening temperature (see Table 5):
Group 1: General-purpose grade;
Group 2: Transparent grade;
Group 3:
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.