SIST EN 300 296-2 V1.4.1:2013
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile
service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service. The present document may apply to PMR446 equipment as defined in CEPT/ERC/DEC(98)25 [i.6]. Note that PMR446 equipment has a requirement to incorporate a receiver and may have requirements for 180 s maximum transmission time and VOX.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Storitev kopenskih mobilnih komunikacij - Radijska oprema, namenjena predvsem za analogni prenos govora, ki uporablja vgrajeno anteno - 2. del: Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Ta dokument zajema minimalne karakteristike, ki so potrebne za preprečevanje škodljivih motenj in sprejemljivo uporabo frekvenc, ki so na voljo. Ta dokument se uporablja za opremo z vgrajenimi antenami za uporabo v modulacijskih sistemih v storitvi kopenskih mobilnih
komunikacij, ki deluje na radijskih frekvencah med 30 MHz in 1000 MHz, ima medkanalske razmike 12,5 kHz, 20 kHz in 25 kHz ter je namenjena predvsem za analogni prenos govora. V tem dokumentu so podane različne zahteve za različne radijske frekvenčne pasove, medkanalske razmike, okoljske pogoje in vrste opreme, kjer je ustrezno. Ta dokument dopolnjuje standard EN 300 086 [i.4], ki zajema radijsko opremo z notranjim ali zunanjim radiofrekvenčnim priključkom za uporabo v storitvi kopenskih mobilnih komunikacij. Lahko se uporablja za opremo PMR446, kot je navedeno v CEPT/ERC/DEC(98)25 [i.6]. Opomba: zahteve za opremo PMR446 vključujejo sprejemnik ter najdaljši čas prenosa 180 sekund in VOX.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 300 296-2 Version 1.4.1SIST EN 300 296-2 V1.4.1:2013en01-november-2013SIST EN 300 296-2 V1.4.1:2013SLOVENSKI
STANDARD
SIST EN 300 296-2 V1.4.1:2013
ETSI EN 300 296-2 V1.4.1 (2013-08) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Harmonized European Standard SIST EN 300 296-2 V1.4.1:2013
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 2
Reference REN/ERM-TGDMR-303 Keywords analogue, mobile, PMR, radio, regulation, speech ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 296-2 V1.4.1:2013
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 3 Contents Intellectual Property Rights . 5 Foreword . 5 Introduction . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 6 2.2 Informative references . 6 3 Definitions, symbols and abbreviations . 7 3.1 Definitions . 7 3.2 Symbols . 7 3.3 Abbreviations . 7 4 Technical specifications . 7 4.1 Environmental profile . 7 4.2 Transmitter requirements . 7 4.2.1 Frequency error . 7 4.2.1.1 Definition . 7 4.2.1.2 Limit . 7 4.2.1.3 Methods of measurement . 7 4.2.2 Effective radiated power . 8 4.2.2.1 Definition . 8 4.2.2.2 Limit . 8 4.2.2.3 Methods of measurement . 8 4.2.3 Maximum permissible frequency deviation . 8 4.2.3.1 Definition . 8 4.2.3.2 Limit . 8 4.2.3.3 Methods of measurement . 8 4.2.4 Adjacent and alternate channel power . 8 4.2.4.1 Definition . 8 4.2.4.2 Limit . 8 4.2.4.3 Methods of measurement . 8 4.2.5 Radiated unwanted emissions in the spurious domain . 8 4.2.5.1 Definition . 8 4.2.5.2 Limit . 8 4.2.5.3 Methods of measurement . 8 4.2.6 Voice operated transmission . 9 4.2.6.1 Definition . 9 4.2.6.2 Limit . 9 4.2.6.3 Methods of measurement . 9 4.2.7 Maximum transmission time. 9 4.2.7.1 Definition . 9 4.2.7.2 Limit . 9 4.2.7.3 Methods of measurement . 9 4.3 Receiver requirements . 9 4.3.1 Average usable sensitivity (field strength, speech) . 9 4.3.1.1 Definition . 9 4.3.1.2 Limit . 9 4.3.1.3 Method of measurement . 9 4.3.2 Co-channel rejection . 9 4.3.2.1 Definition . 9 4.3.2.2 Limit . 9 4.3.2.3 Method of measurement . 10 4.3.3 Adjacent channel selectivity . 10 4.3.3.1 Definition . 10 SIST EN 300 296-2 V1.4.1:2013
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 4 4.3.3.2 Limit . 10 4.3.3.3 Method of measurement . 10 4.3.4 Spurious response rejection . 10 4.3.4.1 Definition . 10 4.3.4.2 Limit . 10 4.3.4.3 Method of measurement . 10 4.3.5 Intermodulation response rejection . 10 4.3.5.1 Definition . 10 4.3.5.2 Limit . 10 4.3.5.3 Method of measurement . 10 4.3.6 Blocking or desensitization . 10 4.3.6.1 Definition . 10 4.3.6.2 Limit . 10 4.3.6.3 Method of measurement . 11 4.3.7 Spurious radiations . 11 4.3.7.1 Definition . 11 4.3.7.2 Limit . 11 4.3.7.3 Method of measurement . 11 5 Testing for compliance with technical requirements . 11 5.1 Environmental conditions for testing . 11 5.1.1 Normal and extreme test-conditions . 11 5.1.2 Test power source . 11 5.1.3 Choice of samples for test suites . 11 5.2 Interpretation of the measurement results . 11 5.3 Essential radio test suites . 12 5.3.1 Frequency error . 12 5.3.2 Effective radiated power . 12 5.3.3 Maximum frequency deviation . 12 5.3.4 Adjacent and alternate channel power . 12 5.3.5 Radiated unwanted emission in the spurious domain . 12 5.3.6 Spurious radiations . 12 5.3.7 Average usable sensitivity (speech, field strength) . 12 5.3.8 Adjacent channel selectivity . 12 5.3.9 Intermodulation response rejection . 12 5.3.10 Blocking or desensitization . 12 5.4 Other test specifications . 12 5.4.1 Voice operated transmission . 12 5.4.2 Maximum transmission time. 13 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 14 Annex B (informative): Bibliography . 16 History . 17
