SIST EN ISO 17405:2014
(Main)Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014)
Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014)
EN ISO 17405 specifies the techniques for manual ultrasonic testing of claddings on steel applied by welding, rolling, and explosion using single-element or dual-element probes. The test is intended to cover detection of two-dimensional or three-dimensional discontinuities in the cladding and in the region of the interface. This International Standard does not give acceptance criteria nor define the extent of testing.
Zerstörungsfreie Prüfung - Ultraschallprüfung - Techniken zur Prüfung von Plattierungen verursacht durch Schweißen, Walzen und Explosion (ISO 17405:2014)
Dieses Internationale Norm legt Techniken für die manuelle Ultraschallprüfung von Plattierungen auf Stahl, die durch Schweißen, Walzen und Sprengen aufgetragen wurden, unter Verwendung von Sende-Empfangs-Prüfköpfen (SE-Prüfköpfen) oder Einzelelement-Prüfköpfen fest.
Die Prüfung ist dafür vorgesehen, den Nachweis von zweidimensionalen oder dreidimensionalen Inhomogeni-täten in der Plattierung und in der Grenzschicht zu erbringen.
In dieser Internationalen Norm werden weder Zulässigkeitskriterien angegeben noch wird der Prüfumfang festgelegt.
Essais non destructifs - Essais par ultrasons - Technique d'essai des placages produits par soudage, laminage et explosion (ISO 17405:2014)
ISO 17405:2014 spécifie les techniques d'essai manuel par ultrasons des revêtements sur acier appliqués par soudage, laminage et explosion en utilisant des traducteurs mono-éléments ou à émetteur et récepteur séparés. L'essai est destiné à couvrir la détection des discontinuités à 2 ou 3 dimensions présentes dans le revêtement et la région d'interface.
ISO 17405:2014 ne fournit pas de critères d'acceptation et ne définit pas l'étendue des essais.
Neporušitvene preiskave – Ultrazvočne preiskave - Tehnika preiskav oblog, pripravljenih z varjenjem, zvijanjem in eksplozijo (ISO 17405:2014)
Standard EN ISO 17405 določa tehnike za ročne ultrazvočne preiskave oblog na jeklu, ki se nanašajo z varjenjem, zvijanjem in eksplozijo, z uporabo sond, sestavljenih iz enega ali dveh elementov. Preiskava je namenjena odkrivanju dvodimenzionalnih ali tridimenzionalnih nezveznosti v oblogi in v predelu vmesnika. Ta mednarodni standard ne podaja meril sprejemljivosti in ne določa obsega preskušanja.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 17405:2014
01-oktober-2014
1HSRUXãLWYHQHSUHLVNDYH±8OWUD]YRþQHSUHLVNDYH7HKQLNDSUHLVNDYREORJ
SULSUDYOMHQLK]YDUMHQMHP]YLMDQMHPLQHNVSOR]LMR ,62
Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by
welding, rolling and explosion (ISO 17405:2014)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Techniken zur Prüfung von Plattierungen
verursacht durch Schweißen, Walzen und Explosion (ISO 17405:2014)
Essais non destructifs - Essais par ultrasons - Technique d'essai des placages produits
par soudage, laminage et explosion (ISO 17405:2014)
Ta slovenski standard je istoveten z: EN ISO 17405:2014
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
SIST EN ISO 17405:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 17405:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 17405:2014
EUROPEAN STANDARD
EN ISO 17405
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2014
ICS 19.100
English Version
Non-destructive testing - Ultrasonic testing - Technique of testing
claddings produced by welding, rolling and explosion (ISO
17405:2014)
Essais non destructifs - Essais par ultrasons - Technique Zerstörungsfreie Prüfung - Ultraschallprüfung - Techniken
d'essai des placages produits par soudage, laminage et zur Prüfung von Plattierungen hergestellt durch Schweißen,
explosion (ISO 17405:2014) Walzen und Sprengen (ISO 17405:2014)
This European Standard was approved by CEN on 21 June 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17405:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 17405:2014
EN ISO 17405:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 17405:2014
EN ISO 17405:2014 (E)
Foreword
This document (EN ISO 17405:2014) has been prepared by Technical Committee ISO/TC 135 "Non-
destructive testing" in collaboration Technical Committee CEN/TC 138 “Non-destructive testing” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2015, and conflicting national standards shall be withdrawn at
the latest by January 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17405:2014 has been approved by CEN as EN ISO 17405:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 17405:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 17405:2014
INTERNATIONAL ISO
STANDARD 17405
First edition
2014-07-15
Non-destructive testing — Ultrasonic
testing — Technique of testing
claddings produced by welding, rolling
and explosion
Essais non destructifs — Essais par ultrasons — Technique d’essai des
placages produits par soudage, laminage et explosion
Reference number
ISO 17405:2014(E)
©
ISO 2014
---------------------- Page: 7 ----------------------
SIST EN ISO 17405:2014
ISO 17405:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 17405:2014
ISO 17405:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Ultrasonic test system . 1
4.1 General . 1
4.2 Requirements regarding probes . 2
4.3 Additional requirements . 2
4.4 Instrument settings . 3
5 Preparation of the test object. 7
6 Test procedure . 8
6.1 General . 8
6.2 Movement of probe . 8
6.3 Checking the instrument setting . 8
6.4 Recording levels . 8
7 Test report . 8
Annex A (informative) Determination of focal zone.10
Bibliography .11
© ISO 2014 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 17405:2014
ISO 17405:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
ISO 17405 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 138, Non-destructive testing, in collaboration with ISO Technical Committee TC 135, Non-
destructive testing, Subcommittee SC 3, Ultrasonic testing, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
iv © ISO 2014 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 17405:2014
INTERNATIONAL STANDARD ISO 17405:2014(E)
Non-destructive testing — Ultrasonic testing — Technique
of testing claddings produced by welding, rolling and
explosion
1 Scope
This International Standard specifies the techniques for manual ultrasonic testing of claddings on steel
applied by welding, rolling, and explosion using single-element or dual-element probes.
The test is intended to cover detection of two-dimensional or three-dimensional discontinuities in the
cladding and in the region of the interface.
This International Standard does not give acceptance criteria nor define the extent of testing.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 2400, Non-destructive testing — Ultrasonic testing — Specification for calibration block No. 1
EN 1330-4, Non-destructive testing — Terminology — Part 4: Terms used in ultrasonic testing
EN 12668-1, Non-destructive testing — Characterization and verification of ultrasonic examination
equipment — Part 1: Instruments
EN 12668-2, Non-destructive testing — Characterization and verification of ultrasonic examination
equipment — Part 2: Probes
EN 12668-3, Non-destructive testing — Characterization and verification of ultrasonic examination
equipment — Part 3: Combined equipment
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1330-4 and the following apply.
3.1
test object
part to be tested
3.2
test surface
areas of the surface of the test object to which probes have to be coupled
4 Ultrasonic test system
4.1 General
The ultrasonic pulse-echo technique is used. For two-dimensional discontinuities parallel to the test
surface and three-dimensional discontinuities, straight beam probes (dual-element or single-element)
shall be used for testing with longitudinal waves.
© ISO 2014 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 17405:2014
ISO 17405:2014(E)
For discontinuities with any other orientation, dual-element angle-beam probes for longitudinal waves
can be used.
The nominal frequency shall be selected according to the purpose of the test and the characteristics of
the materials.
Frequencies from 2 MHz to 6 MHz should be preferred.
The instrument used shall comply with the requirements given in EN 12668-1, and the probes
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.