SIST EN 300 296-2 V1.3.1:2010
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Revise LBT definition as decided during ERM#38.
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Storitev kopenskih mobilnih komunikacij - Radijska oprema, namenjena predvsem za analogni prenos govora, ki uporablja vgrajeno anteno - 2. del: Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Pričujoči dokument zajema minimalne zahtevane lastnosti, ki veljajo za potrebne, da se izognemo škodljivim motnjam in imamo spremenljivo izrabo razpoložljivih frekvenc. Pričujoči dokument velja za opremo z vgrajenimi antenami, ki se uporablja v kotno moduliranih sistemih in kopenskih mobilnih storitvah, ki delujejo na radijskih frekvencah med 30 MHz in 1000 MHz, z ločevanjem kanalov 12,5 kHz, 20kHz in 25 kHz, in je namenjen predvsem za analogni govor. V pričujočem dokumentu so podane različne zahteve za različne radijske frekvenčne pasove, ločevanje frekvenc, stanje okolja in vrste opreme, kjer ustreza. Pričujoči dokument dopolnjuje EN 300 086 [i.4], ki zajema radijsko opremo z vgrajenim ali zunanjim RF-konektorjem za uporabo v kopenskih mobilnih storitvah.
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 300 296-2 V1.3.1:2010
01-oktober-2010
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50
6WRULWHYNRSHQVNLKPRELOQLKNRPXQLNDFLM5DGLMVNDRSUHPDQDPHQMHQDSUHGYVHP
]DDQDORJQLSUHQRVJRYRUDNLXSRUDEOMDYJUDMHQRDQWHQRGHO +DUPRQL]LUDQL
(1NL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service
- Radio equipment using integral antennas intended primarily for analogue speech - Part
2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 300 296-2 Version 1.3.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 300 296-2 V1.3.1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 296-2 V1.3.1:2010
---------------------- Page: 2 ----------------------
SIST EN 300 296-2 V1.3.1:2010
ETSI EN 300 296-2 V1.3.1 (2010-07)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 3 ----------------------
SIST EN 300 296-2 V1.3.1:2010
2 ETSI EN 300 296-2 V1.3.1 (2010-07)
Reference
REN/ERM-TGDMR-289-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 296-2 V1.3.1:2010
3 ETSI EN 300 296-2 V1.3.1 (2010-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 7
4.2.2.1 Definition . 7
4.2.2.2 Limit . 7
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.3 Receiver requirements . 8
4.3.1 Average usable sensitivity (field strength, speech) . 8
4.3.1.1 Definition . 8
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 9
4.3.4.1 Definition . 9
4.3.4.2 Limit . 9
4.3.4.3 Method of measurement . 9
4.3.5 Intermodulation response rejection . 9
4.3.5.1 Definition . 9
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 296-2 V1.3.1:2010
4 ETSI EN 300 296-2 V1.3.1 (2010-07)
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 10
5.1 Environmental conditions for testing . 10
5.1.1 Normal and extreme test-conditions . 10
5.1.2 Test power source . 10
5.1.3 Choice of samples for test suites . 10
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 11
5.3.4 Adjacent and alternate channel power . 11
5.3.5 Radiated unwanted emission in the spurious domain . 11
5.3.6 Spurious radiations . 11
5.4 Other test specifications . 11
5.4.1 Average usable sensitivity (speech, field strength) . 12
5.4.2 Co-channel rejection . 12
5.4.3 Adjacent channel selectivity . 12
5.4.4 Spurious response rejection . 12
5.4.5 Intermodulation response rejection . 12
5.4.6 Blocking or desensitization . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): The EN title in the official languages . 15
Annex C (informative): Bibliography . 16
History . 17
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 296-2 V1.3.1:2010
5 ETSI EN 300 296-2 V1.3.1 (2010-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.1] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 29 June 2010
Date of latest announcement of this EN (doa): 30 September 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2011
Date of withdrawal of any conflicting National Standard (dow
...
ETSI EN 300 296-2 V1.3.1 (2010-07)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 300 296-2 V1.3.1 (2010-07)
Reference
REN/ERM-TGDMR-289-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 296-2 V1.3.1 (2010-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 7
4.2.2.1 Definition . 7
4.2.2.2 Limit . 7
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.3 Receiver requirements . 8
4.3.1 Average usable sensitivity (field strength, speech) . 8
4.3.1.1 Definition . 8
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 9
4.3.4.1 Definition . 9
4.3.4.2 Limit . 9
4.3.4.3 Method of measurement . 9
4.3.5 Intermodulation response rejection . 9
4.3.5.1 Definition . 9
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 296-2 V1.3.1 (2010-07)
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 10
5.1 Environmental conditions for testing . 10
5.1.1 Normal and extreme test-conditions . 10
5.1.2 Test power source . 10
5.1.3 Choice of samples for test suites . 10
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 11
5.3.4 Adjacent and alternate channel power . 11
5.3.5 Radiated unwanted emission in the spurious domain . 11
5.3.6 Spurious radiations . 11
5.4 Other test specifications . 11
5.4.1 Average usable sensitivity (speech, field strength) . 12
5.4.2 Co-channel rejection . 12
5.4.3 Adjacent channel selectivity . 12
5.4.4 Spurious response rejection . 12
5.4.5 Intermodulation response rejection . 12
5.4.6 Blocking or desensitization . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): The EN title in the official languages . 15
Annex C (informative): Bibliography . 16
History . 17
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 296-2 V1.3.1 (2010-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.1] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 29 June 2010
Date of latest announcement of this EN (doa): 30 September 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2011
Date of withdrawal of any conflicting National Standard (dow): 31 March 2012
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [1]. The modular
structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 296-2 V1.3.1 (2010-07)
1 Scope
The present document covers the minimum characteristics considered nec
...
Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Reference
REN/ERM-TGDMR-289-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 9
4.3.4.1 Definition . 9
4.3.4.2 Limit . 9
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.4 Other test specifications . 12
5.4.1 Average usable sensitivity (speech, field strength) . 12
5.4.2 Co-channel rejection . 12
5.4.3 Adjacent channel selectivity . 12
5.4.4 Spurious response rejection . 12
5.4.5 Intermodulation response rejection . 12
5.4.6 Blocking or desensitization . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): The EN title in the official languages . 15
Annex C (informative): Bibliography . 16
History . 17
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the ETSI standards One-
step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.1] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [1]. The modular
structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
1 Scope
The present document covers the minimum characteristics considered
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.