SIST EN 300 296-2 V1.4.1:2013
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to the mandate M/284 from the European Commission issued under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1]. See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.1] are summarized in annex A. The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech, as identified below: Part 1: "Technical characteristics and methods of measurement"; Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates Date of adoption of this EN: 13 August 2013 Date of latest announcement of this EN (doa): 3
...
ETSI EN 300 296-2 V1.4.1 (2013-08)
Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 300 296-2 V1.4.1 (2013-08)
Reference
REN/ERM-TGDMR-303
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 296-2 V1.4.1 (2013-08)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.2.6 Voice operated transmission . 9
4.2.6.1 Definition . 9
4.2.6.2 Limit . 9
4.2.6.3 Methods of measurement . 9
4.2.7 Maximum transmission time. 9
4.2.7.1 Definition . 9
4.2.7.2 Limit . 9
4.2.7.3 Methods of measurement . 9
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 10
4.3.3 Adjacent channel selectivity . 10
4.3.3.1 Definition . 10
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 296-2 V1.4.1 (2013-08)
4.3.3.2 Limit . 10
4.3.3.3 Method of measurement . 10
4.3.4 Spurious response rejection . 10
4.3.4.1 Definition . 10
4.3.4.2 Limit . 10
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 11
4.3.7 Spurious radiations . 11
4.3.7.1 Definition . 11
4.3.7.2 Limit . 11
4.3.7.3 Method of measurement . 11
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 12
5.3.1 Frequency error . 12
5.3.2 Effective radiated power . 12
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.3.7 Average usable sensitivity (speech, field strength) . 12
5.3.8 Adjacent channel selectivity . 12
5.3.9 Intermodulation response rejection . 12
5.3.10 Blocking or desensitization . 12
5.4 Other test specifications . 12
5.4.1 Voice operated transmission . 12
5.4.2 Maximum transmission time. 13
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 14
Annex B (informative): Bibliography . 16
History . 17
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 296-2 V1.4.1 (2013-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to the mandate M/284 from the European Commission
issued under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1].
See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.1] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 13 August 2013
Date of latest announcement of this EN (doa): 30 November 2013
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 May 2014
Date of withdrawal of any conflicting National Standard (dow): 31 May 2015
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 296-2 V1.4.1 (2013-08)
1 Scope
The pres
...
Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Reference
REN/ERM-TGDMR-303
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.2.6 Voice operated transmission . 9
4.2.6.1 Definition . 9
4.2.6.2 Limit . 9
4.2.6.3 Methods of measurement . 9
4.2.7 Maxium transmission time . 9
4.2.7.1 Definition . 9
4.2.7.2 Limit . 9
4.2.7.3 Methods of measurement . 9
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 10
4.3.3 Adjacent channel selectivity . 10
4.3.3.1 Definition . 10
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
4.3.3.2 Limit . 10
4.3.3.3 Method of measurement . 10
4.3.4 Spurious response rejection . 10
4.3.4.1 Definition . 10
4.3.4.2 Limit . 10
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 11
4.3.7 Spurious radiations . 11
4.3.7.1 Definition . 11
4.3.7.2 Limit . 11
4.3.7.3 Method of measurement . 11
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 12
5.3.1 Frequency error . 12
5.3.2 Effective radiated power . 12
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.3.7 Average usable sensitivity (speech, field strength) . 12
5.3.8 Adjacent channel selectivity . 12
5.3.9 Intermodulation response rejection . 12
5.3.10 Blocking or desensitization . 12
5.4 Other test specifications . 12
5.4.1 Voice operated transmission . 12
5.4.2 Maxium transmission time . 13
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 14
Annex B (informative): Bibliography . 16
History . 17
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to the mandate M/284 from the European Commission
issued under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1].
See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.1] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ET
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.