SIST EN 300 113-2 V1.4.1:2007
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
The present document covers the technical requirements for radio transmitters and receivers used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies in all or in any part of the frequencies as given below, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data.It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated demodulator and decoder. The types of equipment covered by the present document are as follows:
- base station (equipment fitted with an antenna connector, intended for use in a fixed location);
- mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
- and those hand portable stations:
a) fitted with an antenna socket; or
b) without an external antenna socket, but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input. Hand portable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [1], which states that "(...) radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radiocommunications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] may apply to equipment within the scope of the present document.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Storitev kopenskih mobilnih komunikacij - Radijska oprema za prenos podatkov (oziroma govora), ki uporablja modulacijo s konstantno ali nekonstantno ovojnico in ima antenski priključek - 2. del: Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 300 113-2 V1.4.1:2007
01-december-2007
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50
6WRULWHYNRSHQVNLKPRELOQLKNRPXQLNDFLM5DGLMVNDRSUHPD]DSUHQRVSRGDWNRY
R]LURPDJRYRUD NLXSRUDEOMDPRGXODFLMRVNRQVWDQWQRDOLQHNRQVWDQWQRRYRMQLFR
LQLPDDQWHQVNLSULNOMXþHNGHO +DUPRQL]LUDQL(1NL]DMHPDELVWYHQH]DKWHYH
þOHQDGLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land mobile service;
Radio equipment intended for the transmission of data (and/or speech) using constant or
non-constant envelope modulation and having an antenna connector - Part 2:
Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 300 113-2 Version 1.4.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 300 113-2 V1.4.1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 113-2 V1.4.1:2007
---------------------- Page: 2 ----------------------
SIST EN 300 113-2 V1.4.1:2007
ETSI EN 300 113-2 V1.4.1 (2007-07)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land mobile service;
Radio equipment intended for the transmission
of data (and/or speech) using constant or non-constant
envelope modulation and having an antenna connector;
Part 2: Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 3 ----------------------
SIST EN 300 113-2 V1.4.1:2007
2 ETSI EN 300 113-2 V1.4.1 (2007-07)
Reference
REN/ERM-TGDMR-062-2
Keywords
antenna, data, mobile, radio, regulation, speech,
PMR, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2007.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 113-2 V1.4.1:2007
3 ETSI EN 300 113-2 V1.4.1 (2007-07)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .5
1 Scope.6
2 References.6
3 Definitions, symbols and abbreviations .7
3.1 Definitions.7
3.2 Symbols.7
3.3 Abbreviations.7
4 Technical requirements specifications .7
4.1 Environmental profile.7
4.2 Transmitter requirements.7
4.2.1 Frequency error.7
4.2.1.1 Definition.7
4.2.1.2 Limit.7
4.2.1.3 Conformance.8
4.2.2 Transmitter power (conducted).8
4.2.2.1 Definition.8
4.2.2.2 Limit.8
4.2.2.3 Conformance.8
4.2.3 Maximum effective radiated power .8
4.2.3.1 Definition.8
4.2.3.2 Limit.8
4.2.3.3 Conformance.8
4.2.4 Adjacent and alternate channel power .8
4.2.4.1 Definition.8
4.2.4.2 Limit.8
4.2.4.3 Conformance.8
4.2.5 Unwanted emissions in the spurious domain.8
4.2.5.1 Definition.8
4.2.5.2 Limit.8
4.2.5.3 Conformance.9
4.2.6 Intermodulation attenuation.9
4.2.6.1 Definition.9
4.2.6.2 Limit.9
4.2.6.3 Conformance.9
4.2.7 Transient frequency behaviour of the transmitter .9
4.2.7.1 Definition.9
4.2.7.2 Limit.9
4.2.7.3 Conformance.9
4.2.8 Transmitter timeout timer .9
4.2.8.1 Definition.9
4.2.8.2 Limit.9
4.2.8.3 Conformance.9
4.3 Receiver requirements.10
4.3.1 Maximum usable receiver sensitivity .10
4.3.1.1 Definition.10
4.3.1.2 Limit.10
4.3.1.3 Conformance.10
4.3.2 Co-channel rejection.10
4.3.2.1 Definition.10
4.3.2.2 Limit.10
4.3.2.3 Conformance.10
4.3.3 Adjacent channel selectivity .10
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 113-2 V1.4.1:2007
4 ETSI EN 300 113-2 V1.4.1 (2007-07)
4.3.3.1 Definition.10
4.3.3.2 Limit.10
4.3.3.3 Conformance.10
4.3.4 Spurious response rejection .11
4.3.4.1 Definition.11
4.3.4.2 Limit.11
4.3.4.3 Conformance.11
4.3.5 Intermodulation response rejection.11
4.3.5.1 Definition.11
4.3.5.2 Limit.11
4.3.5.3 Conformance.11
4.3.6 Blocking or desensitization.11
4.3.6.1 Definition.11
4.3.6.2 Limit.11
4.3.6.3 Conformance.11
4.3.7 Spurious radiations.11
4.3.7.1 Definition.11
4.3.7.2 Limit.12
4.3.7.3 Conformance.12
5 Testing for compliance with technical requirements.12
5.1 Environmental conditions for testing .12
5.1.1 Normal and extreme test-conditions .12
5.1.2 Test power source .12
5.1.3 Choice of samples for test suites.12
5.2 Interpretation of the measurement results .12
5.3 Essential radio test suites.13
5.3.1 Frequency error.13
5.3.2 Transmitter power (conducted).13
5.3.3 Maximum effective radiated power .13
5.3.4 Adjacent and alternate channel power .13
5.3.5 Unwanted emissions in the spurious domain.13
5.3.6 Intermodulation attenuation.13
5.3.7 Transient frequency behaviour of the transmitter .13
5.3.8 Receiver Spurious radiations .13
5.4 Other radio test suites .13
5.4.1 Maximum usable receiver sensitivity.13
5.4.2 Co-channel rejection.13
5.4.3 Adjacent channel selectivity .14
5.4.4 Spurious response rejection .14
5.4.5 Intermodulation response rejection.14
5.4.6 Receiver blocking or desensitization .14
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT).15
Annex B (informative): The EN title in the official languages .17
Annex C (informative): Bibliography.19
History .20
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 113-2 V1.4.1:2007
5 ETSI EN 300 113-2 V1.4.1 (2007-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [3] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and
of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Electromagnetic compatibility and Radio
spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech)
using constant or non-constant envelope modulation and having an antenna connector, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 29 June 2007
Date of latest announcement of this EN (doa): 30 September 2007
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2008
Date of withdrawal of any conflicting National Standard (dow): 31 March 2009
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular
structure is shown in EG 201 399 (see bibliography).
