SIST EN 474-10:2007
(Main)Earth-moving machinery - Safety - Part 10: Requirements for trenchers
Earth-moving machinery - Safety - Part 10: Requirements for trenchers
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to trenchers as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006.
This part does not deal with the specific hazards related to derivative use.
This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for trenchers.
This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of trenchers.
This European Standard is not applicable to trenchers manufactured before the date of publication of this European Standard by CEN.
Erdbaumaschinen - Sicherheit - Teil 10: Anforderungen für Grabenfräser
Dieser Teil von EN 474 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf Grabenfräsen nach EN ISO 6165:2002 zutreffen, wenn sie bestimmungsgemäß verwendet werden. Die nach vernünftigem Ermessen für den Hersteller vorhersehbare Nutzung der Maschine außerhalb der bestimmungsgemäßen Verwendung ist ebenfalls berücksichtigt (siehe Abschnitt 4).
Die Anforderungen gelten ergänzend zu den allgemeinen Anforderungen des Teil 1.
Dieser Teil befasst sich nicht mit den spezifischen Gefährdungen die sich aus missbräuchlicher Nutzung ergeben.
Dieser Teil wiederholt nicht die allgemeinen Anforderungen des Teil 1, aber ergänzt oder ersetzt diese, sofern sie für den Einsatz von Grabenfräsen von Bedeutung sind.
Dieser Teil beschreibt die geeigneten technischen Maßnahmen die erforderlich sind, die Risiken die aufgrund signifikanter Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die während der Inbetriebnahme, dem Betrieb, der Instandhaltung von Grabenfräsen eintreten können zu mindern oder zu beseitigen.
Diese Europäische Norm ist nicht anzuwenden für Grabenfräsen, die vor der Veröffentlichung dieser Europäischen Norm durch CEN hergestellt wurden.
Engins de terrassement - Sécurité - Partie 10: Prescriptions applicables aux trancheuses
La présente partie du prEN 474 traite de tous les phénomenes, situations et événements dangereux significatifs relatifs aux trancheuses définies dans l’EN ISO 6165:2002, lorsqu’elles sont utilisées comme prévu ou dans des conditions de mauvais usage que le fabricant peut raisonnablement prévoir (voir l’Article 4).
Les prescriptions figurant dans la présente partie viennent en complément des prescriptions communes présentées dans la partie 1.
La présente partie ne traite pas des phénomenes dangereux spécifiques relatifs a l’utilisation dérivée.
La présente partie ne répete pas les prescriptions de la partie 1 mais en ajoute ou en remplace certaines applicables aux trancheuses.
La présente partie prescrit les mesures techniques appropriées pour éliminer ou réduire les risques dus aux phénomenes, situations et événements dangereux significatifs survenant lors de la mise en service, du fonctionnement et de la maintenance des trancheuses.
La présente Norme européenne n’est pas applicable aux trancheuses fabriquées avant la publication de la présente Norme européenne par le CEN.
Stroji za zemeljska dela - Varnost - 10. del: Zahteve za rovokopače
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Earth-moving machinery - Safety - Part 10: Requirements for trenchersþHEngins de terrassement - Sécurité - Partie 10: Prescriptions applicables aux trancheusesErdbaumaschinen - Sicherheit - Teil 10: Anforderungen für GrabenfräserTa slovenski standard je istoveten z:EN 474-10:2006SIST EN 474-10:2007en53.100Stroji za zemeljska delaEarth-moving machineryICS:SIST EN 474-10:2000/AC:2002SIST EN 474-10:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 474-10:200701-maj-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 474-10November 2006ICS 53.100Supersedes EN 474-10:1998
English VersionEarth-moving machinery - Safety - Part 10: Requirements fortrenchersEngins de terrassement - Sécurité - Partie 10: Prescriptionsapplicables aux trancheusesErdbaumaschinen - Sicherheit - Teil 10: Anforderungen fürGrabenfräserThis European Standard was approved by CEN on 17 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 474-10:2006: E
EN 474-10:2006 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.6 4 List of additional significant hazards.6 5 Safety requirements and/or measures.6 6 Information for use.9 Annex A (normative)
List of additional significant hazards – Trenchers.10 Annex B (informative)
Illustrations.11 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC.13 Bibliography.14
Figures Figure B.1 — Wheel trencher (ride on).11 Figure B.2 — Wheel trencher (pedestrian controlled).11 Figure B.3 — Crawler trencher (ride on).12 Figure B.4 — Crawler trencher with elevating operator’s station.12
Tables Table A.1 — List of additional significant hazards.10
EN 474-10:2006 (E) 3 Foreword This document (EN 474-10:2006) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2007, and conflicting national standards shall be withdrawn at the latest by November 2008. This European Standard supersedes EN 474-10:1998. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. For bibliographic references, see EN 474-1:2006. EN 474 "Earth-moving machinery — Safety" comprises the following parts: Part 1: General requirements Part 2: Requirements for tractor-dozers Part 3: Requirements for loaders Part 4: Requirements for backhoe-loaders Part 5: Requirements for hydraulic excavators Part 6: Requirements for dumpers Part 7: Requirements for scrapers Part 8: Requirements for graders Part 9: Requirements for pipelayers Part 10: Requirements for trenchers Part 11: Requirements for earth and landfill compactors Part 12: Requirements for cable excavators This European Standard is intended for use in combination with Part 1 of the series. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
EN 474-10:2006 (E) 4 Introduction This part of EN 474 is a type C standard as stated in EN ISO 12100-1:2003. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard.
EN 474-10:2006 (E) 5 1 Scope This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to trenchers as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006. This part does not deal with the specific hazards related to derivative use. This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for trenchers. This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of trenchers. This European Standard is not applicable to trenchers manufactured before the date of publication of this European Standard by CEN. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 474-1:2006, Earth-moving machinery — Safety — Part 1: General requirements EN 13510:2000, Earth-moving machinery — Roll-over protective structures — Laboratory tests and performance requirements (ISO 3471:1994 including Amendment 1:1997 modified) EN ISO 3411:1999, Earth-moving machinery — Human physical dimensions of operators and minimum operator space envelope (ISO 3411:1995) EN ISO 6682:1995, Earth-moving machinery — Zones of comfort and reach for controls (ISO 6682:1986 including Amendment 1:1989) EN ISO 7096:2000, Earth-moving machinery — Laboratory evaluation of operator seat vibration (ISO 7096:2000) EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) ISO 6016:1998, Earth-moving machinery — Methods of measuring the masses of whole machines, their equipment and components ISO/DIS 6393:2004, Earth-moving machinery — Determination of sound power level noise emissions — Stationary test conditions ISO/DIS 6394:2004, Earth-moving machinery — Determination of emission sound pressure level at operator's position — Stationary test conditions ISO 12509:2004, Earth-moving machinery — Lighting, signalling and marking lights, and reflex-reflector
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.