Geosynthetics - Installing and retrieving samples in the field for durability assessment (ISO 13437:2019)

This standard specifies a method for the on-site installation, retrieval and testing of geotextile samples, irrespective of the particular degradation mechanisms to which they are exposed.
The method is also appropriate to test for mechanical damage, much of which occurs during installation, and to provide an owner with information about the state of the geotextile or geotextile-related product in his structure.
NOTE : The durability of geotextiles or geotextile-related products is assessed by short-term accelerated tests under conditions more extreme than those experienced in service. In order to establish the validity of these tests it is essential to compare their predictions with tests made on material extracted from site.

Geokunststoffe - Verfahren zum Einbau und Ausgraben von Proben im Boden (ISO 13437:2019)

Dieses Dokument legt ein Verfahren fest, wie Geokunststoffproben auf der Baustelle eingebaut und entnommen werden, unabhängig von den speziellen Alterungsmechanismen, denen sie ausgesetzt sind.
Dieses Verfahren ist auch als Prüfung auf mechanische Schäden geeignet, von denen viele direkt beim Einbau entstehen, und liefert dem Eigentümer Informationen über den Zustand des Geokunststoffproduktes in seinem Bauwerk.

Géosynthétiques - Installation et prélèvement d'échantillons sur le terrain pour l'évaluation de la durabilité (ISO 13437:2019)

Le présent document spécifie une méthode pour l'installation sur site et le prélèvement d'échantillons, indépendamment des mécanismes spécifiques de dégradation auxquels ils sont exposés.
La méthode est également appropriée en tant qu'essai de performance pour les dommages mécaniques qui, pour une grande part, se produisent directement lors de l'installation, et permet d'informer le maître d'ouvrage de l'état du géosynthétique ou produit apparenté utilisé dans sa structure.

Geosinetika - Namestitev in pridobivanje vzorcev na terenu zaradi ocenjevanja trajnosti (ISO 13437:2019)

Ta standard določa metodo za namestitev, pridobivanje in preskušanje vzorcev geotekstilij, ne glede na določene mehanizme degradacije, ki so jim izpostavljeni.
Ta metoda je tudi primerna za preskušanje mehanskih poškodb, ki večinoma nastanejo med namestitvijo, in lastniku zagotavlja informacije o stanju geotekstilije ali po zgradbi geotekstilijam sorodnega izdelka.
OPOMBA: Odpornost geotekstilij ali geotekstilijam sorodnih izdelkov se ocenjuje s kratkoročnimi pospešenimi preskusi v pogojih, ki so skrajnejši od tistih med delovanjem. Za ugotavljanje veljavnosti teh preskusov je treba njihove napovedi nujno primerjati s preskusi na materialu, pridobljenem na terenu.

General Information

Status
Published
Public Enquiry End Date
02-Aug-2018
Publication Date
09-Oct-2019
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
02-Oct-2019
Due Date
07-Dec-2019
Completion Date
10-Oct-2019

RELATIONS

Buy Standard

Standard
SIST EN ISO 13437:2019
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 13437:2019
01-november-2019
Nadomešča:
SIST EN ISO 13437:1999
Geosinetika - Namestitev in pridobivanje vzorcev na terenu zaradi ocenjevanja
trajnosti (ISO 13437:2019)

Geosynthetics - Installing and retrieving samples in the field for durability assessment

(ISO 13437:2019)
Geokunststoffe - Verfahren zum Einbau und Ausgraben von Proben im Boden (ISO
13437:2019)
Géosynthétiques - Installation et prélèvement d'échantillons sur le terrain pour
l'évaluation de la durabilité (ISO 13437:2019)
Ta slovenski standard je istoveten z: EN ISO 13437:2019
ICS:
59.080.70 Geotekstilije Geotextiles
SIST EN ISO 13437:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 13437:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 13437:2019
EN ISO 13437
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2019
EUROPÄISCHE NORM
ICS 59.080.70 Supersedes EN ISO 13437:1998
English Version
Geosynthetics - Installing and retrieving samples in the
field for durability assessment (ISO 13437:2019)

Géosynthétiques - Installation et prélèvement Geokunststoffe - Verfahren zum Einbau und Ausgraben

d'échantillons sur le terrain pour l'évaluation de la von Proben im Boden (ISO 13437:2019)

durabilité (ISO 13437:2019)
This European Standard was approved by CEN on 5 August 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13437:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13437:2019
EN ISO 13437:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 13437:2019
EN ISO 13437:2019 (E)
European foreword

This document (EN ISO 13437:2019) has been prepared by Technical Committee ISO/TC 221

"Geosynthetics" in collaboration with Technical Committee CEN/TC 189 “Geosynthetics” the secretariat

of which is held by NBN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by March 2020, and conflicting national standards shall

be withdrawn at the latest by March 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 13437:1998.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 13437:2019 has been approved by CEN as EN ISO 13437:2019 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 13437:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 13437:2019
INTERNATIONAL ISO
STANDARD 13437
Second edition
2019-07
Geosynthetics — Installing and
retrieving samples in the field for
durability assessment
Géosynthétiques — Installation et prélèvement d'échantillons sur le
terrain pour l'évaluation de la durabilité
Reference number
ISO 13437:2019(E)
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 13437:2019
ISO 13437:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13437:2019
ISO 13437:2019(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Test method ............................................................................................................................................................................................................... 2

5.1 Identification of the initial conditions ................................................................................................................................ 2

5.2 Durability testing samples ........................................................................................................................................................... 2

5.3 Preparation of control specimens .......................................................................................................................................... 2

5.4 Retrieval of samples ........................................................................................................................................................................... 3

5.5 Testing and analysis ............................................................................................................................................................................ 4

5.5.1 Testing on retrieval samples .................................................................................................................................. 4

5.5.2 Testing on retrieval samples and control specimens ....................................................................... 4

6 General report ......................................................................................................................................................................................................... 4

Annex A (informative) Identification forms for structure, environment and geosynthetic .......................5

Bibliography ................................................................................................................................................................................................................................ 8

© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 13437:2019
ISO 13437:2019(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso

.org/iso/foreword .html.

This document was prepared by the European Committee for Standardization (CEN) Technical

Committee CEN/TC 189, Geosynthetics, in collaboration with ISO Technical Committee TC 221,

Geosynthetics, in accordance with the Agreement on technical cooperation between ISO and CEN

(Vienna Agreement).

This second edition cancels and replaces the first edition (ISO 13437:1998), which has been technically

revised.
The main changes compared to the previous edition are as follows:

— The standard has been modified to cover all geosynthetics, rather than only geotextiles. The

specific references to individual polymer types have been removed to make the standard cover all

geosynthetic products.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 13437:2019
INTERNATIONAL STANDARD ISO 13437:2019(E)
Geosynthetics — Installing and retrieving samples in the
field for durability assessment
1 Scope

This document specifies a method for the on-site installation and retrieval of geosynthetic samples,

irrespective of the particular degradation mechanisms to which they are exposed.

The method is also appropriate to test for mechanical damage, much of which occurs during installation,

and to provide an owner with information about the state of the geosynthetic product in their structure.

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 9862, Geosynthetics — Sampling and preparation of test specimens
ISO 10318-1, Geosynthetics — Part 1: Terms and definitions
3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 10318-1 and the following apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
control specimen

test specimen taken from the material delivered on site before its installation in the structure

3.2
testing sample

sample installed during construction for the purpose of installation damage or degradation assessment

3.3
retrieval sample
either testing sa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.