ETSI
---------------------- Page: 7 ----------------------
SIST EN 300 113-2 V1.4.1:2007
6 ETSI EN 300 113-2 V1.4.1 (2007-07)
1 Scope
The present document covers the technical requirements for radio transmitters and receivers used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies in all or in any part of the frequencies as
given below, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 1 000 MHz
Receive 30 MHz to 1 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated
demodulator and decoder. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• and those hand portable stations:
a) fitted with an antenna socket; or
b) without an external antenna socket, but fitted with a permanent internal or a temporary internal 50 Ω
Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input.
Hand portable equipment without an external or internal RF connector and without the possibility of having a temporary
internal 50 Ω RF connector is not covered by the present document.
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [1],
which states that "(.) radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radiocommunications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [1] may apply to equipment within the scope of the present
document.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 300 113-2 V1.4.1:2007
7 ETSI EN 300 113-2 V1.4.1 (2007-07)
[1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[2] ETSI EN 300 113-1 (V1.6.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using
constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical
characteristics and methods of measurement".
[3] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations and of
rules on information society services.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the R&TTE Directive [1] and
EN 300 113-1 [2] apply.
3.2 Symbols
For the purposes of the present document, the symbols given in EN 300 113-1 [2] apply.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in EN 300 113-1 [2] apply.
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer of the equipment. The equipment shall comply with all the
technical requirements of the present document at all times when operating within the boundary limits of the declared
operational environmental profile.
4.2 Transmitter requirements
4.2.1 Frequency error
4.2.1.1 Definition
The frequency error is defined in EN 300 113-1 [2], clause 7.1.1.
4.2.1.2 Limit
The frequency error shall not exceed the limits in EN 300 113-1 [2], clause 7.1.3.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 300 113-2 V1.4.1:2007
8 ETSI EN 300 113-2 V1.4.1 (2007-07)
4.2.1.3 Conformance
If the transmitter adjacent and alternate channels power (clause 5.3.4) has not been measured under extreme test
conditions, then the conformance tests as defined in clause 5.3.1 shall be carried out.
4.2.2 Transmitter power (conducted)
4.2.2.1 Definition
The transmitter power (conducted) is defined in EN 300 113-1 [2], clause 7.2.1.
4.2.2.2 Limit
The transmitter power (conducted) shall not exceed the limits in EN 300 113-1 [2], clause 7.2.3.
4.2.2.3 Conformance
Conformance tests as defined in clause 5.3.2 shall be carried out.
4.2.3 Maximum effective radiated power
4.2.3.1 Definition
The maximum effective radiated power is defined in EN 300 113-1 [2], clause 7.3.1.
4.2.3.2 Limit
The maximum effective radiated power shall not exceed the limits in EN 300 113-1 [2], clause 7.3.3.
4.2.3.3 Conformance
Conformance tests as defined in clause 5.3.3 shall be carried out.
4.2.4 Adjacent and alternate channel power
4.2.4.1 Definition
The adjacent and alternate channel power is defined in EN 300 113-1 [2], clause 7.4.1.
4.2.4.2 Limit
The adjacent and alternate channel power shall not exceed the limits in EN 300 113-1 [2], clause 7.4.3.
4.2.4.3 Conformance
Conformance tests as defined in clause 5.3.4 shall be carried out.
4.2.5 Unwanted emissions in the spurious domain
4.2.5.1 Definition
The unwanted emissions in the spurious domain are defined in EN 300 113-1 [2], clause 7.5.1.
4.2.5.2 Limit
The unwanted emissions in the spurious domain shall not exceed the limits in EN 300 113-1 [2], clause 7.5.4.
ETSI
---------------------- Page: 10 ----------------------
SIST EN 300 113-2 V1.4.1:2007
9 ETSI EN 300 113-2 V1.4.1 (2007-07)
4.2.5.3 Conformance
Conformance tests as defined in clause 5.3.5 shall be carried out.
4.2.6 Intermodulation attenuation
4.2.6.1 Definition
The intermodulation attenuation is defined
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.